Kaiser S 60 I 69 XL Empire Semi Integrated Dishwasher User Manual

**S 60 I 69 XL*
DISHWASHER**

USER MANUAL

S 60 I 69 XL Empire Semi Integrated Dishwasher

DEAR CUSTOMERS, thank you for purchasing this Kaiser product.
We are convinced that you have made a right choice. You have purchased a dishwasher which satisfies the high quality demands and corresponds to comprehensive international standards.
Please read these instructions carefully before starting operation to be sure to obtain optimum performance. The following recommendations are aimed to protect you from possible inconveniences which can occur as a result of the wrong operation and, at the same time, reduce the consumption of electric energy and water. Proper operation and maintenance provide a longer service life of the unit.
The Kaiser dishwashers fulfil the main norms of safety, hygiene and environment protection in correspondence with the EU directives and are certified according to EU norms and standards (DIN ISO 9001, ISO 1400), standards of Russia (Gosstandart) and the CIS.
The company’s policy is aimed at constant improvement of product quality. Modifications made to the design and equipment result in exclusively positive changes in operating qualities of the appliances. The right for changes in the products is reserved by the manufacturer.

We wish you an effective use of the Kaiser product. Produkts.

Yours faithfully
OLAN-Haushaltsgeräte Berlin Germany

The appliances under present operating instructions are designed for domestic and not industrial use.

INSTALLATION INSTRUCTIONS

ELECTRICAL CONNECTION

Before connecting the stove to the mains power supply, make sure that:

• the supply voltage corresponds to the specifications on the data plate on the behind of the dishwasher,
• the mains supply has an efficient ground connection complying with all applicable laws and regulations.

After making sure that the voltage and the frequency values for the current in the home correspond to those on the rating plate and that the electrical system is sized for the maximum
voltage on the rating plate, insert the plug into an electrical socket which is earthed properly

This dishwasher is intended for AC power ~220 -240V, 50Hz. Use safety copper wire fuse 12 A only. Preferable is a time delay fuse or circuit breaker with a 3 mm contact spacing  which constitutes a separate circuit for the appliance.
The outlet should be placed in the adjacent cabinet. After the dishwasher has been mounted, make sure that the plug is accessible.

Before using the appliance for the first time, check up if the due grounding is provided.
For personal safety:
Do not use an extension cord or an adapter plug with this appliance.

Attention! Connection of hoses and cords as well as placing the appliance into operation must be made by a qualified expert only.

CONNECTING TO WATER SUPPLY AND SEWERAGE NETWORK

Connecting the Aqua-Stop inlet hose
The inlet hose equipped with Aqua-Stop System 1 is provided with double walls.
The Aqua-Stop System ensures blocking of water supply in case the inlet hose has broken as well as if the air gap between the hose itself and its corrugated shell is filled with water.

Connect the appliance to the water mains with new hose sets only. Never reuse old hose sets.
Water pressure must amount to 0.04 MPa (min.) and 1 MPa (max.). In case the pressure is below the minimum value, consult the Service Centre.

• Pull the inlet hose completely out from storage compartment located at the back of the dishwasher.
• While adjusting to the faucet, tighten the screw 2 of the safety inlet hose (3/4-inch thread).
• Before starting the dishwasher, turn on the faucet against the stop.

Connecting cold water

• Connect the cold water inlet hose to the threaded 3/4-inch connector. Make sure it is fastened tightly.

If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities.
If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance.

Connecting hot water
The inlet hose of the appliance can be also connected to the hot water supply provided the temperature doesn’t exceed 60° C.
In this case, both the wash cycle time and the power consumption are reduced.
For hot water connection follow the same procedure as that for cold water.

Connecting drain hose

• Connect the drain hose to the drain pipe 1 (diameter: 40 mm min.), or let it run directly into the sink 2.

Use the special plastic hose support which is delivered with the appliance.
The free end of the hose must be at a height of 40 to 100 cm and must not be immersed. Make sure that the hose is free from being bent or flattened.

Disconnecting from water supply
To disconnect the Aqua-Stop inlet hose, cut off water supply by turning off the faucet, screw out the nut of the safety inlet hose which adjusts it to the faucet.
Put the hose into the special storage compartment at the back of the dishwasher.
In case the free end of the hose is put directly into the sink, pay attention to the following:
If the sink is mounted at the height of 100 cm from the floor, the excess water cannot be drained directly into the sink.
To drain the excess water from the hose in this case, you need a pail or any other suitable container which should be put below the sink at the side of it.

INSTALLING THE DISHWASHER

Before installing the dishwasher, carry out the following preparatory steps:
Make sure you have enough space to install the appliance and to connect the water inlet and drain hoses as well as the electrical cord.
The installation space measurements are given in mm.

Furniture door’s installation

• The aesthetic panel should be processed in accordance with the illustrated dimensions.

The dimensions are given in mm.

• Install the bottom and top hooks from the interior of the furniture door by countersunk head screws 1.
• Put the hook into the slot 2 of the outer door of dishwasher and hang the furniture door.

After that it is necessary to fix the panel on a door of a dishwasher by screws from the inside of the door through corresponding holes 3.
For this purpose:

• Take away the cover 4,
• Pin up the screw 5,
• Get back the cover.

The door springs are set at the factory to the proper tension for the outer door. If aesthetic wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting screw 6 to drive the adjustor 7 to strain or relax the steel cable.
Door spring tension is correct when the door remains horizontal in the fully opened position, yet rises to a close with the slight lift of a finger.

Once the appliance is positioned, level the dishwasher by adjusting the feet 1 and 2 (screw in or out). The inclination angle must not exceed more than 2°.
Ensure that the space between the contact surfaces at the top of the appliance is not more than 5 mm. Align the appliance door with the edge of the kitchen furniture unit.

• Connect the inlet and drain hoses as well as the power cord.
• Stick the safety adhesive covering 3 to the inner side of the working surface in the unit where the dishwasher is to be installed. To do that, first remove the stripe of paper to set the adhesive side free. The safety covering is intended to protect the furniture surface from the steam which comes out of the dishwasher in small quantities every time you open the door of the appliance.
• Putting the dishwasher on slide-rails 4.
• Push the dishwasher into the unit.
• Fix the dishwasher in the unit with two countersunk head screws 5.

While installing the dishwasher, leave some free space for the appliance door 6 to open.

SAFETY CONDITIONS

• Service and repair of the appliance should be carried out only by the representative of an authorized service centre.
• During installation, the power cord must not be excessively or dangerously bent or flattened.
• Do not operate the dishwasher unless all enclosure panels are properly mounted. In case the dishwasher is being operated, open the door carefully: water can flow out.
• The dishwasher is intended for house utensils only. In case of unauthorized operation or wrong service the manufacturer does not bear any responsibility for possible damages.
• Use only detergent and rinse additives intended for an automatic dishwasher. Never use soap, laundry detergent, or hand washing detergent in the dishwasher. Keep these products out of reach for children.
• Don’t forget to close the appliance door after having loaded or unloaded the dishwasher. The open door can lead to a trouble.
• Do not wash plastic items in the dishwasher unless they are marked dishwasher safe or the equivalent.
• Keep children away from detergent and rinse aid as well as from the open door of the dishwasher: there could be still some detergent left inside.
• Do not tamper with controls.
• Little children should be supervised to ensure that they do not play with the appliance.
• Do not place any heavy objects on the dishwasher’s door when it is open. The appliance can tip forward.
• When loading items to be washed: Locate sharp items so that they are not likely to damage the door seal. Load sharp knives backside up to reduce the risk of being cut. Place long and sharp tableware on the additional top basket horizontally.
• Using a dishwasher, ensure that plastic items don’t get into contact with the heating element.
• In case the power cord is damaged, to prevent the slightest risk, it should be replaced only by a qualified representative of the manufacturer or an expert from the service centre.
• To connect the appliance to the water supply use new hose sets only. The old hose sets are not reusable.
• The maximum permissible inlet water pressure is 1Mpa (10 bar), while the minimum permissible inlet water pressure is 0,04Mpa (0,4 bar).

Warning! The manufacturer declines all responsibility for damage or injury if the above instructions and general safety precautions are not respected.

BRIEF DESCRIPTION

With the XL model with width 60 cm, Kaiser introduces a new generation of dishwashers to you, which are notable for the modified construction and innovative design.
The main targets while developing the new generation dishwashers were high efficiency, reliability and simplicity in use.
Both the dishwashers and baskets for utensils have become more capacious.

IMPORTANT!
To use the dishwasher more effectively, read these instructions carefully. Keep this brochure safe for further using.

GENERAL VIEW

1. Top spray arm
2. Inner pipe
3. Lower spray arm
4. Filter assembly
5. Salt container
6. Dispenser
7. Lower basket
8. Upper basket
9. Cutlery drawer 3D Unlimited
10. Adjuster for feet
11. Drain Pipe Connector
12. Inlet Pipe Connector

CONTROL PANEL
The control panels of our dishwashers possesses not only the perfect design, but also really convenient programming.

