SONOFF M5-1C-80W Smart Wall Switch User Manual

SONOFF M5-1C-80W Smart Wall Switch

Specifications

• Model: M5-1C-80W, M5-2C-80W, M5-3C-80W
• MCU: ESP32
• Rating: 1C: 100-240V ~ 50/60Hz 10A Max, 2C: 100-240V ~ 50/60Hz 5A/Gang 10A Total Max, 3C: 100-240V ~ 50/60Hz 2A/Gang 6A Total Max
• Max. Load: 1C: 2200W, 2C: 2200W(1-1100W/Gang), 3C: 1320W(1-440W/Gang)
• LED Load: 1C: 300W/220V, 150W/110V, 2C: 300W/220V/Gang, 150W/110V/Gang, 3C: 100W/220V/Gang, 60W/110V/Gang
• Wireless Connectivity: IEEE 802.11 b/g/n 2.4GHz
• Net Weight: 1C(131.5g), 2C(139g), 3C(141.3g)
• Dimension: 86x71x41.5mm
• Color: White
• Casing Material: PC V0+CRS
• Applicable Place: Indoor
• Working Temperature: -10°C to 40°C
• Working Humidity: 5% to 95% RH, non-condensing
• Certified Compliance: CE/RoHS
• Executive Standard: EN 60669-2-1

Installation

1. Power off: Install and maintain the device by a professional electrician. Do not operate any connection while powered on.

2. Wiring instruction: Ensure a Miniature Circuit
   Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating is installed. Connect wires correctly.

3. Power on: After powering on, the device will enter the Pairing Mode. The LED indicator will flash in a specific pattern.

Add Device

1. Matter Pairing: Use a Matter-compatible App to scan the Matter QR code to add the device.
   • Add to Alexa via Matter
   • Add to Google via Matter
   • Add to Apple via Matter
2. eWeLink App Pairing:
3. Download the eWeLink App from Google Play Store or Apple App Store.
4. Add device by scanning the QR code on the device.
5. Follow wiring instructions and consult an electrician if needed. Power on the device and long press the button for 5 seconds.

Frequently Asked Questions (FAQ)
Q: How do I know if the device is online?
A: The Wi-Fi LED indicator will keep on if the device is online in eWeLink Mode or Matter Mode.

User Manual

SwitchMan Smart Wall Switch

Introduction

This device is a smart physical wall switch. After pairing it with eWeLink App, you can turn on/off the connected devices via the smartphone wherever you are, schedule its on/off, share it withyour families to control together, etc.

1. Button
   • Press once: Turn on/off the Device.
   • Press and hold for 5 seconds: Device enters the pairing mode.
2. Wi-Fi LED indicator (Blue) eWeLink Mode
   • Keeps on: Device is online.
   • Flashes twice: LAN
   • Flashes once: Offline
   • Flashes two short and one long: Device is in pairing mode.

Matter Mode

• Keeps on: Device is online.
• Flashes once: Offline
• Flashes two short and one long: Device
• is in pairing mode.
• Flashes three times: Identify

Matter-compatible ecosystem

Specification

• 1C: 100-240V ~ 50/60Hz 10A Max
• 2C: 100-240V ~ 50/60Hz 5A/Gang 10A Total Max
• 3C: 100-240V ~ 50/60Hz 2A/Gang 6A Total Max

Max. Load|

• 1C: 2200W
• 2C: 2200W(1-1100W/Gang)
• 3C: 1320W(1-440W/Gang)

LED Load|

• 1C: 300W/220V, 150W/110V
• 2C: 300W/220V/Gang, 150W/110V/Gang
• 3C: 100W/220V/Gang, 60W/110V/Gang

Wireless Connectivity| IEEE 802.11 b/g/n 2.4GHz
Net Weight| 1C(131.5g), 2C(139g), 3C(141.3g)
Dimension| 86x71x41.5mm
Color| White
Casing Material| PC V0+CRS
Applicable Place| Indoor
Working Temperature| -10℃~40℃
Working Humidity| 5%~95% RH, non-condensing
Certified Compliance| CE/RoHS
Executive standard| EN 60669-2-1

Installation

1. Power off
   *Please install and maintain the device by a professional electrician. To avoid electric shockhazards, do not operate any connection or contact the terminal connector while the device is powered on!
2. Wiring instruction
   
   To ensure the safety of your electrical installation, it’s essential either a Miniature Circuit Breaker (MCB) or a Residual Current Operated Circuit Breaker (RCBO) with an electrical rating of 10A (1C, 2C), 6A(3C)has been installed before the M5-80W.
   Make sure all wires are connected correctly.
3. Power on
   After powering on, the device will enter the Pairing Mode defaulted during the first use, and the LED indicator flashes in a cycle of two short and one long.

