SPEKTRUM iX20 Air Ware Change Log User Guide

: June 1, 2024
: SPEKTRUM

Table of Contents

SPEKTRUM iX20 Air Ware Change Log
Product Information
Product Usage Instructions
Corrections & Improvements
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

SPEKTRUM iX20 Air Ware Change Log

SPEKTRUM-iX20-Air-Ware-Change-Log-product-image

Product Information

Specifications

Product: iX20 SpektrumTM AirWareTM
Version: 1.21.06
Release Date: 2024-Mar-12

Product Usage Instructions

Model Backup Feature
The backup .iSPM files are automatically saved to the /sdcard/AirWareData/Backup folder on the internal drive. These backups are created upon initial update and after every model
change. The backup takes place in the background after model changes and will overwrite model files that match the original backup. The following procedure can be used to view/access the backup .iSPM files on the internal drive to verify that they are there, or to copy them to somewhere else of your choosing, such as a SD card or to back up on a cloud drive:

Ensure there is no SDCard in the external slot.
Follow the steps in the manual to import one of the backup files if desired.

Issue with Legacy DSMX Receivers
If you are using one of the affected receivers listed below, follow these steps:

Delete all sensors in the list.
Perform an Auto-Config to ensure sensors are in the proper order.
Make note of any sensor settings before deleting for proper reconfiguration.

We are actively working on a solution for this issue and expect to have a fix in the next release.

FAQ

Q: How can I access the backup files?
A: The backup .iSPM files are stored in the /sdcard/AirWareData/Backup folder on the internal drive. You can view or copy them to another location as needed.
Q: What receivers are affected by the legacy DSMX issue?
A: The affected receivers are AR6110, AR6115, AR6115E, AR6210, AR6255, AR400, AR600, AR6410, AR6410L, and AR6410LBL. Follow the provided steps for resolution.
Q: How can I contact support for further assistance?
A: For any questions or concerns, please reach out to our support team at productsupport@horizonhobby.com

2024-Mar-12
Version 1.21.06
New Features

Support new PowerSafe features which utilize AS6000
Support new PowerSafe “fast boot” alarm generation
Support in Sleep Mode screen for putting new PowerSafe receivers into sleep mode
Support Smart Battery data from new PowerSafe receivers
Added Servo Cycler as new default Sequencer
Added the ability to adjust the output values associated with the positions of Logical Switches

Corrections & Improvements

Updated default values for Heli, Sail, Multi OTF Ranges
Fixed rare crash when entering RX Port Assignment screen
Fixed rare crash in Sequencer screen
Corrected issue on Servo Travel screen when values are locked
Corrected behavior on Servo Travel screen when servos are reversed
Updated default values for Flight log warnings
Corrected behavior with TIMER_MIN macros that were not accounting for translations

2023-Nov-21
Version 1.10.11
New Features

Support for Spektrum Sky™ Remote ID
Telemetry warning added for Turbine Max Pump Voltage
New BNF model files added for new releases

Corrections & Improvements

Taileron differential is now properly mixed to control surfaces
Trim values are now processed properly when switching between flight modes for Aileron wing types
Updated regulatory screens
Turbine status messages are now properly displayed
Dashboard screen properly orders telemetry screens to be displayed when gaps exist in the telemetry configurations
German translation improvements
Airware no longer crashes on Motor Curve screen when motor input is invalid
Smart Battery telemetry now handles 0 Cycle data correctly
“No Data” in ESC telemetry now handled properly

2023-Jan-23
Version 1.09.07
New Features

New BNF Model Presets added
Added support for Combo Switches outside of mixing
Added support for Logical Switches
Programmable Mix names can now be edited
The battery icon on AirWare dashboard now shows an indicator when charging
The Product Information screen now has a button that will launch the Play Store app and display the AirWare app page
LT/RT/LTT/RTT can now be assigned as stick trims (aileron, elevator, rudder and throttle)
Trimmer switch setup has been moved from Digital Switch Setup to Analog Switch Setup so that they can be configured properly
New Text to Speech macros has been added to announce Lowest Cell Voltage for Smart Battery telemetry
Custom intervals can now be specified in Custom Reports in Audio Events
The quick sleep button on the Sleep Mode screen has been changed from a press and hold to a swipe motion