1 Power switch: to turn ON/OFF – the power supply
2 Program button
3 Delay button
4 Group of programs indicators
5 LCD-display shows program duration time, delayed start, error codes etc.
6 Group of warning indicators
7 Indicators of functions and spray arms
8 Function button
9 Alternate button – upper or lower corb washing
10 Program indicator Auto
11 Program indicator Intensive
12 Program indicator Universal
13 Program indicator Eco| 14 Program indicator Glass
15 Program indicator 90 min
16 Program indicator Quick
17 Program indicator Soak
18 Warning indicator Rinse aid
19 Warning indicator Salt
20 Warning indicator Water Faucet
21 Function indicator Power wash
22 Function indicator Extra drying
23 Function indicator Turbo speed+
24 Function indicator Energy save
25 Spray arm indicator Upper basket
26 Spray arm indicator Lower basket
---|---

EQUIPMENT

LOADING THE DISHWASHER BASKETS
To achieve a better performance of the dishwasher, keep to the following loading guidelines.
The construction and the design of tableware and cutlery baskets may vary depending on the model. The consumer qualities, however, remain unaffected.

Using the upper basket
The upper basket is designed to hold more delicate and lighter dishware such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty).
Position the dishes and cookware so that they do not get moved by water sprays.
The upper basket can be adjusted at different height by putting wheels 1 into rails. For this purpose it is necessary to remove stoppers of the rails.
The upper basket is equipped by folding frames which allow to place tea cups at two levels effectively and to keep high wine glasses safe while washing.

Cutlery drawer 3D Unlimited
Maximum versatility and convenience.
Our new cutlery drawer is more flexible and safer than ever. Not only it is slidable to provide extra space for tall utensils like salad servers or knives in the middle rack, but now it is also foldable – use just one finger to collect the forks and knives.
Thanks to that, a thorough and at the same time sparing washing as well as profound drying – without any spots left – is provided.
After the washing has been finished, you can take out the cutlery drawer and conveniently arrange it for unloading.

Using the lower basket

It is advisable to place larger items which are most difficult to clean into the lower basket: pots, pans, lids, trays and bowls, as shown in the figure.
It is preferable to place trays and lids on the side of the baskets in order to prevent the rotation of the top spray arm from being blocked.
Pots, bowls, cups etc, must always be placed upside down. High pots should be slanted to allow water to flow out. It is preferable to place serving dishes and lids on the side of the racks in order to avoid blocking the rotation of the top spray arm.
The maximum diameter advised for plates in front of the detergent dispenser is of 19 cm, this not to hamper the opening of it.
The bottom basket is provided with special section bars for bigger pots, pans and oval platters.
The dishwasher is also equipped with supports for washing oven trays. They are installed respectively on the left, 1 and right side, 2 of the lower basket. These supports can also
accommodate other wide items such as trays, large dishes, oven racks, and the like.
Place dishes, including plates, as shown in the figure: large diameter dishes – closer to the back sof the basket, 3; smaller crockery – closer to the
front of the basket, 4.

DETERGENT DISPENSER

The dispenser 1 must be refilled before starting each wash cycle in correspondence with the instructions provided in the •Wash Cycle Table• (see p. 60).
Your dishwasher uses less detergent and rinse aid than conventional dishwashers.
The special design of the detergent dispenser enables using of powder or tabs detergent.

Caution! Irrespective of the detergent always fill salt container.
Generally, only one teaspoonful of detergent is enough for the ordinary wash load.
More heavily soiled items, however, need more detergent.
Always add the detergent just before starting dishwasher, otherwise it could get damp and will not dissolve properly.

Amount of Detergent to Use

Use only detergent specially intended for dishwashers.
Keep your detergent fresh and dry.
Do not put powder detergent into the dispenser in advance, do it directly before starting the wash cycle.
If the water isn’t too hard, you may also prevent the formation of deposits by adding detergent. The amount of detergent needed can vary due to differences in water hardness. To determine the water hardness in your area, contact your local water utility or area water softening company.
The harder the water, the more detergent you may need.
Remember, you should adjust the amount of detergent you use by small amounts until you find the correct amount.

Caution! Dishwasher detergent is corrosive! Take care to keep it out of reach for children.

RINSE AID DISPENSER

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes which can leave spots and streaks.
It also improves drying by allowing water to “sheet” off the dishes.
The dishwasher is designed to use liquid rinse aids.
The rinse aid dispenser is located inside the door next to the detergent dispenser.

To fill the dispenser:

1. Remove the rinse reservoir cap by lifting up the handle,
2. Pour the rinse aid into the dispenser, being careful not to overfill,
3. Close the cap.
4. Wipe away any spills with a damp cloth.

The dispenser holds approx. 100ml of rinse aid.

Adjusting Rinse Aid Dispenser

A measured amount of rinse aid is released from the dispenser during the final rinse.
Too much rinse aid can result in lather of foaming and cause cloudiness or steaks on your dishes.
If the water in your area is very soft, you may not need rinse aid. If you do, you can dilute the rinse aid with an equal amount of water.