*The device will exit the Pairing Mode if it is not paired within 10mins. If you want to enter this mode again, please long press the button for 5s until the LED indicator flashes in a cycle of two short and one long and then release.

Add device

1. Method 1: Matter Pairing
   Open a Matter-compatible App (e.g. Alexa App, Google Home App, or Apple Home App, etc.) to scan the Matter QR code on the Quick Guide or the device itself to add the device.
   

2. Method 2: eWeLink App Pairing

Download the“eWeLink”App
Please download the “eWeLink” App from Google Play Store or Apple App Store.

Add device

1. 

2. 3. Please follow the wiring instructions to connect the wires (ensure power isdisconnected in advance and consult an electrician if needed)

3. Power on the device
   

4. Long press the button for 5 seconds

5. Check Wi-Fi LED indicator flashing status (Two short and one long）
   

6. Select“Add Device”

7. Search for the device and start connecting
   

8. Select the “Wi-Fi” network and enter the password.

9. Device“Added completely”.
   

Device Network Changing
Change the device’s network by “Wi-Fi Settings” in the “Device Settings” page on the eWeLink App.

Device Factory Reset (Dual Ecosystem)

• After “Delete the Device” in the eWeLink App
• For devices previously successfully added to eWeLink, perform a new pairing using a different eWeLink account
• For devices previously successfully added in Matter, perform a new Bluetooth Pairing through Matter

FAQ

Fail to pair Wi-Fi devices with eWeLink APP

1. Make sure the device is in pairing mode.
   The device will automatically exit the pairing mode if not paired within 10mins.

2. Please turn on the location service on your mobile phone and give the permission. Before choosing the Wi-Fi network, the location service should be turned on and the permission is given. Location information permission is used to obtain Wi-Fi list information. If you tap “Disable”, the device will not be added.

3. Make sure your Wi-Fi network runs on the 2.4GHz band.

4. Make sure you entered a correct Wi-Fi SSID and password, no special characters contained. A wrong password is a very common reason for pairing failure.
   You may get the device close to the router for a good signal transmission while pairing.

5. Please try to pair the device in the compatible mode.

6. Wi-Fi devices “Offline” issues Please check the following issues by the Wi-Fi LED indicator status:

The LED indicator blinks once every 2s means you fail to connect to the router.

1. Maybe you entered a wrong Wi-Fi SSID and password.
   Make sure your Wi-Fi SSID and password don’t contain special characters, for example, the
   Hebrew, Arabic characters. Our system can’t recognize these characters so that fail to connect to the Wi-Fi.

2. Maybe your router has a lower carrying capacity.

3. Maybe the Wi-Fi signal strength is weak. Your router is too far away from your device, or there may be some obstacles between the router and the device so that the signal transmission is blocked.

4. Be sure that the MAC of the device is not on the blacklist of your MAC management.

The LED indicator flashes twice on repeated means you fail to connect to the server.

1. Make sure the Internet connection is normal. You can use your phone or PC to connect to the Internet, and if you fail to access, please check the availability of the Internet connection.
2. Maybe your router has a low carrying capacity. The number of devices connected to the router exceeds its maximum value. Please check the maximum number of devices that your router can carry. If the number of connected devices exceeds the maximum value, please delete some devices or change a larger router and try again.
3. Please contact your ISP and confirm our server address is not shielded: cn-disp.coolkit.cc (China Mainland) as-disp.coolkit.cc (in Asia except China) eu-disp.coolkit.cc (in EU)

us-disp.coolkit.cc (in US)
If none of the above methods solved this problem, please submit your issue via help&feedback on the eWeLink App.

SAR Warning

Under normal use of condition, this equipment should be kept a separation distance of at least 20 cm between the antenna and the body of the user.

WEEE Warning
WEEE Disposal and Recycling Information All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Shenzhen Sonoff Technologies Co., Ltd declares that the radio equipment type [M5-1C- 80W，M5-2C-80W，M5-3C-80W ] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address

https://sonoff.tech/compliance/

RACCOLTA DIFFERENZIATA
Separa le componenti e conferiscile in modo corretto.

• Manufacturer: Shenzhen Sonoff Technologies Co., Ltd.
• Address: 3F & 6F, Bldg A, No. 663, Bulong Rd, Shenzhen, Guangdong, China ZIP code: 518000 Service email: support@itead.cc
• Website: sonoff.tech Made in China

References

• Welcome to OpenResty!
• Welcome to OpenResty!
• Welcome to OpenResty!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>