GPS Tracker 303FG-2-V3.4 GPS Locator User Manual

GPS Tracker 303FG-2-V3.4 GPS Locator

Specifications

Product Using Instruction

• Hardware Description
  • The device features GPS/POWER/GSM status lights for easy monitoring.
• Terminal Installation
  • Please ask a qualified engineer to install the device.
  • Ensure the installation environment has good GSM and GPS signals.
  • Avoid installation in dusty and humid environments.
• Device Status Light
  • Red light: Indicates charging status. Green light: Indicates GSM network signal status. Blue light: Indicates GPS signal status.
  • This GPS Tracker Supports Mobile apps, Web Server Platforms and SMS for Management in Multiple Ways
• Mobile APP
  • To use the mobile app:
  • Scan the QR code or search for “BAANOOL IOT” on Google Play or App Store to download the app.
  • Register and log in to the app using a new account.

FAQs

Q: Can the GPS locator be used in all types of vehicles?

A: The GPS locator is designed for use with vehicles that have a power supply of 12V-24V.

Q: How do I know if the GPS signal is strong?

A: The blue light on the device will flash three times per second when the GPS signal is very good.

Q: What should I do if the device is still offline after binding?

A: You may need to set the APN, username, and password according to the manual if the device remains offline after binding.

Specifications

Hardware Description

Terminal Installation

1. Please ask a qualified engineer to install it.
2. The installation environment should ensure that the GSM and GPS signals are good
3. Please do not install it in a dusty and humid environment.
4. Find the 12PIN wiring harness provided with the product, insert it into the corresponding wiring hole of the product, and connect to the original car circuit as shown in the following Wiring
   • Diagram:
5. The pink wire can be connected to the original car alarm horn or the alarm horn purchased together.
6. Understand that the vehicle door trigger type is a positive trigger or a negative trigger. Connected to the green wire if it is a positive trigger, and connected to the blue wire if it is a negative trigger.
7. Please install the SOS button where the driver can touch it.
8. SIM card installation
   • Please use the included screwdriver to open the case to insert the SIM card. If you intend to expand the storage space, then please insert micro SD and then assemble the case.
   • Please be sure to confirm that the SIM card network frequency band is the network frequency band supported by the device. Caller ID must be turned on and the PIN code must be turned off. The call forwarding function cannot be turned on.
9. After inserting the SIM card, connect the positive and negative (red and black) wires of the power supply to the 12V or 24V power supply of the car. Wait for the device to work normally After 1 minute of power-on, and then turn on the Backup battery switch.

Device Status Light

• Red light: Always on when charging, and turns off after being fully charged. Red light flashes quickly when the battery is low.
• Greenlight: Flashes every 1 second when the GSM network signal is normal, flashes every 3 seconds when working in GPRS mode; always on when no GSM network.
• Blue light: Flashes every 1 second when GPS signal is normal; flashes 3 times per second when GPS signal is very good and turns off if lost fixed to satellites.

This GPS Tracker Supports Mobile apps, Web Server Platforms and SMS for Management in Multiple Ways

• If you use the APP and web platform, you need a sim card to open a data plan or use a data card.
• If you use SMS, you need a SIM card to enable SMS, voice calls, and caller ID.

Mobile APP

Scan the QR code to download APP

• Google Play、App Store search “BAANOOL IOT” to download it

Register

• Open BAANOOL IOT, register a new account and log in, Choose “BAANOOL car “to enter it.

Bind Device

• Click the ‘Add Device’ button on the home page and scan the IMEI number to bind a new device.
• Note that the IMEI number is attached to the side of the device, and the IMEI of the device can also be manually entered for binding.

Using tracker

• Under normal circumstances, the device can automatically select the APN, username and password without setting it.
• If the device is still offline after 3 minutes of binding, you need to set the APN username and password according to 10.17 and 10.18.
• After the device comes online, you can view and manage the device.

BAANOOL IOT’s Web Version

• Open www.baanooliot.com, the login account name and password are the same as the phone app’s.

Mobile APP and BAANOOL IOT’s Web

Positioning strategy

• You can click the positioning button to select the working mode and positioning strategy.
• When stationary, you can set a longer period to report location information (such as 1 hour), and when it moving, you can set a short period to report location information frequently (such as 10 seconds).
• When the tracker moves, the movement trajectory will be displayed.

Working mode

according to the set motion/stationary intervals. The device is online in real time by default and reports its location at intervals of 10 seconds of movement and 1 hour of inactivity.
Smart mode| Offline when stationary (phone calls, text messages, and alarms can trigger the device to go online. After SOS, door opening alarms, and ACC alarms are triggered, the device will be online in real time until the alarm is lifted). Wake up and go online when in motion. Regardless of whether it is stationary or moving, the device will report at the set interval. Location.

Positioning interval

Playback
You can click the playback button to view the historical track record

Remote immobilizing

• Delayed immobilizing, Immobilizing immediately, Resume fuel and power supplying

Arm/ Disarming

• Arm, silent arm, disarm.

Alarm function in arming state

• Door open alarm
  • When the system is in the armed state and the car door is illegally opened, the device will trigger the door open alarm and the alarm siren will beep for 20 seconds.
  • If the door has been illegally opened, the alarm siren will beep continuously at 20-second intervals. Disarming can stop the alarm.
• ACC alarm
  • When the tracker is in the armed state, turn the starter key to the ACC ON position or start the vehicle directly.
  • The device will trigger the ACC ignition alarm and the alarm siren will beep for 20 seconds.
  • If it is in the illegal ignition state, the alarm siren will beep continuously at 20-second intervals. Disarming can stop the alarm
• Shock alarm
  • When the tracker is in an armed state, a shock alarm will be triggered when the device moves or vibrates.
  • The shock alarm will only be triggered once within 3 minutes. The alarm siren will beep for seconds for the first time within three minutes.
  • The alarm siren will beep for 5 seconds for the second time. The siren will beep for 10 seconds for another trigger of shock alarm

Other alarm functions

• Low battery alarm
  • When the tracker’s built-in battery voltage is close to 3.55V, the tracker will send a low battery alarm every 15 minutes, a total of 2 times.
• External power disconnection alarm
  • This function is turned on by default. When the external power supply is disconnected, the device will send an external power disconnection alarm.
• SOS Alarm
  • Press the SOS button for 3 seconds and the device will send an SOS alarm.
• Geo fence
  • After multiple electronic fences are set up on the APP or platform, the Geo fence alarm will be triggered when the device enters or leaves the set fence.
• Movement alarm
  • Draw a circle with the current location of the tracker as the centre. Once the tracker exceeds the radius, a movement alarm will be triggered.
• Over speed alarm
  • After setting the speed value, an overspeed alarm will be triggered when the device speed exceeds the set threshold.
• Fuel Alarm
  • When the vehicle’s fuel consumption exceeds the normal standard while the vehicle is running, or there is fuel leakage or fuel stealing when the vehicle is stopped, the GPS will trigger an oil theft and oil leakage alarm, and the alarm horn will sound for 20 seconds.
• Listen
  • Listen for 15 seconds per request
• Other function settings
  • You can control the device to stop alarming, check the sim card balance, reset the device, restore factory settings, set shock sensitivity, authorization number, times of alarms, time zone, external power on/off, Oil volume zero adjustment/full adjustment, smart angle updating settings, tracker password, check device details, operation records, and installation information.

Remote controller

Remote controller（For G model）

If you prefer to use the mobile APP and web platform to manage your device, you do not need to pay attention to the following content.

SMS functions

• GPRS and SMS work at the same time by default, If you only use SMS to manage the device, it is recommended to turn off GPRS by referring to the command of 10.21 to save power and traffic.

Attention：

• When reading this user manual, you will notice that we have used “+” and “space” between some words;”+” between two words means they should be written together as one word and “space” between two words means you should leave one character space between two words.

Changing Password

• Command: password+old password+space+new password, Response: password ok
• The default password is 123456, which must be changed when using it for the first time.

Authorization

• Command: admin+password+space+mobile phone number, Response: admin ok
• Cancel  noadmin+password+space+authorization number,
• Response: no admin ok Call the tracker 10 times in succession, the number will be authorised automatically as the first number and the tracker response “add master ok” Up to 5 numbers can be set and authorized, and only authorized number can receive an alarm message.

Single Tracking

• Command: position+password, tracker reply with the location information and click the link to view the device location on the map.
• Make a call to the tracker, and the tracker will automatically hang up and reply with a positioning message.
• If there aren’t any authorized numbers set up, it will reply to all calls with a location report; if there are authorized numbers set up, then it will not respond when an unauthorized number calls it.

