Aiper Scuba S1 Pro Robotic Pool Cleaner User Manual

June 1, 2024
AIPER

Aiper Scuba S1 Pro Robotic Pool Cleaner

Aiper-Scuba-S1-Pro-Robotic-Pool-Cleaner- PRODCUT

FCC Statement

Note: This equipment has been tested and found to comply with the limits accordingto Part 15 of the FCC Rules of a Class B digital device. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications or persons. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorientate or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the manufacturer or an experienced radio/TV technician for help.

Warning
Changes or modifications of this product are not expressly approved by the party responsible for compliance (Aiper), and unauthorized modifications could void the user’s authority to operate the equipment.

Compliance Declaration
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference,
  2. this device must accept any interference received, including interference that may cause undesired operation.

Importer. Aiper Intelligent, LLC.

  • Address: 13851 Ramona Ave, Chino, CA 91710, USA.
  • Telephone: +1866-850-0666
  • AU Toll-Free: +61(180)049-7023

IC Statements
This device complies with Industry Canada license – ICES-003. Operation is subject to the following two conditions:

  1. This device may not cause interference,
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Thank you for choosing Aiper.

  • You’ve now joined a family of millions who have already put their trust in Aiper to take care of their pools and are enjoying the convenience of a pristinely clean pool.
  • This user manual will help you maintain your Aiper pool cleaner and ensure it performs at its maximum efficiency for years to come. Please take a few minutes to read through this manual.
  • If you have any questions, please visit our website at www.aiper.com and contact our customer service team for assistance or more information.

Aiper Customer Service:

Important Safety Precautions

Please read this manual carefully and use your Aiper pool cleaner according to the manual instructions. Aiper is not liable for any losses or injuries caused by improper use of this device.
For your safety and optimal performance of this device, please read and follow the following suggestions.

  1. Do not operate your Aiper pool cleaner while people or animals are in the pool.
  2. Turn the cleaner off while not in use or while performing maintenance.
  3. Do not allow children to ride the Aiper pool cleaner under any circumstances. Please supervise children when they are around an opera- tional Aiper pool cleaner.
  4. Use only authorized Aiper power adapters.
  5. The adapter cord should only be replaced by a qualified electrician or Aiper Customer Care.
  6. It’s suggested to plug the power adapter into a power strip or surge protector and not directly into an electrical outlet.
  7. Ensure your device is powered off and the charging port is dry before charging. While charging, your Aiper pool cleaner should be kept in a cool place. Do not cover your Aiper pool cleaner while charging as this may cause components to overheat.
  8. Please store the machine indoors or in a cool place when not in use.
  9. Do not run your Aiper pool cleaner out of the water as it may lead to overheating.
  10. Only certified professionals should disassemble the sealed driving kit of your Aiper pool cleaner.
  11. Do not operate your Aiper pool cleaner and pool filter simultaneously.
  12. The oil sealing around the motor contains grease, which may cause a small amount of water pollution if the motor is damaged. If you believe there is a leak, stop using the unit immediately.
  13. Do not pierce the shell of your Aiper pool cleaner, throw, or damage the cleaner intentionally.

Please read this user manual carefully before operating the device

Structure

Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-1

Specifications & Working Conditions

  1. Pool Size : 2150 Sq.ft/ 200m.
  2. Charger Input: 100-240V, 60/50Hz, Max 2.5A
  3. Charger Output: 29.4V/ 3A
  4. Charging Time: 4 Hours
  5. Battery Life: Up to 180 Minutes
  6. IP Grade : IPX8 Waterproof
  7. Water Depth: 10ft(3m)
  8. Suction Power: 100GPM (379LPM)
  9. Battery Pack: 7800mAh (196.56Wh)
  10. Battery Pack Voltage: 25.2V

CAUTION: Do not use the device in a pool environment beyond the conditions described below, doing so may cause damage to the device that will not be covered by your warranty.

  • Temperature: 50-95°F (10-35°C)
  • pH Value: 7.0-7.4
  • Chlorine: Maximum 4 ppm
  • NaCl: Maximum 5000 ppm

Charging

  • a. Fully charge the device before using it to clean your pool.
  • b. Before charging, remove the charging port cover to check if there is any residual water in the charging port. If so, wipe dry the charging port before charging.
  • c. Insert the charging cable into the charging port of the device and then into an available electrical outlet. The LED indicator on the device will start to pulse, indicating that the device is being charged. When it is fully charged, the LED indicator will remain on.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-2.

Using Your Aiper Pool Cleaner

This device is suitable for cleaning the floors, walls, and waterlines of your pool within an area of up to 2150 Sq.ft/ 200m?

Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-3

Operating Your Device

  • a. Press and hold the Power Button for 2s to turn on/off the device.

  • b. Auto mode is the default mode for this device once turned on. Press the button to switch between Auto, Floor, Waterline, and Eco Mode.

