dji FlyCart 30 Dynamic Aerial Delivery Drone User Guide
- June 1, 2024
- DJi
Table of Contents
dji FlyCart 30 Dynamic Aerial Delivery Drone
Specifications
- Aircraft (Model E2MTR-30A)
- Operating Frequency: 2.4000-2.4835 GHz; 5.725-5.850 GHz
- Transmitter Power EIRP: 2.4 GHz
Product Information
Aircraft Overview
The DJI FlyCart 30 features various components including propellers, motors, electronic speed controller, front LEDs, aircraft arms, binocular vision systems, DJI cellular module, FPV gimbal camera, spotlight, forward and rear phased array radars, parachute, intelligent flight battery, weighing sensor, onboard storage, landing gear, video transmitter antennas, and GNSS antennas.
Remote Controller Overview
The remote controller is an essential part of the DJI FlyCart 30 system and requires proper charging and preparation for use.
Product Usage Instructions
Charging
- Charging the DB2000 Intelligent Flight Battery: Use the C8000 Intelligent Battery Station to charge the DB2000 Intelligent Flight Battery after activation.
- Charging the Remote Controller: Utilize the DJI USB-C Power Adapter (100W) to charge the remote controller. Ensure the internal battery is activated before use.
Prepare for the Remote Controller
- Checking Battery Level: Press once on the power button to check the battery level. Power on/off by pressing and holding the power button.
- Adjusting the Antennas: Lift and adjust the antennas for optimal signal strength.
Prepare for the Aircraft
- Unfolding the Aircraft: Follow the sequence to unfold the frame arms and propellers. Install batteries correctly and activate the aircraft.
Using the On-board Storage
- Flight Manual Take Off/Landing: Control start/stop motors and take off/land using throttle stick movements.
- Control the Aircraft: The default stick mode is Mode 2 where the left controls altitude and heading, and right controls movements.
FAQ
- Q: Can I charge the remote controller with a different adapter?
- A : It is recommended to use the DJI USB-C Power Adapter (100W) to charge the remote controller for optimal performance and safety.
- Q: How do I know if the aircraft is properly activated?
- A : Follow the on-screen instructions in DJI PILOTTM 2 after powering on both the aircraft and remote controller to ensure proper activation.
- Q: What should I do if the battery level LEDs do not flash when charging the remote controller?
- A : Make sure the internal battery of the remote controller is activated by pressing and holding the power button to initiate charging.
Aircraft Over View
- Propellers
- Motors
- Electronic Speed Controller
- Front LEDs
- Aircraft Arms
- Binocular Vision System (
- Binocular Vision System (
- DJI Cellular Module
- FPV Gimbal Camera
- Spolight
- Forward Phased Array Radar
- Parachute
- Intelligent Flight Battery
- Weighing Sensor
- Onboard Storage
- Landing Gear
- Rear Phased Array Radar
- Video Transmitter Antennas
- Rear LEDs
- GNSS Antennas
Remote Controller Overview
- External Antennas
- Touchscreen
- Aircraft Authority Button
- Control Sticks
- Internal Wi Wi-Fi Antennas
- Back/Function Button
- Return to Home (RTH) Button
- Status LED
- Battery Level LEDs
- Internal GNSS Antennas
- Power Button
- 5D Button
- Flight Pause Button
- Reserved Button
- Flight Mode Switch
- Internal Antennas
- microSD Card Slot
- USB-A Port
- HDMI Port
- USB
- USB-C Port
- Battery Release Button
- Battery Compartment
- Rear Cover Release Button
Using FC30
Charging
Charging the DB2000 Intelligent Flight Battery DB2000 Intelligent Flight Battery needs to be activated using C8000 Intelligent Battery Station Station.
Charging the Remote Controller
Use the DJI USB USB-C Power Adapter (100W) to charge the remote controller. The internal battery of the remote controller must to be charged to activate before using for the first time. The battery level LEDs start to flash to indicate the internal battery is activated and charging started.
The remote controller cannot be powered on before activating the internal battery.
Prepare for the remote Controller
Checking Battery Level
Press once on the power button to check the battery level when powered off.
Powering On/Off
Press once, press and hold on the power button to power on/off the remote controller. Follow the on on-screen instructions to activate the remote controller before using for the first time.
Adjusting the Antennas
Lift and adjust the antennas. The strength of the remote controller signal is affected by the position of the antennas.
