Keychron Q2 Max Wireless Mechanical Keyboard User Manual

**Keychron Q2 Max Wireless Mechanical Keyboard User Manual

**

Fully Assembled Version

Keyboard
1x Fully Assembled Keyboard
Including
1x Aluminum Case
1xPCB 1xPC Plate.
1x Sound Absorbing Foam
1 IXPE Foam 1 PET Foam
1x Latex Bottom Pad
1x Bottom Case Acoustic Foam
1x Bottom Case PET Foam
14x Gaskets (10 Installed and
4 n the Box)
4 sets x Stabilizers
1 set x Keycaps (PBT Double-shot )
1 set x Switches

Cable
1xType-C to Type-C Cable
1 Type-A to Type-C Adapter
1x Extension Adapter for Receiver

Receiver

1x Type-A 2.4 GHz Receiver
Tools
1xKeycap & Switch Puller 1x Screwdriver 1 Hex Key

Barebone Version

Keyboard Kit
1x Keyboard Kit (Without Keycaps & Switches)
Including
1x Aluminum Case 1x PCB
1x PC Plate
1x Sound Absorbing Foam
1x IXPE Foam
1x PET Foam
1x Latex Bottom Pad
1x Bottom Case Acoustic Foam
1x Bottom Case PET Foam
14x Gaskets (10 Installed and 4 in the Box)
4 sets x Stabilizers

Cable
1x Type-C to Type-C Cable
1x Type-A to Type-C Adapter
1x Extension Adapter for Receiver

Receiver
1x Type-A 2.4 GHz Receiver
Tools
1x Keycap & Switch Puller
1x Screwdriver
1 Hex Key

Quick Start Guide

If you are a Windows user, please find the appropriate keycaps in the box, then follow the instructions below to find and replace the following keycaps.
Mac/Windows

1.  Switch o The Right System
   Please make sure the system toggle on the topleft comer has been switched to the same system as your computer’s operating system.
   

2. Connect 2.4 GHz Receiver
   Connect the 2.4 GHz receiver to the device USB port.
   
   Switch toggle to 2.4 GHz mode

G=24GHz

Note: For the best wireless experience, we recommend using the extension adapter for receiver and putting the receiver somewhere on your desk close to your keyboard for a low rate of latency and fewer signal interferences.

3. Connect Bluetooth

Switch toggle to Bluetooth

Press fn1 + Q for 4 seconds) and pair with device named Kechror Q2 Max

4. Connect Cable
   
   Switch toggle to Cable

5. The VA Key Remapping Software
   Please visa use kiap to usethe online VIA software tore map the keys If the VIA cannot recognize your keyboard, pleas reach our upper to get the instruction,
   
   “The online VIA software can only run on the latest version of Chrome, Edge, and Opera browsers yet. “VIA only works when the keyboard is connected by wire to the computer.

6. The Layers
   There are five layers of key settings on the keyboard.
   The layer 0 is for the Mac system.
   The layer 1 is for the Windows system.
   The layer 2 is for the Mac Multimedia keys.
   The layer 3 is for the Windows Multimedia keys. The layer 4 is for function keys.

If your system toggle is switched to Mac, then the layer 0 will be activated.

If your system toggle is switched to Windows, then the layer 1 will be activated.

7. Multimedia Key and Function Key
   Multimedia keys
   
   Function keys
   
   In order to get Multimedia Key, you need to press fn1 and Key.
   In order to get Function Key, you need to press fn2 and Key.

8. The Backlight
   Press fn1 + A to change the lighting effect
   
   Press fn1 + caps lock to turn the backlight on/off
   

9. Adjust The Backlight Brightness
   Press fn1 + S to increase the backlight brightness
   
   Press fn1 + X to decrease the backiight brightness
   

10.  Adjust The Backlight Speed
    Press fnl + G to increase the light effect speed
    
    Press fn1 + B to decrease the light effect speed
    

11. Warranty

The keyboard is highly customizable and easy to be rebuilt. If anything goes wrong with any of the keyboard components of keyboard during the warranty period, we will only replace the defective parts of the keyboard, not the whole keyboard.

12. Factory Reset
    

Troubleshooting? Don't know what's going on with the keyboard?

1. Download the right firmware and QMK Toolbox from our website. 2. Unplug the power cable and switch the keyboard to Cable mode. 3. Remove the space bar keycap to find the reset button on the PCB. 4. Hold the reset key first, then plug the power cable into the keyboard. Release the reset key after 2 seconds, and the keyboard will now enter DFU mode. 5. Flash the firmware with the QMK Toolbox. 6. Factory reset the keyboard by pressing fn2 + J + Z (for 4 seconds). *Step by step guide can be found on our website.

Q2 MAX WIRELESS MECHANICAL KEYBOARD SPECIFICATIONS

Number of keys: 66
Switch type: Mechanical
Battery: 4000mAh Wireless working time (RGB): Up to 100 hours (Lowest brightness)
Charging time: Around 5 hours
Charging port: USB Type-C
Mode: 2.4 GHz/Cable / Bluetooth
Wireless operating distance: Within 10 meters (open space)
Name of Bluetooth device: Keychron Q2 Max

Operating environment: -10 to 50°C Technical specifications can be subjected to change without notice, we apologize for any inconvenience caused.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>