FREDRICK RAMOND FR41486LCB LED Linear Pendant Instruction Manual

June 1, 2024
FREDRICK RAMOND

FREDRICK-RAMOND-LOGO

FREDRICK RAMOND FR41486LCB LED Linear Pendant

DRAWING 1 – ASSEMBLY

DRAWING 2 – GLASS INSTALLATION

FREDRICK-RAMOND-FR41486LCB-LED-Linear-Pendant-FIG-
\(2\)

Mounting Instructions

  1. Find a clear area in which you can work.
  2. Unpack the fixture and glass from the carton.
  3. Carefully review instructions before assembly.
  4. Shut off the electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off.
  5. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead. DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.
  6. Determine the desired height the pendant will be installed.
  7. The fixture is supplied with assorted stem sizes. Determine what combinations of stems are needed to achieve the desired length – see Drawing 1.
  8. Slip stems over the wire and threads the first stem onto the top of the pendant, the longest stem first. Repeat this process until all required stems are threaded together.
  9. Slip the wire through the threaded nipple and thread the nipple onto the last stem installed

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS Wiring Instructions for 0-10 volt LED dimmer) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS. Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. Wiring Instructions for 0-10 volt LED dimmer) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture.

  1. To assemble shade slide decorative ring (2) over glass shade (3) and secure the ring by tightening the set screw with the allen key
  2. Place glass shade (3) and ring (2) over led assembly (1)
  3. Slide centre ring (4) over LED assembly (1)
  4. Place decorative ring (6) over glass shade (5) and secure the ring by tightening the set screw with the allen key
  5. Place glass shade (5) and ring (6) over led assembly (1)
  6. Secure end cap (8) using final (7)
  7. Go to the next page for mounting instructions

DRAWING 1 – CANOPY ASSEMBLY

FREDRICK-RAMOND-FR41486LCB-LED-Linear-Pendant-FIG-
\(2\)

  1. Find a clear area in which you can work.
  2. Unpack the fixture and glass from the carton.
  3. Carefully review instructions before assembly.

DRAWING 2 – MOUNTING

FREDRICK-RAMOND-FR41486LCB-LED-Linear-Pendant-FIG-
\(4\)

  1. To begin installation first remove the mounting plate (1) from the canopy (C). This is accomplished by threading the eight screws (2) from the side of the canopy – see

  2. DRAWING 3. After they are removed the mounting plate can be removed.

  3. Now take mounting plate (1) and attach it to the junction box (J) using two 8-32 screws NOT PROVIDED.
    NOTE: The mounting plate has 6 elongated holes that can be used as additional anchor points. It is recommended that these additional anchor points be used. Make sure to use appropriate hardware for the material the mounting plate will be attached too

  4. To assemble the fixture it is necessary to first remove the threaded nipple(S) from the canopy (C) – see Drawing 1.

  5. This is accomplished by removing the hex nut (N) and lock washer (L) from the threaded portion of the nipple inside the canopy

  6. Now take the nipple and thread it onto the top of the last stem installed on the fixture. See assembly instructions Drawing 2.

  7. Next, take the canopy and attach it to the stem. Nuts (N) and lock washers (L) were removed earlier. Note: Please make sure the square tube does not rotate against the canopy when assembling

  8. Now with assistance take the assembled fixture and lift it to the ceiling using the hook on the end of the inspection cable (I), attached to the inside of the canopy (C), and hook it into the mounting plate (1). Now slowly release the fixture until it is safely hanging from the inspection cable – see DETAIL 1.FREDRICK-RAMOND-FR41486LCB-LED-Linear-Pendant-FIG- \(6\)
    NOTE : It is still recommended that an assistant be used to support the fixture during this process.

  9.  Make all necessary electrical connections between the driver and junction box following the instruction sheet (IS18) provided.

  10. To mount canopy (C) to the ceiling, align holes (H) in the canopy with holes (B) in mounting plate (1) and thread screws removed earlier.

  11. Wiring and installation are complete and power can be restored.

DRAWING 3 – MOUNTING

Wiring Instructions for 0-10 volt LED dimmer
Your fixture is designed so it can use a standard incandescent dimmer, Or a 0-10 volt LED dimmer. If a 0-10 volt LED dimmer is used, it may be necessary to have additional wiring installed from the dimmer switch to the fixture. Consulting an electrician will be necessary

  1. If using the optional 0-10 volt dimmer there will be four wires exiting the junction box. (B) Black [+], (W) White [-], and wiring are for the 120 / 277 voltage.
  2. The (G) Gray/Pink {-} and (P) Purple {+} are for the 0-10  volt wires from the dimmer (D) – see Drawing 1.
  3. The fixture has four wires of corresponding colours. When making the wire connections follow the chart below.

Black (B) from junction box (J) wired to Black (B) from the fixture. White (W) from junction box (J) wired to White (W) from the fixture. Gray/Pink (G) from junction box (J) wired to Gray/ pink (G) from the fixture. Purple (P) from junction box (J) wired to Purple (P) from the fixture. Connect the ground wire from the fixture to the ground screw on the mounting hardware.

INCANDESCENT DIMMER USAGE
If using an incandescent dimmer follow manufacturer instructions.
NOTE: MAKE SURE TO CAP OFF THE GRAY/PINK AND PURPLE WIRE FROM THE FIXTURE

DRAWING 1

FREDRICK-RAMOND-FR41486LCB-LED-Linear-Pendant-FIG-
\(7\)

A Division of Hinkley Lighting, Inc.
33000 PIN OAK PARKWAY | AVON LAKE, OHIO 44012
toll free 800.446.5539 | phone 440.653.5500

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FREDRICK RAMOND User Manuals

Related Manuals