Corrections & Improvements

Configuration of rate values in mixes has been improved. Dragging sliders snaps to even percentage values. Separate buttons are available for incrementing by 1% or 0.1%
Dashboard Setup Telemetry Panel “+” button now works properly after a selection is canceled
Left or Right analog trims can now be used to activate a Timer
Flaperon + Taileron no longer causes roll in tail surfaces
RX Pack Capacity telemetry screen properly displays no data when Batt 2 is not present
Menu Setup screen has been removed. Enabling My List is now located in the Model Details screen for a given model
Invalid receiver information is no longer displayed in the Forward Programming screen prior to connecting to a receiver
Values are displayed properly in Travel Adjust Screen in circumstances when channels are reversed
Duplicate subcategory names are no longer allowed

2023-Jan-23

When an Emoji is included in a model name, it is replaced with an underline character when exporting an iSPM file
Volume control UI has been updated
When switching from V-tail A to V-tail B the left and right servo port assignments are maintained correctly
Sequencer Activity no longer limits available channels for Channel A on a model imported from a radio with less channels
Model Note menu now works properly in Dark Mode
GPS Altitude value properly rounded for audio callouts
Timer audio events no longer announce when changing models
Lock feature now functions properly in all mixes
Availability of turbine telemetry macros are now synchronized across the dashboard screens and gauge panels
Smart Battery low voltage telemetry alarm configuration now defaults to 4.0v
Analog trim range now functions correctly with a 30% range when step size set to one
Turbine EGT is now available as an option on gauge/dashboard pages
Sleep Mode dialog correctly shows state of Serial Port Power
Model Select screen header bar is displayed properly
Accurate values are displayed on the Flight Log telemetry screen when %Range is selected
Programmable Mixes are now shown in the Digital Switch Setup screen when a switch is assigned as source
Switch D2 and E2 now have a proper short display name
Values are now saved on Heli Cyclic/Thro Mixing screen
Mixing screen operation has been updated to be more intuitive

2022-Feb-22
Version 1.08.11
New Features

14 Channel Support Mode- 14 fully proportional channels with 2048 resolution and 22ms frame rate is now available when using the new 14 and 20 channel PowerSafe receivers.
Sailplane Camber Switch Selection- In sailplane model type, the camber screen now allows all the switches and levers to be assigned as an input.
Renaming Channel Names – The ability to edit channel names has been added to the Servo Setup screen.
Battery Percentage Macro – A telemetry audio event macro has been added to announce the battery percentage when using a Smart Battery.
Telemetry Log Recording Enabled by Default – An “Automatic” mode has been added to the telemetry recording settings. This is now the default, and the log is saved to the internal memory of the transmitter.
Single Column Mode to Display Models – In the Model Utilities and Model Select screen there is a new option to display the list of models in a single column with larger model images.
Custom Categories – Users can now create custom sub-categories within the currently available categories. A model can be also designated to be a “Favorite” and will be displayed in a new Favorites category tab.
Importing Audio Settings – Audio Settings can now be imported from another model into the currently active model.
Max Amperage Display Reset – In the Rx Pack Capacity telemetry screen, the maximum amperage is now displayed, along with a button to reset the maximum value.

Corrections & Improvements

Programmable mixes now function properly after Channel Assign has been used to move control surfaces to non-standard channels.
High/Low Labels in Servo Setup Travel and Absolute Travel are now displayed properly for non-English languages.
Integrated and model timers now properly show values properly when greater than 24 hours.
In Sailplane model type, motor channel is now labeled properly when a model is configured as a 4 Aileron/2 Flap
Battery Not Charged for Flying alarm is now working properly
Airware no longer crashes when User Defined 2 telemetry type is logged.

2022-Feb-22

Volume Controls entry in My List now displays the proper screen
When using “Hybrid 11/22ms” Servo Mode, channels AX6 and AX7 are now hidden from use.