Prepare for the Aircraft
Unfold the aircraft
- a. Unfold the M3 and M4 frame arms before unfolding the M1 and M2 frame arms. Lock the arm lock for each frame’s arms.
- b. Remove the propeller holder.
- c. Unfold the propellers
Installing the Intelligent Flight Battery
Install the two batteries as shown. Press down the battery until you hear two
two-click sounds in sequence.
Checking the Battery Level
Check the battery level: press once on the power button.
Power on
on/off : press once, and press and hold the power button.
Activating the Aircraft
Power on the aircraft and remote controller, launch DJI PILOT TM 2, and follow the on on-screen instructions to activate the aircraft.
Using the On -board Storage
Flight
Manual take off off/lan ding
- Start Start/stop motors
- Take off : push the throttle stick up to take off
- Landing : pull the throttle stick down to land.
Control the Aircraft
The default control stick mode is Mode 2. The left control stick controls the altitude and heading of the aircraft while the right control stick controls the forward, backward, and sideward movements.
Specifications
- Aircraft (ModelModel ： E2MTRE2MTR-30A30A)
- Operating Frequency: 2.4000 2.4000-2.4835 GHz; 5.725 5.725-5.850 GH GHz
- Transmitter Power （EIRP）: 2.4 GHz: <33 dBm (FCC), <20 dBm (SRRC/CE/MIC) 5.8 GHz: <33 dBm (FCC), <23 dBm (SRRC), <14 dBm (CE) RTK/GNSS
- Operating Frequency RTK : GPS L1/L2, GLONASS F1/F2, BeiDou B1I/B2I/B3I, Galileo E1/E5b, QZSS L1/L2 GNSS GNSS ：GPS L1, GL ONASS F1, BeiDou B1I, Galileo E1, QZSS L1
- RTK/GNSS
- Operating Frequency RTK : GPS L1/L2, GLONASS F1/F2, BeiDou B1I/B2I/B3I, Galileo E1/E5b, QZSS L1/L2 GNSS GNSS：GPS L1, GL ONASS F1, BeiDou B1I, Galileo E1, QZSS L1
- Operating Temperature: -20℃ to 45℃
- Forward Phased Array Radar Radar（ModelModel： RD241608RFRD241608RF）
- Operating Frequency: 24.05 24.05-24.25 GHz (NCC/FCC/MIC/KC/CE)
- Power Consumption : 23 W
- Transmitter Power Power（EIRP）: <20 dBm (NCC/MIC/KC/CE/
- Operating Voltage: DC 15 V
- Operating Temperature: -20℃ to 45℃
- Rear Phased Array Radar Model： RD241608RBRD241608RB）
- Operating Frequency : 24.0524.05-24.25 GHz (NCC/FCC/MIC/KC/CE)
- Power Consumption : 18 W
- Transmitter Power Power（EIRP ）: <20 dBm (NCC/MIC/KC/CE/
- Operating Voltage : DC 15 V
- Operating Temperature : -20℃ to 45℃
- Remote Contorller Model ：RM700BRM700B）
- Internal Battery: Li -ion (6500 mAh@7.2 V)
- O3
- Operating Frequency: 2.40002.4000-2.4835 GHz; 5.725 5.725-5.850 GHz
- Transmitter Power （EIRP）: 2.4 GHz: <33 dBm (FCC), <20 dBm (CE/SRRC/MIC) 5.8 GHz: <33 dBm (FCC), <14 dBm (CE), <23 dBm (SRRC)
- Wi -Fi :
- Protocol : Wi -Fi
- Wi-Fi 6 Operating Frequency 2.40002.4000-2.4835 GHz; 5.150 5.150-5.250 GHz; 5.725 5.725-5.850 GHz Bluetooth
- Protocol: Bluetooth 5.1
- Operating Frequency: 2.40002.4000-2.4835 GHz
- Transmitter Power （EIRP）: <10 dBm
Compliance Information
FCC Compliance Notice
Supplier’s Declaration of Conformity
- Product name: DJI FlyCart 30
- Model Number: E2MTRE2MTR-30A
Responsible Party:
DJI Research LLC Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com
We,
DJI Research LLC, being the responsible party, declares that the above-
mentioned model was tested to demonstrate compliance with all applicable FCC
rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. This transmitter must not be located or operating in conjunction with any other antenna or transmitter.
ISED Compliance Notice
CAN ICES-003 (A) / NMB-003(A)
This device contains license licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license license-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>