The rinse aid dispenser 1 has six settings.
Always start with the dispenser set on 1.
If spots and poor drying are problems, increase the amount of rinse aid dispensed by removing the dispenser lid and rotating the dial to 2.
If the dishes still are not drying properly or are spotted, adjust the dial to the next higher number until your dishes are spot-free.
We recommend setting on 4.
If the water isn’t too hard, you may also prevent the formation of deposits by adding rinse aid.
The amount of rinse aid needed can vary due to differences in water hardness. To determine the water hardness in your area, contact your local water utility or area water softening company.

When to Refill the Rinse Aid Dispenser
The rinse aid should be added, when LCD display shows corresponding message or when the Rinse aid warning symbol on the control panel with LED indication goes on.

WATER SOFTENER

The hardness of the water varies from place to place.
If hard water is used in the dishwasher, deposits will form on the dishes and utensils.
The appliances are equipped with a special softener that uses salt specifically designed to eliminate lime and minerals from the water.

Loading the Salt into the Softener
Always use salt intended for use with dishwashers.
The salt container 1 is located beneath the lower basket and should be filled as follows:

• Remove the lower basket and then unscrew and remove the cap from the salt container,
• If you are filling the container for the first time, fill 1 L of its volume with water,
• Place the end of the funnel (supplied) into the hole and introduce about 2 kg of salt. It is normal for a small amount of water to come out of the salt container,
• Carefully screw the cap back on.

The salt container must be refilled when LCD display shows corresponding message or when the salt warning symbol for the machines with LED indication comes on. Usually, the salt warning message on LCD display / symbol on LED control panel is still on for a certain time after the salt container is refilled with salt and goes out as soon as the salt has dissolved completely.
If there are spills of the salt, a soak program could be run to wipe them out.

Adjusting Salt Consumption
The dishwasher allows adjusting the amount of the consumed salt depending on the hardness of the water used.
This feature ensures optimizing and customizing of salt consumption.
Setting should be made accordingly the following table:

Water hardness| Selector position| Salt consumption (gr/cy)| Cycle quantity / 1 kg
---|---|---|---
°dH| °fH| °Clarke| mmo1/1
0-5| 0-9| 0-6| 0~0,94| H1| 0| /
6-11| 10-20| 7-14| 1,0-2,0| H2| 10| 9
12-17| 21-30| 15-21| 2,1-3,0| H3| 5| 12
18-22| 31-40| 22-28| 3,1-4,0| H4| 3| 20
23-34| 41-60| 29-42| 4,1-6,0| H5| 2| 30
35-55| 61-98| 43-69| 6,1-9,8| H6| 1| 60

FILTERING SYSTEM

For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub. The filter prevent larger remnants of food or other objects from getting inside the pump. This residue can occasionally clog up the filters.
There are three components of the filtering system: the main filter, the coarse filter, and the fine filter.

1. Main filter
   Food and soil particles trapped by this filter are pulverized by a special jet on the lower spray arm and washed down the drain.

2. Coarse filter
   Larger items, such as pieces of bones or glass, which could clog the drain, are trapped in the coarse filter. To remove an item caught in this filter, gently squeeze the tabs on top of this filter and lift it out.

3. Fine filter
   This filter holds soil and food residue in the sump area and prevents it from being redeposit on the dishes during a cycle.

OPERATING THE DISHWASHER

Before you first use the dishwasher:

• Remove packing details and materials from the device,
• Fill corresponding dispensers with a detergent, water softener and rinse aid,
• Make sure that the power cord is plugged in the power outlet,
• Check up if the inlet hose and drain hose are connected duly,
• Make sure if the faucet is turned on against the stop.

ELECTRONIC PROGRAMMABLE CONTROL

1. Button turn-on/ turn-off the dishwasher;
2. Programs’ choise button;
3. Delayed start button;
4. Group of programs indicators;
5. Display;
6. Warning indicators;
7. Group of functions and alternate wash indicators;
8. Functions choice button;
9. Spray arms choice button.

• By pushing the programs’ choise button 2 (P) you can choose one of the programs.
The correspondent indicator of the group 4 will light on.
The switching of programs goes in such an order:
Programs: Auto → Intensive → Normal → Eco → Crystal → 90 min → Quick → Soak

• By pushing the delayed start button 3 you can choose the time you need.
  Delay time: 00:00 — 24:00 The delayed start time wil be shown on display 5.

• You can select one of them by pressing the function selection button 8. The corresponding display of group 7 lights up.
  The functions are switched in the following order: Function selection: Power Wash → Extra Dry → Turbo Speed + → Energy Saving

Alternate Wash: this function allows you to load either the upper, the lower or both basketss together as required for easy and economical washing.

Starting a washing program

Before the beginning of a wash cycle:

• Draw out the lower and the upper basket, load the dishes and push them back. It is advisable first to load the lower basket basket, then the upper one,
• Fill in a detergent dispenser.

Caution! Load only dishwasher safe utensils.

• Press the Power button 1.
• Choose a program by pushing the Program button 2 (P). The response indicator 3 will turn on.
• Close the door with some force, to ensure it is closed properly. You can hear a click which indicates that the door is tightly closed.

The dishwasher begins a wash cycle or the delay time starts.
If the door is open during the washing, the dishwasher will pause; the buzzer will ring once every minute. After closing the door the washing cycle will start after 10 seconds.
When the wash cycle finishes, the buzzer rings for 8 seconds and the dishwasher enter off condition (if a cycle with delay time ends, the buzzer will not ring).

Changing the program
A program can only be changed if it has been running only for a short period of time, otherwise the detergent may have already been released or the the wash water with detergent has already been drained. If this is the case, the dishwasher needs to be reset and the detergent dispenser must be refilled. To reset the dishwasher, follow the instructions below:

• Open the door a little to stop the dishwasher, after the spray arm stopped working, you can open the door completely.
• Press Program button, 1 (P) more than three seconds the machine will be in program selection mode.

You can change the program to the desired cycle setting.

Wash cycle ending
At the end of a wash cycle for 8 seconds the buzzer produces an acoustical signal.
Open the door. Press the button 2 (ON/ OFF) to switch off the dishwasher.
Wait a few minutes before you start to reload the dishwasher: the dishes will get dry and not so hot.
The recommended order of the removal dishes from the dishwasher:

1. Lower basket,
2. Upper basket,
3. Cutlery drawer.

Delay start time

If necessary, you can start a wash cycle at any convenient time by using the delay start up to 24 hours.
To select the Delayed start program:

• Push the button 1 (ON/ OFF).

• Touch the button 2 to set the delay time from 00:00 up to 24:00 hours in 30 minutes step.
  The delayed start time is shown on display 3.

• Select the required program by pressing button 4;

• Close the door with some force, to ensure it is closed properly. You can hear a click which indicates that the door is tightly closed.

As soon as the selected delay time is over, the wash program begins.
After entering the delay phase, the delay remaining time will count down in terms of minute.
The machine will start washing when the delay phase ends. All the conditions in delay time wash are the same with non-delay wash, except that the buzzer does not ring after the delay washing ends.

Other functions
If the amount of salt and rinse aid is insufficient, the corresponding symbol on the panel lights up: «Add salt», 1 or «Add rinse», 2. If the quantity of salt or rinse aid is enough, display doesn’t show any messages.

You can add additional functions to the selected dishwashing program:
3 Power wash is an even more powerful wash with a high temperature, used for very dirty dishes;
4 Additional drying – if you want to dry the washed dishes faster and better;
5 Turbo speed is an accelerated dishwashing;
6 Energy saving – if you do not fill the dishwasher completely, it is recommended to use this function to save water and energy;
7 Washing only in the upper basket;
8 Washing only in the lower basket.

WASH CYCLE TABLE

Cycle Selection Information| Cycle Description| Detergent pro/main| Rinse aid
---|---|---|---
Auto
The program checked automatically dirtiness of dishes and choose an optimal mode| Pre-wash (45 °C) Auto wash (45- 55 °C)
Rinse (62 °C) Drying| 5/ 30q| √
1 or 2 tabs
Intensive
For the heaviest soiled loads, such as pots, pans, glasses old dishes and dishes with dried food particles| Pre-wash (50 °C)
Main wash (65 °C)
Rinse Rinse (65°C)
Drying| 5/ 30 q| √
1 or 2 tabs
Normal
For normally soiled loads, such as plates, glasses and slightly soiled pans, standard daily cycle| Pre-wash (45 °C) Main wash (55 °C) Rinse
Rinse (65°C) Drying| 5130 q| √
1 or 2 tabs
Eco
For slightly soiled loads, such as plates, glasses, bowls and slightly soiled pans| Pre-wash
Main wash (50 °C)
Rinse (65°C) Drying| 5/ 30 q| √
1 or 2 tabs
Crystal
For slightly soiled loads, such as glasses, crystal and fine china| Pre-wash Main wash (40°C)
Rinse
Rinse (60 °C)
Drying| 5/ 30 q| √
1 or 2 tabs
90 min
This washing program takes 90 minutes| Wash(60T2) Rinse
Rinse(50°C)
Drying| 3 q| √
1 tab
Short
A shorter wash for slightly soiled loads which do not need drying| Main wash (40 °C)
Rinse
Rinse (45 °C)| 20 g|
Soak
To rinse dishes that you plan to wash later that day| Rinse| 0 g|

CARE AND ATTENDANCE

Keep Your Dishwasher in Shape
After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odours do not remain trapped inside.
Before cleaning or performing maintenance, always remove the plug from the outlet. Do not run risks.
When you go on holiday, it is advisable to run a wash cycle with the dishwasher being empty. After that remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar.
This will help the seals last longer as well as prevent the originating of disagreeable odours within the appliance.
If the appliance has to be displaced, try to keep it upright.
If absolutely necessary, it can be tilted backwards. One of the factors which cause the formation of odours in the dishwasher is food particles trapped in the seals.
Regular cleaning with a damp sponge is an effective preventive means.