2021-September-02
Version 1.07.02
Corrections & Improvements

An SD card importing bug was introduced in the previous update that prevented importing models from DX systems to iX systems. This has been corrected

Version 1.07.01
New Features

Updated Telemetry Text-to-Speech Macros – All available Smart Telemetry parameters are now available as an audio event macro.
Telemetry Log Indicator – An indicator on the dashboard has been added verifying that a telemetry log is being recorded

Corrections & Improvements

The Timer Start/Stop functions now properly update in all conditions
In Hybrid 11/22ms servo mode, the available channels are now being properly displayed
Model import now ignores files that begin with a “.” dot/period
Range Test on screen instructions now references “30 Paces” matching other Spektrum transmitters and the instructions
Stick input resolution has been increased when D/R and EXPO screens are activated
Audio Event Macros: When pressing the Back Button, the Android keyboard now continues to be properly displayed
Several minor UI issues were corrected in the Servo Output Waring screen
An issue with the Macro keyboard having a duplicate display when double pressing the Macros button has been corrected

2021-July-2
Version 1.06.02
New Features

Linked or Independent Flap Speed – The default is Linked, so all flap speed settings are common. When set to Independent, the times on each position can be separate, depending on switch position.
In Sailplane model type Dual Elevator has been added as a Tail Option
Newly released BNF Model Presets have been added
More pre-installed model images to choose from

Corrections & Improvements

The Stopwatch timer no longer announces Timer Start twice when assigned to an analog input trigger
The Sequencer is now working correctly with X-Plus channels
Sequencer switch logic is incorrect
The Sequencer graphs now correctly displayed when using Step mode
Sailplane FLAP > ELE mix now functions correctly
In Sailplane model type, Camber Preset settings are now being applied correctly
Thumbnail images in the model select screen are no longer distorted
Legacy AS3X screen are now hidden when connected to newer receivers
RPM value is now being maintained after a telemetry reset
Elevon with dual rudder wing/tail type is now functioning properly
Mix values are being maintained when changing assigned switch
Preflight checklist updates are not being saved properly.
The telemetry screens now properly reset the values after hibernating
Gain are now adjustable in relative gain mode on AR636 or AR9350
In Sailplane Model Type, Motor functions is retained when importing a model
Timer telemetry is being reset when switching models
iX20 Crashing with Smart Telemetry setup has been corrected

2021-March-4
Version 1.05.02
New Features

Stick and Switch positions recorded via Telemetry Log – The stick/switch positions are now recorded in real time when using the telemetry logging feature. These logs can be viewed using 3rd party PC programs.
Automatic File Backup- Model files are now automatically backed up to internal storage when changing to another model. Also, upon initial update installation, every model file currently in-place will be backed up to the internal memory. See instructions below to learn more.
Direct access to pre-loaded BNF model files- A BNF button has been added in the Add a New Model menu in the Model Utilities screen. This list is preloaded with all current and popular Bind-n-Fly and Plug and Play models, making it even easier to get started with new models. This list will be updated and expanded with future updates. Please note – ALWAYS check control limits and directions for accuracy before initial flight.

Corrections & Improvements

Telemetry Airware issue- When using a GPS and Altitude sensor simultaneously, certain telemetry configurations could cause Airware to crash. This has been corrected.
Flap System Crow function- 100% Crow values no longer causes servo twitching on ailerons
Legacy Receiver Compatibility- Corrected servo “glitch” problem with older 22ms DSM2 and DSMX receivers.
Sequencer Graph issue- When using a Sequencer in Step Mode, in some cases the channel values and switch position were not changing as expected. The graphs are now displayed correctly.
Register Transmitter- At the bottom of the Product Information screen, once the TX is registered the Register Transmitter is replaced with Transmitter Registered.
Typo- The “Receiver is Rebooting” screen has been corrected.
Power Safe Receivers- The RX Pack Capacity/ Current readings format is now displayed in amps (not mA)
Audio Trim reports – Audio trim report now function properly when activated
BNF model sequencer issue- If a Sequencer function is added to a BNF model file the sequencer functions correctly
Model Names- The model name length is now consistent throughout the system
DSM2 mode- When selecting DSM2 in the Frame rate screen and then selecting Auto, the RXs no longer get stuck binding in DSM2 mode

2021-March-4

Sequencer w/ X-Plus- When assigning X-Plus channel to the sequencer, the channels are now functioning correctly.

How to use Model Backup Feature
The backup .iSPM files are automatically saved to the /sdcard/AirWareData/Backup folder on the internal drive. These backups are created upon initial update and after every model change. The backup takes place in the background after model changes and will overwrite model files that match the original backup. The following procedure can be used to view/access the backup .iSPM files on the internal drive to verify that they are there, or to copy them to somewhere else of your choosing, such as a SD card or to back up on a cloud drive iX20

Open File Manager app
Swipe down and select “Internal Storage”
- At this point the path at the top should say: > root > sdcard
Select the AirWareData folder
Select the Backup folder
All backup .iSPM files will be located here

The following steps can be used to import one of the backup files, if desired: (Note: Make sure there is not an SDCard in the external slot.)