    • Auto Mode : The device will clean your pool’s floors and walls. When the battery level is low (LED indicator turns solid red), the device will\ automatically stop cleaning and dock.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-5

    • Floor Mode: The device will clean the pool floor in a S-shaped route, without climbing or cleaning walls. When the battery level is low, the device will automatically stop cleaning and dock.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-6

    • Waterline Mode: The machine will move horizontally and clean along the waterline. When running into corners or obstacles on the pool walls, it will descend from the waterline, switch walls or bypass obstacles, and resume cleaning.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-7
      Waterline Mode

    • Eco Mode: On a fully charged battery, the device will clean the floor of your pool for 45 min once every 48 hours for one week.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-8
      Eco Mode
      Wall Mode: Only configurable via the Aiper APP, the device will clean the pool walls in an N-shaped route, and not clean the floors. When the battery level is low, the device will automatically stop cleaning and dock.
      Wall Mode

    • c. After selecting a cleaning mode, the device will rotate its water pump every 10 seconds, 3 times in total, to check if it has been put into the pool. If the device fails to detect water during this process, it will automatically shut down. The device will start cleaning within 10 seconds of reaching the pool floor.

    • d. When the battery level is low, the device will automatically stop cleaning and dock by the nearest wallAiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-10

    • e. Lift the device from the pool floor with a hook to prevent getting wet. Users can connect the hook to any standard pool cleaning rod (not included) to extend the reach of the hook.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-11

    • f. Allow the device to drain any stored water before storing it.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-17

    • g. Hold the handle and allow the device to drain any stored water.

Disassembly and Cleaning

  • a. S et aside the device in a safe, secure location and open the Top Shell.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-19
  • b. Remove the Filter Box by lifting its handle.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-20
  • c. Press the latch of the top shells latch of the filter box and at the same time pull up on the top cover handle to open the filter box.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-21
  • d. Empty the Filter Box, rinse, and replace it back into the device once cleaned.
  • e. Please remove and clean the ultra-fine filter immediately after cleaning is complete to avoid accumulation of dirt and debris which may damage the filter. It is recommended to use a high-pressure water gun to flush any accumulated debris immediately.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-22

Aiper App User Guide

How to download and install the Aiper App

  • a. Search for “Aiper” in your device App store, download, and install the APP on your mobile.
  • b. Start the app and register. Then log in to the app using the data amad added and amend that can nearidad daring intentionAiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-23
  • How to Add and Use Devices
    • a. Before adding a device, please confirm the following:
    • The area where the device is used has 2.4G Wi-Fi coverage. 5G Wi-Fi is not supported.
    • Your phone supports Wi-Fi and Bluetooth, and Bluetooth is activated.
    • The phone is within 20 ft/6 m of your new device.
    • b. Tap the “+” in the top right corner of the App’s homepage, select “Add Device”, and follow the instructions to add the device.
    • c. After adding the device, you can configure and view your Aiper device and features in the Aiper APP.

Note : If you have not purchased the Aiper HydroComm, some features of your device will only be accessible while your device is out of the water. Once submerged, you will lose connection and cannot control your device via the APP.
The Aiper HydroComm enables underwater communication and internet connectivity for your Aiper device, offering features such as waterline recall, real-time control, underwater cleaning mode switching, 24/7 water quality monitoring, and real-time fault reporting. Inquiries for purchase are welcome at Aiper.

Maintenance

Replacing the tracks.

  • a. Remove the side cover plate from the device.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-24
  • b. Remove the screws and the guide sleeves from the wheels.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-25
  • c. Pull the wheels and the track together to remove them.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-26
  • d. Align the gears on the new tracks with the gears on both wheels, then install the rear wheels and tracks together back onto the shaft sleeves.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-27
  • e. Re-install the guide sleeves by aligning their D-shaped openings with that of the shaft sleeves.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-28
  • f. Tighten the screws and re-install the side cover plate.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-29

Replacing the roller brush belt.

  • a. Find the side that looks different from the other roller brush belts, and pull down the silicone buckles that are stuck in the fixed slot.
  • b. After all the silicone buckles are pulled out, replace the roller brush belt with a new one. Align the silicone buckles with the fixed slot and pull them outward. They can be fixed after passing through the slot. Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-31

Cleaning the drain.

  • a. Lift the top shell.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-34
  • b. Remove the screws and drain cover.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-33
  • c. Remove any objects entangled in the drains fan blades, and then re-install the drain cover and screws.Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-34

Storage

Winter Tips : How to store and secure your Aiper devices

How should I store my Aiper device during the off-season?
In your pool’s off-season, such as winter months or long vacations when your Aiper device won’t be used, there are a few steps to take to protect your device and keep it in the best condition possible.

  1. Power off your device and disconnect it from the charger.
  2. Clean the device of any residual dirt, including the top & bottom shell, wheels, roller brushes, and charging port.
  3. Using a paper towel or soft cloth, wipe dry your device.
  4. Box and store your device in a cool, well-ventilated area.
  5. Charge your device every TWO months to 40%-60% battery capacity to maintain the battery health of your device.

When you’re ready to use your Aiper device in your pool, fully charge the device before using it in your pool, and never charge your device in direct sunlight.

LED Indicator Lights

Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-35

Packing List

Aiper-Scuba-S1--Robotic-Pool-Cleaner-FIG-36

Warranty

This product has passed quality control and safety tests conducted by our technicians.

  1. This product comes with a 24-month warranty that covers your item’s battery and motor from the date of purchase.
  2. This warranty is voided if the product has been altered, misused, or has been repaired by unauthorized persons.
  3. This warranty extends only to manufacturing defects and does not cover damage resulting from the mishandling of the product by the owner.
  4. The order number or record of purchase must be presented at the request of any repair claim during the warranty period.

This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

SCANNER

www.aiper.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals