AURORA ST324RGB DC RGB Flexible High Density LED Strip Light User Guide

ST324RGB DC RGB Flexible High-Density LED Strip Light
User Guide

ST324RGB DC RGB Flexible High Density LED Strip Light

Document Version -ST324RGB_V1_19 (AURORA)

IMPORTANT INSTALLATION INFORMATION

• Installation should be carried out by a qualified electrician in accordance with the latest edition of the National wiring regulations.
• The LED Strip operates at 24V DC.
• A 24V DC LED Driver is required (not included). A 24V RGB Controller is required (not included).
• When connecting to an LED 24 V Driver and 24V RGB Controller, ensure that the polarity is correct. The strip may be damaged if connected incorrectly.
• Please note that the strip is IP67 but any user-made connections or joints cannot be guaranteed to be IP-rated.
• Before commencing installation or maintenance, ensure electricity is switched off at the mains.
• Ensure that ALL electrical connections are tight with no loose strands, including factory connections.
• A soldering iron and heat gun are required for installation (not supplied).

24V DC LED FLEXIBLE STRIP LIGHT AND ACCESSORIES
ST324RGB High-Density RGB Flexible LED strip light
STRUCK Connector kit accessory

• To install the LED Driver and LED Controller please refer to their own instructions.
• A maximum of 5m of can be connected in a continuous length. For runs of over 5m connect individual lengths in parallel.
• The EN-STRGBCK is used to connect the strip to a 24 V DC RGB Controller
• At the strip connection carefully cut away the plastic sheath to reveal the +ve and RGB connection points.
• The copper track is lacquered which will need to be removed so that the solder will take to the copper track. Use a knife to carefully scrape away the lacquer from the surface of the copper track.
• ‘Tin’ the copper track and the EN-STRGBCK connection wires.
• Carefully solder the wires onto the LED strip. Match the colors of the wires, i.e. red, green, and blue to the RGB LED strip markings. The black wire is soldered to the common on the LED strip.
• Apply the glue to the connection and end of the strip. Next, slide the heat shrink sleeves in place over the connection and end of the strip.
• Gently apply heat to the sleeves with a heat gun until it shrinks over the connection and end of the strip. As this is a user-made connection an IP rating cannot be guaranteed.
• Ensure when applying the strip to the surface, it is smooth and clean.
• Connect the wires from the Controller to the LED Driver; ensure that the polarity is correct.

Environmental Protection (W.E.E.E.) – Aurora’s WEEE Reg.No. WEE/BG0130YX (UK Only)
Waste Electrical & Electronic Equipment Regulations (WEEE) require that any of our products showing this marking (left) must not be disposed of with other household or commercial waste. Aurora does not levy any WEEE disposal charges to its customers for affected WEEE-related products. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate any such product from other waste types and recycle it responsibly at your local facilities. Check with your Local Authority, Recycling Centre or retailer for recycling advice. If, when you purchased any Aurora product, your supplier included a WEEE disposal fee, you should then contact your supplier for advice on his take-back of the product for the correct disposal.

GUARANTEE

This product is guaranteed for a period of 3 years from the date of purchase. The guarantee is invalid in the case of improper use, installation, tampering, and removal of the Q.C. date label, installation in an improper working environment or installation not according to the current edition of the National Wiring Regulations. Should this product fail during the guarantee period it will be replaced free of charge, subject to correct installation and return of the faulty unit. Aurora does not accept responsibility for any installation costs associated with the replacement of this product. This warranty is in addition to the statutory rights in your country of purchase. Aurora reserves the right to alter specifications without prior notice.

Online
Tel: 01727 836611
Fax: 01727 836622
Website: www.enlitelighting.com
Email: sales@enlitelighting.com
Aurora Limited 6 Little Burrow,
Burrowfields,
Welwyn Garden City,
AL7 4SW, United Kingdom

References

• Oslo Sportslager - kvalitet - service - kunnskap i 90 år

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>