Sunnydaze DECOR GSI-806 49 Inch Stacked Slate Outdoor Water Fountain Instruction Manual
- June 2, 2024
- Sunnydaze DECOR
Table of Contents
Sunnydaze DECOR GSI-806 49 Inch Stacked Slate Outdoor Water Fountain
Product Information
Specifications:
- Product Name: Stacked Slate Freestanding Floor Fountain
- Model Number: GSI-806
- Warranty: 1 year
Product Usage Instructions
Assembly:
-
Remove the bolts and washers from Basin (B).
-
Connect Electric Submersible Pump (C) to Fountain Body (A).
-
Gently place the fountain body onto the basin, ensuring the
pump power cord runs out of the groove in the back of the basin. -
Secure the fountain body to the basin using the washers and bolts.
-
Rinse Decorative Stones (D) with clean water. Arrange stones on the bottom of the fountain body.
-
Fill the basin with approximately 3 gallons of water to keep the pump fully submerged during operation.
-
Plug the power cord into a properly grounded GFCI outlet.
Important Notes:
Use care when unpacking and assembling this fountain. Check the basin for
leaks before assembling. Handle the water tubing with care as detaching it
will void the warranty. Slate is a natural product; variations are expected.
Maintenance:
To maintain the fountain, periodically check for leaks, clean the pump and
basin, and ensure the water level is adequate for proper pump operation.
FAQ
-
Q: What should I do if I notice leaks in the basin?
A: Contact an expert at your local hardware store for an appropriate sealant and carefully follow the manufacturer’s instructions to seal the leak. -
Q: Can I use chemical treatments or protective coatings on the fountain?
A: No, as these can void the warranty. The one-year warranty does not cover damages caused by such treatments.
STACKED SLATE FREESTANDING FLOOR FOUNTAIN GSI-806
Review all assembly and care information before using this product. Save this
manual for future reference. Select a smooth, level surface to place the
fountain. Assemble components on a soft, clean surface to avoid scratching or
damaging the finish.
- Purchase Date:
- Order/Customer Reference Number:
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the
quality of the items we sell. Replacement parts or products will be sent at
our discretion within the 1-year warranty period. Proof of purchase, with the
date of purchase as well as photos of the merchandise defect, must be
provided. Photos are used to determine the cause of defects and for future
quality control. Register your warranty at
https://tiny.cc/SunnydazeWarranty.
If you have any questions, comments, or concerns, feel free to contact us by
phone at 833-982-1977, by email: at
[email protected],
or via our Contact Us page at https://tiny.cc/SunnydazeContact.
Inspect packaging to ensure all parts are accounted for before disposing of packing materials.
2-PERSON ASSEMBLY RECOMMENDED
Parts List
| No. | Parts | Qty. |
|---|---|---|
| A | Fountain Body | 1 |
| B | Basin | 1 |
| C | Electric Submersible Pump | 1 |
| D | Decorative Stones | 1 PK |
Tools Required
Tools Required (not included)
IMPORTANT NOTES:
Use care when unpacking and assembling this fountain. Check the basin for
leaks before assembling the fountain. The sealant used to join the slate
pieces can become cracked if the fountain is not handled with care. Simply add
water and wait to see if water begins to leak. If a leak is discovered,
contact an expert at your local hardware store for an appropriate sealant and
carefully follow the sealant manufacturer’s instructions to seal the leak. The
water tubing is built into the decorative top. Take care when handling the
water tube; detaching the water tube from the decorative top will damage the
fountain and void the product warranty. Slate is a natural product; the colors
and texture of each piece are unique, and no two fountains will look the same.
Variations in the slate colors and textures are not a cause for return. Each
fountain is cut from large slabs of slate. Spalling (flaking) may occur
naturally over time, and/or if slate is dropped.
WARNING:
THE ONE-YEAR WARRANTY DOES NOT COVER DAMAGES OR DEFECTS CAUSED BY THE
APPLICATION OF CHEMICAL TREATMENTS, PROTECTIVE COATINGS, OR SEALANTS.
ASSEMBLY
- Remove the bolts and washers from Basin (B).
- Connect Electric Submersible Pump (C) to Fountain Body (A).
- Gently place the fountain body onto the basin, ensuring the pump power cord runs out of the groove in the back of the basin.
- Secure the fountain body to the basin using the washers and bolts that were removed during Step 1.
- Rinse Decorative Stones (D) with clean water. Gently arrange stones on the bottom of the fountain body.
- Fill the basin with enough water to keep the pump fully submerged during operation, approximately 3 gallons.
- Plug the power cord into a properly grounded GFCI outlet.
NOTE:
When first plugged in, there may be air trapped in the pump. It may take
several moments for trapped air to escape, allowing water to flow.
Care & Maintenance
- For outdoor use only. Some splashing is normal; adjust the flow rate on the pump if the water rate is too high.
- Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn out the motor.
- Some climates and weather conditions increase water evaporation, requiring water to be added more frequently. Frequently check water levels during times of high temperatures, wind, and long-term exposure to direct sunlight to ensure the pump does not run dry.
- Only use water in this fountain. Distilled water will help prevent mineral buildup but is not required. Tap water is okay to use, but avoid heavily chlorinated water as it may damage the fountain and pump.
- Periodically change the water to keep the water, fountain, and pump clean. Remove scale and buildup regularly.
- DO NOT use harmful additives such as bleach, chlorine, etc.
- DO NOT use anything abrasive to scrub the fountain.
- DO NOT use a pressure washer.
- Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump.
- Take care when handling the pump; only pick it up by the body of the pump, never the power cord.
- During freezing weather, drain the fountain, disconnect the pump, and store it indoors; allowing ice to form may damage the fountain in such ways as, but not limited to, fountain cracking and/or permanent pump damage.
Troubleshooting
- If water is not flowing within several moments of the fountain being plugged in, the pump may have air bubbles in it, which can prevent water from circulating properly and can cause excess pump noise.
- Ensure that the pump is not suspended above the water. The pump must be fully submerged under the water.
- Check the flow control on the body of the pump, it may need to be adjusted to achieve the desired water flow rate.
- Inspect the pump and tubing for obstructions.
- Pump noise can be caused by trapped air, low water level, or the pump being too close to the sides of the fountain. Check the pump. If necessary, adding water or moving the pump helps to reduce noise.
- Check to make sure the power outlet is working; consult a certified electrician if in doubt about electrical connections.
- If you experience issues with assembly or the product was damaged during shipping, please contact our customer service team through one of the methods mentioned.
- Please have the item number and order information ready to expedite response time.
IMPORTANT SAFETY INFORMATION
- For outdoor use only.
- Keep the fountain out of reach of children and pets.
- Make sure the power cord is away from traffic areas.
- Keep the power cord away from all heat sources. Do not use electrical cords in areas with high temperatures.
- Check the water level frequently to ensure the pump remains fully submerged; never allow the pump to run dry as it will burn out the motor.
- Always unplug the power supply before cleaning and maintaining the fountain and the recirculating pump.
- Take care when handling the pump; only pick it up by the body of the pump, never by the power cord.
Any modification to the product or failure to follow recommended care will void the product warranty.
WARNING!
Manufacturer and seller expressly disclaim any liability from personal injury,
property damage, or loss, whether direct or indirect, or incidental, resulting
from the incorrect attachment, improper use, inadequate maintenance, or
neglect of this product.