Cleaning the exterior parts
To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products.
Rather, use only a cloth and warm soapy water.
To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or a cleaning product made especially for dishwashers.
To clean the control panel, use a slightly dampened cloth; dry thoroughly.
To clean the edge around the door, you should use only a soft warm, damp rag.
To prevent penetration of water into the door lock and electrical components, do not use a spray cleaner of any kind.
Never use a spray cleaner to clean the door panel, for it could damage the door lock and electrical components.

Cleaning the Filters
For best performance and results, the filter assembly must be cleaned.
The filter efficiently removes food particles from the wash water, allowing it to be recalculated during the cycle.
For this reason, it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running water. Inspect the filters for und obstructions every time the dishwasher has been used.
By unscrewing the filter cylinder, you can remove the filter system. Remove any food remnants and clean the filters under running water.

To clean the coarse filter and the fine filter, use a cleaning brush.
Step 1: Contra rotate the filter cylinder, and then lift it up;
Step 2: Lift the main filter up;
Step 3: Lift the fine filter.

NOTE: If do it from step1 to step 3, the filter system will be removed; while if do it from step3 to step 1, the filter system will be installed.

Caution! Never run the dishwasher without filters.
Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils.

Cleaning the Spray Arms
It is necessary to clean the spray arms regularly, for hard water chemicals can clog the spray arm jets and bearings.

• To remove the upper spray arm 1, hold the nut 2 in the center still and rotate the spray arm clockwise to remove it.
• To remove the lower spray arm 3, pull out the spray arm upward.
• Wash the arms in soapy and warm water and use a soft brush to clean the jets,
• Replace them after rinsing thoroughly.

Protecting Against Freezing
If your dishwasher is left in an unheated place during the winter, ask a service technician to:

• Cut off electrical power to the dishwasher.
  Remove fuses or trip circuit breaker,

• Turn off the water supply and disconnect the water inlet pipe from the faucet,

• Drain water from the inlet pipe and faucet,

• Reconnect the water inlet pipe to the faucet.

Remove the plastic sump cover of the bottom tub.
Use a sponge to soak up water in the rubber boot.

Alternate inspection
Besides the current maintenance the user is duty bound to the following actions:

• Alternate check and maintenance of dishwasher elements and assemblies,
• Let the dishwasher be checked by the customer service after expiration of the warranty once in two years,
• Abolishment of noticed errors.

Note! All installing and maintenance actions mentioned on the top as well as reparations are to be accomplished by an authorized installer.
The user is responsible for the irreproachable condition and professional use of the unit. If the customer service is called because of an operating mistake, the visit is liable to pay costs in the warranty, too.
Damages, which are caused through not following this instruction, are not approved.

What to do, if?
Every damage:

• Disconnect the apparatus from the power supply,
• Acquaint the exigency of a reparation Service-Centre or another organisation, which has the corresponding rights.

Problems and mistakes can happen during the usage of the unit. Some remote mistakes the user can abolish on his or her own through following the advices mentioned in the table below. Before contacting the customer service the following points are to be checked consecutively:

is not turned on
Water pressure is low| Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Make sure the dishwasher is switched on and the door is closed securely
Make sure the power cord is properly plugged into the wall outlet Check if the water supply is connected properly and the water is turned on
Drain pump doesn’t stop| Overflow| The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the drain pump Cut off the water supply  and to contact an expert of the service centre
Noise| Large rests of food
Utensils are not secure in the baskets or some small items have dropped into the basket Improper basket loading| Noise of crushing of the large rests of food
Load utensils without large rests of food
Ensure everything is secure in the dishwasher
Make sure that the action of the detergent dispenser and spray arms are not blocked by large dishware
Knock in a waterpipe| Possible mistake at installation of a water pipe| It does not influence function of a dishwasher
Stained tub interior| Improper detergent| Use only the special dishwasher detergent to avoid suds
Smudges on glassware| Rinse agent dispenser is empty| Make sure that the rinse agent dispense is filled
Suds in the tub| Improper detergent| Use only special dish washer detergent to avoid suds. If
this occurs, open the dishwasher and let suds
evaporate
 The utensils do not dry or there are spots on glasses and cuttlery| Low dosage of a rinse aid or rinse aid dispenser empty| Fill rinse aid dispenser, increase a dosage of a rinse aid or at further fillings use other grade of a rinse aid (Section see „Care and attendance”)
White strike on utensils, a dairy strike on glasses and tableware| Low dosage of a rinse aid Water softener
for salt empty| Increase a dosage of a conditioner (Section see „Care and attendance”)
Fill water softener with special salt (Section see „Water softener”)
Brownish bluish strike on glasses.
The strike is not washed off| Old detergent (see expiration date)| Replace a detergent
Glasses become muddy and change the color| These glasses are not intended for washing in a dishwasher| Wash in a dishwasher only the utensils intended for it
The tea strike or lipstick is not completely eliminated| The chosen program has low temperature| Choose the program with a higher temperature
The cover of the detergent dispenser not closed| Probably the latch is blocked by the rests of the stuck together detergent| Eliminate the rests of the detergent
Dishes and flatware not clean| Improper program
Low dosage of a washing means
The utensils incorrectly placed in the machine Filters are littered or inserted incorrectly.
Are littered jets of the arms| Select a more intensive program
Apply more detergent
Pay attention to the instruction in section “Dishwasher loading”
Whether check up if the group of filters is correctly inserted, probably they need to be cleaned. If necessary, also clean jets of the arms (Section see „Care and attendance”)
The detergent dispenser contains stuck together rests of detergent| The dispenser of detergent was damp
during filling| Fill only dry dispenser of detergent
Tableware and glasses remain slippery and have a bluish strike| Greater dosage of a rinse aid| Reduce a dosage of a rinse aid (Section see „Rinse aid dispenser”)
White film on inside surface| Hard water minerals| Adjust a dosage of salt for mitigation of hardness of water To clean the interior, use a damp sponge with dishwasher detergent and wear rubber gloves
Water in a dishwasher upon termination of the program| The group of filters is littered Drain hose is bend| First of all switch off the dishwasher and cut off the water supply.
Clean the filters (Section see „Care and attendance”)
Eliminate a handicap of a drain hose
After the wash program is over, the walls remain wet| It is not a mistake, but a normal functioning of the device| At slightly open door humidity will evaporate in a short time
Traces of rust on tableware| Tableware unstable ageist rust| Wash only the tableware intended for a dishwasher
Black or gray marks on dishes| Aluminum utensils have rubbed against dishes| Wash in a dishwasher only the utensils intended for it
Water remaining in the bottom of the tub| This is normal| A small amount of clean water around the outlet on the tub bottom at the back of the tub keeps the water seal lubricated
Plastic items got painted| Tomatoes, carrots ketchup, etc. contain natural dyers. It is the reason of coloring| Quantity of a washing-up liquid or bleaching effect for this purpose are too insignificant Apply more washing-up liquids (Section see „Detergent dispenser”). The painted details any more will not get former color

Fault codes

distributary valve
E9| Blocking of the control panel sensor buttons| Outside items or water on the sensors. Remove all the items, wipe the panel.
Ec| Washing control system fail| PCB or motor fail
Ed| Failure of communication between main circuit board with display circuit board| Open circuit or break wiring for the communication

WARNING!
In case of an overflow, cut off the main water supply before calling the service centre. If there is some water left in the bottom tub caused by overfilling or slight leakage, the water should be removed before restarting the dishwasher.

RESPECT FOR THE ENVIRONMENT

The documentation provided with this oven has been printed on chlorine free bleached paper or recycled paper to show respect for the environment.
The packaging has also been designed to avoid environmental impact. Packaging material is ecological and can be re-used or recycled.
By recycling the packaging, you will help save raw materials as well as reducing the bulk of domestic and industrial waste.

Disposing of the packaging
Please dispose of the packaging that came with your appliance in an environmentally friendly way. Recycling in this way saves on resources and cuts down on waste.

Disposing of old appliances
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

WARRANTY TERMS FOR HOME APPLIANCES

1. The warranty for a broken part is valid for the full period of 24 months from the day of purchase.
2. The manufacturer only covers the servicing in the event of a manufacturer’s fault, such as but not limited to: inappropriate design, faulty installation by technician, defective materials.
3. This warranty applies only to products used for the following purposes: non-commercial, personal, family, residential or household. For anything outside of these purposes, the warranty is only valid for 4 months from the date of the product purchase.
4. Repairs that qualify under this warranty are completely free including the cost of labour and materials, transportation is determined by the relevant Kaiser service centre.
5. Any questions or queries on the quality of the product will be considered only after our service company has examined the product. Conclusions will only be reached based on the outcome of a service report.
6. The product will only be replaced within the warranty period if the service expert concludes that the product cannot be repaired or if the same product requires parts changed three times in total within the warranty period.
7. In case of unnecessary or unjustified demands for customer service, we charge the usual time and transportation fees for our service. Before you contact our customer service, please check whether it’s a genuine product defect or rather faulty handling of the device. Please take time to communicate with the relevant Kaiser service center.
8. Installation of the device should only be carried out by qualified professional persons. The customer is required to provide appropriate justification. Otherwise there is no warranty claim.
9. Only the distributor selling the products has the right to replace the defective product with a new one.
10. Liability under this warranty is limited to these above obligations, unless otherwise specified by law.