From the Dashboard main screen in AirWare, single press the model name in the upper left.
Long-press Proceed to enter Model Utilities
Select the three dot menu on the upper right and select Import Models
- The initial path should be /storage/emulated/0
Scroll down the list until you find the AirWareData folder and select it
Select the Backup folder
Select desired iSPM file for input

2021-March-4
Version 1.04.11

SPEKTRUM-iX20-Air-Ware-Change-Log-1

New Features

Smart Dashboard Screens have been enhanced with a new look and continuous graphical feedback
Dark Mode has been added
Added the ability to adjust the volume with the Knob and Slider inputs
Timers can now be displayed on the Telemetry Dashboard screen
When using Vario Telemetry, a button has been added to the screen allowing altitude to be zeroed
0.1 increments are now available on all p-mixes
Importing NSPM (NX Series) format model files has been added
A Throttle Cut option is now available that requires the throttle stick to be lowered to idle after selecting throttle hold to reactivate the throttle output
A new Frame Rate screen with enhanced options is available
In the Flap System Crow is now available when dual aileron and 1 or 2 flaps is selected as a wing type.
A reversing option is available in the Flap System when throttle is selected as an input.
Flap System Speed is now independently adjustable per switch position

Corrections & Improvements

GPS Dashboard telemetry screen is now displaying metric values correctly
Flight log telemetry warnings no longer trigger on invalid data
If the receiver is powered off, and the last vario message received has a value higher than the minimum rate to trigger the vario tone, the tone will no longer continue to sound.
When using an AR637T and a Smart ESC telemetry is now being properly displayed
If the screen only is turned off Vario tones now continue to sound
Entering Forward Programming mode Heli models has been improved
Sequencer has minor display improvements
Gyro trim in Heli Mode is assigned to the trimmer switches now function correctly
Center tones have been corrected
Disable the ability to select file extension when exporting files
My List no longer crashes when Forward Programming is selected
Sailplane motor setting are now being imported correctly from SPM file

2021-March-4

French translations have been improved
GPS telemetry now reports correct longitude if less than -100.
AirWare now handles corrupt Smart Batt telemetry data
Curved mixes are now properly saving Combo Switch settings
In User Defined telemetry screens the sensors are now being displayed properly
Updated TextGen telemetry processing
Digital Switch Assignment screen no longer crashes if an unknown switch is used
Vario graph should is always active
6SLipoMon telemetry sensor screen is displaying values correctly
Telemetry log files are working correctly if an analog input is used as trigger
Combo switch functionality has been enhanced
Telemetry Dashboard Panels are maintaining their names when imported.
Voice center tone import from NX to iX radios is functioning correctly
Texts embedded within a macro expansion are now being translated

NOTE: We’ve identified an issue in this and previous code versions when using older legacy DSMX 4- and 6-channel receivers. This issue can cause servos to “twitch” every 10 seconds. We are working on a solution and expect to correct this in the next release. If you are using one of the receivers listed below, we recommend re-binding in DSM2 mode (USA only) or use an alternate receiver.
The affected receivers are: AR6110, AR6115, AR6115E, AR6210, AR6255, AR400, AR600, AR6410, AR6410L, and AR6410LBL.
NOTE: We’ve identified an issue when updating to v1.04.11, from previous versions. The issue stems from a specific telemetry configuration and its effect on the new Smart Dashboard screen. The problem arises when you have a GPS sensor configured in addition to an Altitude and/or AirSpeed sensor, and specifically if you have GPS configured in the list BEFORE the Altitude and AirSpeed sensor. If you go into Model Setup -> Telemetry and look at the list of sensors, they are numbered 1 through 12. If the GPS sensor is configured and it is earlier in the list than Altitude or AirSpeed, then before you perform the update to v1.04.11, you will want to change the order of those sensors.
There are several ways you can accomplish this. The simplest being you can delete all the sensors in the list and then perform an Auto-Config, verifying that it put the sensors in the proper order. You will want to make note of any settings you have for those sensors before you delete them so that you can re- configure them properly. We are working on a solution and expect to have a fix in the next release so that order will no longer matter. In the meantime, hopefully the above information will help ease some concerns when updating to the latest version. If you have questions or concerns, feel free to reach out to our support team at productsupport@horizonhobby.com

2020-August 14
Version 1.03.12
Corrections & Improvements

When programming a Custom Report using the Combo Switch w/Throttle Stick could cause a short duration loss of RF. This has been corrected.
In Forward Programming orientation images for new receivers are now included.

