LANCOM UF-360 Unified Firewall User Guide
- June 4, 2024
- LANCOM
Table of Contents
LANCOM UF-360 Unified Firewall User Guide
MOUNTING AND CONNECTING THE DEVICE
-
Serial configuration interface RJ45 (CONSOLE)
Maintenance interface for expert configuration. Not necessary for initial commissioning.
-
USB 3.0 interfaces
Interfaces for reinstallation of the device software.
Not necessary for initial commissioning. -
RESET button
Press the reset button to restart the device.
RESET -
TP Ethernet interfaces ETH0 – ETH5
Connect the ETH0 – ETH5 TP Ethernet interfaces to additional network components using suitable Ethernet cables. -
SFP+ interfaces ETH6 – ETH7
Connect the ETH6 – ETH7 SFP+ interfaces to other network components using suitable SFP(+) modules. -
Slot for extension modules
Slot for RJ45, SFP or SFP+ extension modules -
Connection socket for power supply (device rear side)
Supply the device with power via the mains connection on the rear of the device. Use only the supplied power cord for this purpose. -
Power switch (rear side)
Power on the device after having connected the power cable.
Please observe the following when setting up the device
- The mains plug of the device must be freely accessible.
- Do not rest any objects on top of the device and do not stack multiple devices.
- Keep the device’s ventilation slots clear of obstruction.
- Mount the device into a 19” unit in a server rack using the separately available rack mount.
Before initial startup, please make sure to take notice of the information
regarding the intended use underwww.lancom-systems.com/safety!
Operate the device only with a professionally installed power supply at a
nearby power socket that is freely accessible at all times.
TECHNICAL DATA
1 LEDs HDD / Power
HDD off| No HDD read / write access
HDD green| HDD read / write access
POWER off| Device switched off
POWER green| Device ready and accessible
2 LEDs ETH6 – ETH7 – SFP
LEDs left – Link activity
Off| no link detected
Green, permanently| Link detected, no port activity
Green, blinking| Link detected, port activity
LEDs right – Link speed
Off| No link detected
Green, permanently| Link detected
3 LEDs ETH0 – ETH5 – TP Ethernet
LEDs left – Link activity
Off| no link detected
Green, permanently| Link detected, no port activity
Green, blinking| Link detected, port activity
LEDs right – Link speed
Off| Link speed 10 Mbps
Green, permanently| LinkSpeed 1000 Mbps
Orange, permanently| Link speed 100 Mbps
Hardware
Power supply| Internal power supply unit (100–240 V, 50–60 Hz)
Power consumption| Max. 60 W
Environment| Temperature range 0–40 °C; humidity 10–85 %, non-condensing
Housing| Robust metal housing 1 HU, with mounting brackets for 19“ mounting;
Network connections on the front side
Fans| 2
Dimensions (mm)| 440 x 44 x 269.2 (W x H x D)
Interfaces
ETH| 6x 10 / 100 / 1000 Mbps Gigabit Ethernet ports
SFP+| 2x SFP+ ports
USB| 2x USB 3.0 ports
Console| 1x RJ45 configuration interface
**Declaration of Conformity
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen,
declares that this device is in compliance with Directives 2014/30/EU,
2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of
the EU Declaration of Conformity is available at the following Internet
address: www.lancom-systems.com/doc
****Package contents**
Documentation| Quick Reference Guide (DE/EN), Quick Install Guide (DE/EN),
Service & Support Guide (DE/EN)
Accessories| 1x IEC power cable 230 V; 2x 19“ mounting brackets; 1 set
adhesive rubber pads
ANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>