Keychron Q1 Max Wireless Mechanical Keyboard User Manual
- June 1, 2024
- Keychron
Table of Contents
Keychron Q1 Max Wireless Mechanical Keyboard
Fully Assembled Version
Keyboard
- 1x Fully Assembled Keyboard
Including
- 1x Aluminum Case
- 1x PCB
- 1x PC Plate
- 1x Sound Absorbing Foam
- 1x IXPE Foam
- 1x PET Foam
- 1x Latex Bottom Pad
- 1x Bottom Case Acoustic Foam
- 1x Bottom Case PET Foam
- 14x Gaskets (10 Installed and 4 in the Box)
- 4 sets x Stabilizers
- 1 set x Keycaps (PBT Double-shot)
- 1 set x Switches
Cable
- 1x Type-C to Type-C Cable
- 1x Type-A to Type-C Adapter
Receiver
- 1x Type-A 2.4 GHz Receiver
Tools
- 1x Keycap & Switch Puller
- 1x Screwdriver
- 1x Hex Key
Barebone Version
- Keyboard Kit
- 1x Keyboard Kit (Without Keycaps & Switches)
Including
- 1x Aluminum Case
- 1x PCB
- 1x PC Plate
- 1x Sound Absorbing Foam
- 1x IXPE Foam
- 1x PET Foam
- 1x Latex Bottom Pad
- 1x Bottom Case Acoustic Foam
- 1x Bottom Case PET Foam
- 14x Gaskets (10 Installed and 4 in the Box)
- 4 sets x Stabilizers
Cable
- 1x Type-C to Type-C Cable
- 1x Type-A to Type-C Adapter
Receiver
- 1x Type-A 2.4 GHz Receiver
Tools
- 1x Keycap & Switch Puller
- 1x Screwdriver
- 1x Hex Key
Quick Start Guide
- If you are a Windows user, please find the appropriate keycaps in the box, then follow the instructions below to find and replace the following keycaps.
Mac / Windows
Connect 2.4 GHz Receiver
- Note: For the best wireless experience, we recommend using the extension adapter for the receiver and putting the 2.4 GHz receiver somewhere on your desk close to your keyboard for a low rate of latency and fewer signal interferences.
Connect Bluetooth
- Press fn + 1 (for 4 seconds) and pair with a device named Keychron Q1 Max
Connect Cable
The VIA Key Remapping Software
- Please visit use via.app to use the online
- VIA software to remap the keys.
- If the VIA cannot recognize your keyboard, please reach our support to get the instruction.
- The online VIA software can only run on the latest version of Chrome, Edge, and Opera browsers.
- VIA only works when the keyboard is connected by wire to the computer.
The Layers
- There are four layers of key settings on the keyboard. Layer 0 and layer 1 are for the Mac system. Layer 2 and layer 3 are for the Windows system.
- If your system toggle is switched to Mac, then layer 0 will be activated.
- If your system toggle is switched to Windows, then layer 2 will be activated. Remember that if you are using it in Windows mode, please make changes to layer 2 instead of the top layer (layer 0).
- This is a common mistake people are making.
The Backlight
- Press fn + Q to change the lighting effect
- Press the fn + tab to turn the backlight on/off
Adjust The Backlight Brightness
- Press fn + W to increase the backlight brightness
- Press fn + S to decrease the backlight brightness
Adjust The Backlight Speed
- Press fn + T to increase the light effect speed
- Press fn + G to decrease the light effect speed
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>