Positioning strategy Working mode

• Real-time online: online+password, GSM always online, the location can be queried at any time, and whether the device is stationary or moving, the location will be reported at set intervals. Smart mode: sleep+password, the device sleeps when it is stationary (phone calls, SMS, and alarms can trigger the device to go online. After SOS, door opening alarms, and ACC alarms are triggered, the device will be online in real-time until the alarm is cleared). It wakes up when moving, whether it is stationary or moving. The device will report its position according to the set positioning intervals.

Positioning interval

• Command: fix+020s+002h+005n+password, tracker will report at 20 seconds interval when the device is moving, and 2 hours when it is stopped, 005n means limited to 5 times of positioning, ***n means unlimited times.
• Cancel: nofix+password, Response: nofix ok

Remote immobilizing

• Delayed immobilizing
  • Command: stop+password. When the current speed of the vehicle is greater than 20km/h, the command will not be executed immediately. it will be executed only after the vehicle speed is less than 20Km/h.
• Immobilizing immediately
  • Command: quickstop+password, no matter whether the vehicle speed is greater than 20km/h, the command will be executed immediately.
• Resume fuel and power supplying
  • Command: resume+password, restore fuel and power supply.
• Arming/disarming
  • Arming: arm+password, Response： Tracker is activated, and the vehicle terminal enters the armed state. If the vehicle is in the ignition state (i.e. ACC is ON), it cannot enter the armed state, and then reply “set up fail! pls turn off ACC”.
  • Silent arming: silent+password, Response： silent ok! The terminal enters the silent arming state. After the alarm is triggered, the siren does not sound, but an alarm text message will be sent to the authorised number.
  • Disarming: disarm+password, response: Tracker is deactivated, After disarming, the door, shock sensor and ACC alarm will be deactivated.
• Alarm function in arming state Door Opening Alarm
  • When the door is opened in the arming state, the tracker will send an SMS notification “Door alarm+latitude & longitude” to authorized numbers. The siren will beep for 20 seconds, and if the door is still open, then the siren will beep for another 20 seconds with 20 20-second pause, disarming to quit the alarm.
• ACC Alarm
  • When the tracker is in the armed state, turn the starter key to the ACC ON position or start the vehicle directly, it will send “ACC alarm + latitude/longitude” to authorized numbers and the siren will sound for 20 seconds.
  • And if the ignition is still on, then the siren will beep for another 20 seconds with 20 20-second pause, disarming to quiet the alarm.
• Shock Alarm
  • When the tracker is in the armed state, when the device moves or vibrates, it will send an SMS notification “Sensor alarm + latitude and longitude” to the authorized number.
  • The vibration alarm will only be sent once within 3 minutes. The siren will beep for 5 seconds for the first time within three minutes of the vibration alarm.
  • The siren sounds for 5 seconds and then sounds for 10 seconds.
  • Vibration sensitivity defaults to level 2, which can be set to 1, 2, or 3.
  • Command: sensitivity+password+space+2

Other alarms

• Low battery alarm: It is activated by default, when the battery voltage is close to 3.55V, the tracker will send the message “low battery + latitude & longitude” to authorized numbers 2 times at 15-minute interval.
• Turn off: lowbattery+password+space+off, response: low-battery off ok
• Turn on: lowbattery+password+space+on, response: low battery on ok

External power disconnection alarm

It is activated by default. When the external power supply is disconnected, the device will trigger a power disconnection alarm.

• Turn on: extpower+password+space+on, response: ext power on ok
• Turn off: extpower+password+space+off, response: ext power off ok

SOS alarm

• Press the SOS button for 3 seconds (For model G, press a key on the remote control), the device will trigger the SOS alarm.

Movement alarm

• SMS Command: move+password+space+radius, response: move ok
• Cancel: nomove+password, response: nomove ok

Draw a circle with the current position of the device as the centre. Once the device exceeds the radius, the device will trigger a movement alarm.

Over speed alarm

• SMS Command: speed+password+space+speed value, response: speed ok
• Cancel: nospeed+password, response: no speed ok

When the speed exceeds the set speed value, the device will trigger over speed alarm.

Fuel Alarm

When the vehicle’s fuel consumption exceeds the normal standard while the vehicle is running, or there is fuel leakage or fuel stealing when the vehicle is stopped, the tracker will send “oil: ××%+latitude & longitude” to the authorized numbers. The siren will sound for 20 seconds. For reasons such as different fuel tank heights and specifications, tracker needs to set the proper height to zero and full values to read the correct percentage value.

• Calibrate 0%: when the fuel tank is empty， send the command “oilzero+password” to the device. After receiving it, the device will automatically calibrate the zero and respond “oilzero ok!”. At this time, the oil value is 0%.
• Calibrate 100%: Then fill up the oil tank, and then send the command “oilfull+password” to the device. After receiving it, the device will automatically calibrate 100% and respond “Oil full ok!” At this time, the oil value is 100%

Configure times of alarm

The times of SOS, power disconnection, oil, door, and ACC alarm sending can be set.

• Command: xtime+password+times value, response: xtime ok! Send once by default.

Listen

The default mode is “Track” mode, dial the device, reply position

• Command: listen+password, switch to Listen mode, dial the device, enter call
• Command: tracker+password, restore to Track mode

ACC ON/OFF Alert
This function is OFF by default. If the tracker detects an “ignition on” signal from the ACC wire (white wire), the tracker will send “ACC on+latitude& longitude” to authorize the number to tell you the vehicle has been started. When detect the “ignition off” signal, it will send “ACC off+ latitude & longitude” to tell you the vehicle has been stopped.

• Turn on： ACC+password，response：ACC ok
• Turn off： noACC+password，response：noACC ok

SIM Card Balance Enquiry Way1

• Command: balance+password+space+operator number+space+code The device will forward the received text message from the operator to the sender of the command

Way 2

• Command: forward+password+space+operator number
• When the network operator sends a text message to remind you to top up your sim card, the tracker will forward the notification message to the authorized number

Check Status

• Command: check+password, Response: Battery, GPS signal, GSM signal, GPRS status, APN, UP, IP, Port etc.

IMEI Inquiry

• Command: imei+password, response: the imei of your device.

Time zone setting

• The device automatically synchronizes the local time zone. If the time is wrong, you need to set the time zone.
• Command: time+space+zone password+space+time zone, reply: time ok

Reset Hardware

• Command: reset+password, response: reset ok

APN Setting

• Command: apn+password+space+local apn, response: apn ok
• Settings are only required when using the APP and web version

Configure user name and password of GPRS network

• Command: up+password+space+user+space+Password, response: up ok
• Settings are only required when using the APP and web version

Configure server IP/DNS and port

• Command: adminip+password+space+IP/DNS+space+port, reponse: adminip ok
• No setup is required to use our BAANOOL IOT server,

TCP / UDP switch

• Command: tcp+password, response: tcp ok
• Command: udp+password, response: udp ok
• No setup is required to use our BAANOOL IOT server

SMS mode

• Command: SMS+password, response: sms ok
• The device’s default mode is GPRS mode, if the user prefers to use SMS to manage the device, please use this command to close GPRS mode

GPRS Mode

• Command: gprs+password, response: GPRS ok

Initialization

• Command: begin+password, response: begin ok
• All command settings will return to default factory settings

Accessories

Cautions

Please be sure to follow when using:

1. Keep the tracker used in a dry environment. The humid environment can easily damage internal circuits.
2. Please do not put it in a dusty environment.
3. Do not put the tracker in overheated or overcooled places.
4. Handle carefully. Don’t vibrate or shake it violently.
5. Please clean with a dry cloth, do not use chemicals and detergents.
6. Please do not disassemble the device; this may lead to internal circuit failure.
7. Please read the user manual carefully before installation and operation, and understand the voltage range. Otherwise, it won’t work properly or damage the tracker.

Troubleshooting

No GSM signal

| Check whether the SIM card is put in place; Whether the SIM card is a GSM network SIM card; Don’t turn on the PIN code; Call forwarding cannot be opened.
No GPS signal| The device needs to be in an unobstructed position to ensure that it can receive GPS signals normally.
No response for SMS command| The password is incorrect or the format of the SMS command is incorrect.
No response for a call/No alarm notification message| The authorization number is incorrect or no authorization number is set.
Fail to stop the engine| Please check whether the engine stop wiring is connected correctly?
Remote control cannot be used| Turn off tracker, and turn it on to program the remote control again.

Thank you very much for purchasing our GPS locator. The user manual will explain in detail how to operate this product. Therefore please be sure to read it carefully before using the product. Subject to change without prior notice, each change will be published in the latest product sale. The manufacturer assumes no legal responsibility for errors and omissions in this manual.

References

• BAANOOL IOT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>