Version 1.03.07
Corrections & Improvements

In the previous update Dual Rate and EXPO were not being properly applied to existing model after the update. This has been corrected.
In Heli mode the Dual Rate and EXPO switch options are now selectable.
The wireless trainer system is now working correctly as an instructor.
Existing templates are no longer being lost when the system is updated

Version 1.03.03
New Features

Bind N Fly and SAFE models are now supported with 2 templates for streamlined model setup.
Switch B is now defaulted to channel 7
Available flight modes in air have been increased to 10
More curves are available in DR/Expo, Throttle Curve, Acro Pitch Curve, 1Axis Gyro Curve and Flap to Elevator Mix to support the additional flight modes
Cyclic Sequencing is now supported. Used for programing continuous flashing lights, creating repeated moving accessories etc.
The default for digital switch positions when using more than three flight modes has been changed to integrate the up to 10 available flight modes in the AR637T AS3X receiver.
Dashboard screen now allows Temp/RPM/Volts to be added after the ESC is configured

Corrections & Improvements

Left and Right trimmers are now working properly when set as Flight Mode trims
The default frame rate is now set to 22ms When using Smart Telemetry

2020-August 14

When Auto Config is applied, existing telemetry screens not in use will be removed from the telemetry screen for that model.
Smart Battery & SMART ESC screens have been improved
TextGen telemetry screen display now correctly displays the characters
AirWare crashing when accessing certain Gauges has been corrected
G-Force Telemetry is now properly displayed
TextGen now properly updates after telemetry is reset
RSSI warning is now functioning correctly
The Flap System is now handling analog inputs (mixing function) correctly
The Gyro function in ACRO is now supported in all flight modes

2020-January-08
Version 1.02.06
New Features

New model images- of the latest aircraft releases have been added
Startup Sounds- An option was added to allow the startup sound to be deactivated
AR637T Support- Forward Programming has been updated to support the new AR637T AS3X / SAFE receivers

Corrections & Improvements

Using mp3 files- When using an mp3 file for an audio event, you can now “trigger” it an unlimited number of times
Templates- When saving a file as a template, binding alerts are now properly stored and retained when creating a new model from that template.
Double tapping a Pop Up screen- no longer results in double selecting 2 of the same boxes
Timer Tones- After the timer expires, the timer start audio tone is now functioning.
Audio Event/ Combo Switch- In Audio Event/Custom Report/Combo Sw using 2 switches and the “and” function no longer causes a crash
Importing Tail types- When importing a model with a V-Tail, the elevator and rudder functions are now properly being applied.
When editing a gauge panel, the application no longer occasionally crashes
Wired Trainer- instructor mode is now functioning properly
The AS3X Menu- only appears when the telemetry function is enabled.
GBoard- With the previous update, Play Store’s installed GBoard application, caused the UI for the keyboard to be corrupted. This has been corrected.
Heli Mode My List- In heli mode with any Swash type selected besides normal, selecting and using My List could cause a crash. This has been corrected.
Sequencer- When using X+ Channels with the Sequencer the app would sometimes crash. This has been corrected.
In Telemetry File Logging- the On switch is no longer an option
Setting LTrimA or RTrimA as switch source for telemetry no longer causes AirWare to crash

2019-November-15
Version 1.01.08
New Features

Direct Model Image Access- Long pressing the model image on the main screen takes you to the image select screen allowing direct access to model images
Program Mix Reset- A reset button has been added in program mix screens to inhibit all values and functions of the entire mix
Model Search Function- A search function has been added in the model select page allowing easy access to any stored model
Wired Trainer- now available

Corrections & Improvements

Touch Switch Sensitivity- touch sensitivity has been improved plus a screen has been added that allows the touch sensitivity of switches and sticks to be adjusted.
Top Trim Audio Reports- are now announcing in the correct direction
Switch and Touch Switch order- has been reorganized in the switch selection menu for improved intuitiveness.
Cyclic to Throttle Mix- in heli mode now functions correctly.
Analog Input Warnings- no longer cause erroneous entries
Telemetry Settings Units- No longer reverts to US units if set to Metric
Preflight Checklist- settings are now importing properly

2019-November-07
Version 1.00.05
Initial Release