AIPER ZT6001 Automatic Cordless Robotic Pool Cleaner User Manual

AIPER ZT6001 Automatic Cordless Robotic Pool Cleaner

Information

Thank you for choosing Aiper.
You’ve now joined a family of millions who have already put their trust in Aiper to take care of their pools and are enjoying the convenience of a pristinely clean pool.

This user manual will help you maintain your Aiper pool cleaner and ensure it performs at its maximum efficiency for years to come. Please take a few minutes to read through this manual.
If you have any questions, please visit our website at www.Aiper.com and contact our customer service team for assistance or more information.

Aiper Customer Service

• DE Toll-Free: +49 302 178 3684
• Email: Service@Aiper.com
• Facebook: @AiperOfficial

Important Safety Precautions

Please read this manual carefully and use your Aiper pool cleaner in accordance with the manual instructions. Aiper is not liable for any losses or injuries caused by improper use of this device.

For your safety and optimal performance of this device, please read and follow the following suggestions.

1. Do not operate your Aiper pool cleaner while people or animals are in the pool.
2. Turn the cleaner off while not in use or while performing maintenance.
3. Do not allow children to ride the Alper pool cleaner under any circumstances. Please supervise children when they are around an operational Aiper pool cleaner.
4. Use only authorized Aiper power adapters.
5. The adapter cord should only be replaced by a qualified electrician or Aiper Customer Care.
6. It’s suggested to plug the power adapter into a power strip or surge protector and not directly into an electrical outlet.
7. Ensure your device is powered off and the charging port is dry before charging. While charging, your Aiper pool cleaner should be kept in a cool place. Do not cover your Aiper pool cleaner while charging as this may cause components to overheat.
8. Please store the machine indoors or in a cool place when not in use.
9. Do not run your Aiper pool cleaner out of the water as it may lead to overheating.
10. Only certified professionals should disassemble the sealed driving kit of your Aiper pool cleaner.
11. Do not operate your Aiper pool cleaner and pool filter simultaneously.
12. The oil sealing around the motor contains grease, which may cause a small amount of water pollution if the motor is damaged. If you believe there is a leak, stop using the unit immediately.
13. Do not pierce the shell of your Aiper pool cleaner, throw, or damage the cleaner intentionally.
14. When putting your device into the water, the front of the machine must face upwards and should never be placed upside down or directly thrown into the swimming pool.
15. Do not charge the cleaner when the charging port is wet.

Please read this user manual carefully before operating the device.

Structure

Specifications & Working Conditions

1. Pool Size: 300m2
2. Charger Input: 100-2 40V, 60/50Hz, 5A
3. Charger Output: 29.4 V/9A
4. Charging Time: 90 Minutes
5. Battery Life: Up to 18 0 Minutes
6. IP Grade: IPX8 Waterproof
7. Max Water Depth: 10 ft (3m)
8. Motor Power: 70W
9. Battery Pack: 9000mAh
10. Battery Pack Voltage: 25.2V

PRECAUTIONS

To work at maximum efficiency, Aiper recommends the following water conditions for your pool.

• Temperature: 50-95° F {10-35°C)
• pH Value: 7.0- 7.4
• Chlorine: Maximum 4 ppm
• NaCl: Maximum 5000 ppm

Using Your Aiper Pool Cleaner

• The machine is suitable for cleaning floors, walls, and water lines up to 300m2.

Installation

• Select the filter basket that suits your needs.
• Lift the tail end of the upper shell to open and gain access to the interior of the device.
• Insert the filter basket into the open slot as indicated in the graphic.
• After installing the filter basket, press down on the tail of the upper shell to close the device.

Operating Your Device

• Turn the dial clockwise to activate each cleaning mode.There are three cleaning modes to choose from.

Auto Mode: Floor and Wall Cleaning

• The machine will clean the pool floor and wall in turn. After cleaning the pool floor, wall cleaning will be conducted.
• When the battery reaches below 10%, the machine will stop cleaning and remain parked near the wall of your pool.

Floor Cleaning Mode

• The machine will clean the pool floor along the “S”-shaped route (WavePath TM Navigation Technology) without climbing the wall.

Wall Cleaning Mode

• The machine will clean the wall along the “N”-shaped route.
• No floor cleaning will be carried out under this mode.

• Place your device into your pool. Your device will begin cleaning within 10 seconds of reaching your pool’s floor.
• When the device has finished cleaning, or the battery is low, it will move to the edge of your pool for retrieval. Using the included hook, you can remove the device from your pool. The uniquely designed drainage system will flush the water from the system after being removed from your pool.

Disassembly And Cleaning

• Lift the rear end of the top shell to check the filter basket.
• Detach the fasteners to release the basket from the device.
• Open the tab of the filter basket.
• Remove any trash, wash the filter basket with water, and reinsert the filter basket into the device.

Charging

Charging

Fully charge your Ai per pool cleaner before using it to clean your pool.

• Switch off the power before charging, otherwise the device cannot be recharged, and a rapid alarm will be activated.
• Please remove the silicone plug before charging.
• Wipe dry the charging port before charging your device.

• Please plug the silicone plug back in after charging or before cleaning your pool.

Maintenance

Wheel Replacement

• Lift the wheel cover marked “A.”
• Remove the screws fixed to the wheel.
• Remove the shaft and sleeve cover of the wheel for complete disassembly.

Rolling Brush Belt Replacement

• Locate the back side of the rolling brush belt and peel back the silicone buckle attached to the mounting slot.
• Once all the silicone buckles are removed, replace the rolling brush belt with a new one. Align the silicone buckles with the mounting slots, and press to secure the buckles into each slot.

LED Indicator

Packing List

NO.              Name                    Model                    QTY(pc)

Warranty

This product has passed all quality control and safety tests, conducted by the technical department of the factory.

1. This product comes with a warranty that covers your item’s battery and motor from the date of purchase. The respective country’s legal provisions for warranty conditions shall apply accordingly.
2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized personnel.
3. The warranty extends only to manufacturing defects and does not cover any damage resulting from the mishandling of the product by the owner.
4. The order number or record must be presented for any claim or repair during the warranty period.
5. This is an additional warranty offered by Aiper Intelligent, LLC. at 2700 Cumberland Parkway, Suite 350, Atlanta, Georgia 30339, USA. This warranty does not affect the free-of-charge remedies for lack of confor­mity that the consumer holds against the seller, according to law.
6. Warranty Email: Service@Aiper.com

Aiper hereby declares that this product complies with all the requirements of the applicable EU directives 2014/3 5/EU (LVD); 2014/30/EU (EMC); 2011/65/EU (RoHS) – You’ll find the full text of the Declaration of Conformity, available at this QR code.

Declaration of Conformity (CE)

• The EU declaration of conformity can be requested via the address below: AIPER INTELLIGENT SARL
• 24 Avenue du Prado 1300 6 Marseille 6e Arrondissement.

www.aiper.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>