WARRANTY IS VOID IF :

1. Our products are being damaged or experience some kind of defect from transport damage, due to incorrect installation by other than trained Kaiser technicians or taking improper care of the products, connecting to the wrong power supply, the use of non-recommended cleaning agents and detergents. Any failure to comply with the instructions for operational use or if the product has been repaired or modified or installed by the customer and the serial number changed or removed will not qualify for the warranty terms.
2. Products being serviced by an unauthorized servicing company will not be valid for warranty.
3. Product failures caused by reasons independent of the manufacturer, such as fluctuations in the power supply, external events such as nature or natural disasters, fire, insects or domestic and wild animals will not qualify for the warranty terms.
4. The glass or ceramic glass on a product is broken or defective after installation. In this case the customer will be held liable.
5. Any damage, scratches, cracks and external mechanical faults have been caused during the operation by the customer.
6. The damage of certain parts has been caused by normal wear and tear such as lamps, filters etc.
7. Other external factors caused damage such as adjusting the products and using inappropriate cleaning products.
8. Any other damage caused by mistake of the user and which is not linked to defects caused by the manufacturer will not qualify for the warranty terms.

The ungrounded devices are potentially dangerous.
The manufacturer accepts no liability for damages which have been caused by improper use, incorrect installation, operation, application or maintenance.

PURCHASE MARK :
RODUCT :

Electric cooker| | Fridge/ Freezer|
---|---|---|---
Gas cooker| | Washing machine|
Built-in hob| | Dishwasher|
Built-in oven| | Cooker hood|
Microwave| | Coffee machine|

Model……………………………………………………………
Serial number ………………………………………………
Dealer………………………………………………………….
Phone………………………………………………………….
Date of purchase ………………………………………….

INFORMATION ABOUT INSTALLATION

Installed………………………………………………………………………
Purchaser (name, surname)…………………………………………..
Address, phone……………………………………………………………..
Purchaser’s signature ……………………………………………………
Expert (name, surname)……………………………………………….
Installer………………………………………………………………………
Installer’s signature …………………………………………………….

The product(s) is sold in their original packaging or tested in my presence. Operating Instructions are supplied and explained.
I am satisfied with the appearance and internal features of the product(s).

Purchaser’s signature

ESECO
Service Center – HaushaltsgerS äte
Wienerbergstr. 11/12 A, 1100 Wien, Austria
Tel.: +43 (0) 1 596 7946
Fax.: +43 (0) 1 596 7946 15
E-Mail: office@eseco.at
Internet: www.eseco.at

http://www.elesco-europa.com

WARRANTY CARD

(Nr. indicates the number of the unit, see the back cover of this manual)
This warranty does not limit statutory rights of consumers
Congratulations on the purchase of household appliances of excellent quality!
Please refer to the warranty card and make sure it has been properly filled in and had a shop stamp. In the absence of the stamp and the date of purchase, warranty period commences from the date of manufacturing of the product. Carefully check the appearance of the product, all claims about the product appearance must be notified to the seller at the time of purchasing.
Keep the warranty certificate and the receipt. In the event of the product components incomplete/ missing and or requirement for their replacement, please contact your dealer.
For the installation, connection and all matters relating to the maintenance, contact authorized service centres. Details of authorized service and repair service centres are attached in a separate list.
We reserve the right to make changes in design or manufacturing technology. Those changes do not entail obligation to update or improve the previously released products.

EG Declaration of Conformity

Germany

This is to confirm that all dishwashers

Brand:|
---|---
Type:| S 60 …*

… = model number

• = colour

comply with the regulations of the European Directives.
The conformity of the designated product with:

EN 55014-1:2017
EN 55014-2:2017/A11:2020
EN 55014-2:2015
EN IEC 61000-3-3:2019
EN 61000-3-3:2013/A1:2019
EN 60335-2-5:2015
EN 60335-1:2012/A2:2019
EN 62233:2008
AfPS GS 2019:01 PAK

Berlin, 12.11.2021
N. Liskovoj
Department Manager

The manufacturer declines all responsibility for possible mistakes and typing errors and reserves the right to make in design and construction of our own products those changes which do not touch negative influence upon the qualities and properties without a preliminary notification.

OLAN-Haushaltsgeräte • Berlin • Germany
www.kaiser-olan.de

References

• Europa.com is For Sale | BrandBucket
• Бытовая техника Kaiser - Официальное представительство, интернет-магазин
• ELESCO EUROPA GmbH – Reparatur – Service – Installation – Wartung – Ersatzteile
• ESECO GmbH | Das Netzwerk für maßgeschneiderte Servicelösungen in Österreich
• Kaiser offizielle Webseite – Kaiser offizielle Webseite
• SFG | Société française de garantie
• Universal Service Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>