CASAMBI HDN20CB-B Programmable Constant Current LED Driver Owner’s Manual

June 12, 2024
CASAMBI

HDN20CB(-B/-E)
Owner’s Manual

CASAMBI HDN20CB-B Programmable Constant Current LED
Driver

Feature

  • Output current set from App
  • 100% non-flicker DC dimming
  • Current trim fine tuning
  • Fading time adjustable
  • Dimming curve adjustable
  • Single color / CCT in one model
  • Very low standby power
  • Premium low brightness performance

Introduction

This product is a 20W programmable constant current LED driver. Model HDN20CB-E is for single color and HDN20CB-B can be used for CCT or single color. It is Casaba ready and all features are programmable.
The output channel, rated current, fading time and trim level features are all adjustable from the Casaba app. These features allow customer to apply in various application with multiple options.
The advanced full DC dimming scheme is implemented, and it’s 100% physically flicker free in whole dimming range. It also has very good low brightness performance, to build elegant low brightness environment and on/off dimming experience.

Setting output current and channel

The rated output current of HDN20CB is from 200mA to 1050mA, it needs to be set from the Casaba app. To set the current and output mode, please make sure the driver is unpaired and powered on. On the Casaba app, click on the driver icon and select ‘Change profile’ option on the pop up manual (Fig.1). The rated current and working mode can be selected in the list (Fig.2).
The HDN20CB-B model can be configured as CCT or single color model, once be configured as single color model, user can connect lighting fixture to both warm white and cool white channel.

CASAMBI HDN20CB-B Programmable Constant Current LED Driver -
Fig1The max output voltage varies with the rated output current. The following table lists the max output voltage and power with different current setting.

Rated current 200mA 250mA 300mA 350mA 400mA 500mA 600mA
Max output Volt. 50V 50V 50V 50V 50V 40V 33.3V
Max output power 1 OW 12.5W 15W 17.5W 20W 20W 20W
Rated current 700mA 800mA 900mA 1050mA
--- --- --- --- ---
Max output Volt. 28.6V 25V 22.2V 19V
Max output power 20W 20W 20W 20W

Automatic LED adaption

This driver verifies the load character on each power on. It will run a load adaption process once the change of load is detected. During the adaption process, the lighting fixture will dim up and down for about 10 seconds. After this process, the driver will match the LED feature and maintain a 0-100% full range physical non-flickering DC dimming. Normally this adaption process happens on the power on moment once the lighting fixture is changed with the brightness is higher than 30%.
For HDN20CB-B, each LED channel must has same voltage and current feature for proper adaption and working. If two channel’s voltage and current does not match, the CCT adaption will fail and the driver will only work in single color mode with limited function.
CAUTION: The adaption process CAN NOT detect the value of LED rated current, so the driver rated current MUST be set correctly before connecting the driver to the lighting fixture. Otherwise the lighting fixture may be permanently damaged.

Advanced feature – Current trimming

To fine tune the LED driving current, please pair the driver first and double click on the driver icon to open the setting page. On the setting page please click on the ‘Current trim’ item in the PARAMETERS section (Fig.3). The output current can be trimmed from 100% to 50% of the rated current at 5% step (Fig.4).

CASAMBI HDN20CB-B Programmable Constant Current LED Driver -
Fig2

Advanced feature – Change dimming curve

The dimming curve defines the trend of light output strength versus brightness level (0-100%) showing on the app. Please pair the driver first and open the setting page on the app, from the PARAMETERS section, the Dimming curve can be changed from Logarithm, Linear and Optimized logarithm (Fig.5).
The Linear curve will result even light output power versus the brightness level set on app, but for human eye sensing, the light output change is relative too small at high brightness level.
The Logarithm curve will result strong brightness change at high brightness level and this will make the brightness adjustment is more visible and logical for human eye.
The Optimized logarithm curve is between linear and logarithm, results an balanced brightness adjustment effect.

Advanced feature – ON/OFF fade time adjust

The on/off fade time can be adjusted on the setting page. Please pair the driver first and open the setting page on the app, from the PARAMETERS section, the ON/OFF fade time can be adjusted from 0-25.5 seconds. User can adjust it by entering value between 0-255 with the step of 0.1 seconds (Fig.6).

Specification

Model HDN20CB-B HDN20CB-E
Function 2-in-1 (CCT/Single Color) Single Color
Rated max power 20W
Input power AC 180-240V
Power Factor >0.9 at rated load
Efficiency >85% at full load
Output voltage 0-50V DC
Rated output current (mA 200, 250, 300, 350, 400, 500, 600, 700, 800, 900,

1050
Fade time| 0-25.5 seconds adjustable
Output current trim| 100% to 50% with 5% step
Dimming method| Full DC dimming
Standby power consumption| <0.5W
Working temperature| -20~50°C
Case temperature| Max 90°C
Dimension (WHL)| 31.5 x 24 x 125.5mm

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals