Casta Diva CD-K010 Smart Toilet with Built in Bidet Installation Guide
- May 15, 2024
- Casta Diva
Table of Contents
Casta Diva CD-K010 Smart Toilet with Built in Bidet
Product Specifications
- Model: CD-K010
- Technical Support: Lifetime free technical support
- Email: service@castadivahome.com
- Phone: 1-209 389 9799
DANGER-Reduce the risk of electric shock
- Do not use it while bathing.
- Do not place or store the product where it may fall or be dragged into a bathtub or sink.
- Do not place in or drop into water or other liquid.
- Do not touch the product if it falls into the water, and unplug the power supply immediately.
WARNING -Reduce the risk of burns, electric shock, fire, or personal injury
- Please keep a close watch when children or disabled persons are using or near the products in use.
- This product is used only for the intended purpose described in this manual. Do not use accessories not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
- Keep the power cord away from the heating surface.
- Do not clog the vents of the product, or place the product on a soft surface, such as a bed or sofa, where the vents may be blocked. Keep the air unblocked and no cotton wool hair, etc. in the pores.
- Don’t use products while sleeping or drowsy.
- Do not put or insert any object into any opening or hose.
- Do not use outdoors or operate where aerosol (spray) products are being used or when oxidated products are being administered.
- Unplug this product before filling it. Fill (reservoir) with water. Do not overfill (or specify fillinginstructions).
- Do not clean the product and power plug with water, it might cause electric shock or damage.
- Do not disassemble, repair, or modify the product, otherwise, it might cause a fire.
- Do not stand or put heavy things on the seat, it might cause product damage.
- Do not throw burning items like cigarette butts into the product, it might cause a fire.
- Do not open or close the cover or seat forcibly, and do not lean on the cover when the product in use, it might cause product damage.
- Connect this product to a properly grounded outlet only. See Grounding Instructions.
- This product must be plugged into a regular voltage Grounded GFCI outlet (North America 120V AC, 60Hz). The rated power consumption is 1000W.
- Do not use an extension cord. If you are not sure if the equipment is properly grounded, consult a licensed electrician.
FCC STATMENTS
ISED Warning statements in User Manual
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
FCC Warning Statements in User Manual
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment and may void the factory warranty.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, according to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used per the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Safety Information
Precautions before use
In order to avoid personal injury and property damage to users and other
people, please read the following safety precautions carefully and strictly
observe them. After reading, please keep this manual in a drawer where you can
access it easily.
PROHIBITED
- Do not touch the power plug with a wet hand, otherwise, it may cause an electric shock.
- It is strictly forbidden to put the electrified product on its side or upside-down, otherwise it may cause fire or burn down.
- It is strictly forbidden to disassemble, repair, or transform the product by yourself, otherwise it may cause fire or electric shock.
- It is strictly forbidden to put lighted cigarettes and other combustibles into the toilet cover, otherwise it may cause fire.
- It is strictly forbidden to use this product when the seat and upper cover are not fully opened or closed.
- It is strictly forbidden to use a power extension cord or loose and unstable power socket, otherwise, it may cause fire electric shock, or jam.
- It is strictly forbidden to put fingers or other objects into the warm air outlet, otherwise, it may cause scalding, electric shock, or burn.
- It is strictly forbidden to pour water, detergent, urine, or other liquid on the body or power plug, otherwise it may cause fire or electric shock.
NOTICE
- When thundering, please pull out the power plug.
- Do not operate products that have fallen into the water or soaked in water, and immediately unplug the power plug.
- The socket should be installed in a place where it is not easy to get wet. It is recommended to use a waterproof socket. It is recommended to place the plug on the wall. Please refer to the technical drawings and suggestions on a power line and water supply connection.
- Please do not connect the inlet water line with the outlet water line of the water heater. The inlet water temperature should be 37.4℉ – 95℉.
- Do not let the sunlight directly irradiate the product, to avoid the product discoloration or the burn due to the temperature instability.
- Do not use industrial water, wastewater, seawater, reclaimed water, and other water sources, otherwise, it may cause skin inflammation and other diseases.
- This product is for household use only.
- The product must be connected to a separate circuit. No other electrical product shares the circuit with this product. Sharing a circuit can cause a fuse to blow out or a circuit breaker to trip. Continuous use in such cases may result in fire or property damage.
- Do not use banana oil, gasoline, liquid medicine and detergent, insecticide, or hard brush to clean this product. Toilet cleaner may only be used for ceramic bodies.
- Do not use this product in rooms with humidity more than 90% RH, the use environment should have a dry and wet separation, such as installing a shower room or shower curtain.
- For the newly decorated house, the residual mud and sand in the pipeline are easy to damage the machine and affect human health. Please remove the sewage from the pipeline before installation.
- Do not apply strong strength or impact to the product, do not stand on the seat or toilet lid, do not place heavy objects, and do not press or lean on the toilet lid, so as not to damage the product.
- Please set the temperature of water and seat on low when the old, weak, sick disabled, or children use the product, and touch the sensor when you sit on the seat properly.
- Pull out the power plug before cleaning, do not wet the product directly.
- In cold winter, if do not use the product for a long time, please discharge the tank water following the instructions. Or it might cause product damage.
- This appliance is provided with a protective device that may make the appliance inoperable under some abnormal conditions(such as immersion of the appliance). If the appliance becomes inoperable, contact the CASTA DIVA service team.
MUST ABIDE BY
- Do not let children play with this product.
- Do not supply water or power to the product before installation is completed.
- If it is not used for a long time, please unplug the plug and empty the water in the product.
- When installing, disassembling, repairing, and maintaining the product, the power plug must be pulled off and the water supply valve must be closed.
- This product uses an AC 120V/ 60Hz power supply; to ensure safe use, the socket and its connecting wires must be able to withstand more than 15A current.
- After the appliance is scrapped, please hand it over to a qualified professional recycling company or organization for disposal. It should not be discarded at will, to avoid harm to the environment.
- To prevent damage caused by freezing, please take measures to keep warm. If the room temperature is below 32℉, it is recommended to drain the water in the product to prevent internal frost cracking.
- The plug should be installed in place, and the plug pin cannot be exposed to air.
- Product installation and use should be away from heat and fire sources
Grounding instructions
This product should be grounded. In the case of an electrical short
circuit, grounding reduces the risk of electric shock by providing an escape
path for the current. This product is equipped with a power cord with a ground
wire and a properly grounded plug. The plug must be plugged into a properly
installed and grounded socket.
DANGER: Improper use of the grounding plug may result in electric shock the power cord or plug needs to be repaired or replaced, do not connect the ground wire to any of the flat pins. The conductor with a green stripe or without a yellow stripe on the outer insulation surface is the grounding wire.
- If you do not fully understand the grounding instructions or if you have questions about whether the product is properly grounded, please consult a qualified electrician or maintenance personnel.
- This product is for use on a normal 120 V circuit and has a grounding plug that looks like the plug illustrated in sketch A .in Figure 1. A temporary adapter, which looks like the adapter illustrated in sketches B and C, may be used to connect this plug to a 2- pole receptacle as shown in sketch B. if a properly grounded outlet is not available. The temporary adapter should be plugged into a properly grounded outlet (sketch A) and should be installed by a licensed electrician. The green colored rigid tab extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must be held in place by the screw.
- The product is factory-equipped with a specific power cord and plug that allows connection to the appropriate circuit. Make sure the product is connected to the same socket as the plug configuration. This product should not use adapters. Do not modify the supplied plug, if it is not suitable for the socket, please install the appropriate socket by a qualified electrician. If the product must be reconnected using different types of circuits, it should be reconnected by qualified maintenance personnel.
- If an extension cord is required, only use a 3-core extension cord with a 3-core grounding plug and a 3-slot socket that accepts the plug on the product. The damaged wires must be replaced or repaired.
Preferred Connection
Temporary Connection
SAVE THESE INSTRUCTIONS
Pre-installation
Tools required
Hardware Included
Technical specifications
Note: Rated power is the average power under the conditions of the ambient temperature of 73.4℉±3.6℉, inlet static pressure of 30psi ± 3psi, the inlet water temperature of 41℉±0.9℉, turn on the rear wash function and set the water flow, seat temperature and water temperature to the highest level successively, and press Stop button then starts rear wash function immediately and continue to work steadily for one cleaning cycle.
Installation
Suggestions on power line and water supply connection Technical drawings and power cord connection suggestions
NOTE: It is necessary to install the provided angle stop in an accessible
area for quick shutoff in case of an emergency.
The power socket can be installed on either left or right.
This product is suitable for AC120V/60HZ power supply. In order to ensure safe use, the socket, and its connecting wires must be able to withstand more than 15A current.
-
Install the Adapter Nut and angle Stop Wrap Teflon tape on both outlets of the water supply and angle valve. Insert sealing gaskets in both sides of the adapter nut, then tighten direction N to the water supply outlet, and direction G to the angle valve outlet. Replace the existing angle valve with our angle valve to ensure the best performance of the toilet. To ensure proper installation, call a professional plumber to do the replacement.
-
Install Toilet and Toilet Wax Ring( For Option B installation, please see template.)
-
Install the Water Supply Hose
As shown in the figure, install the water supply line to an angle stop.- If the water inlet pressure is greater than 30psi, please install the flow limiting plate in the angle stop;
- Only use the accessory parts that are shipped with the product for installation;
- After installation, check the water seal and turn on the power supply. Water leakage shall be avoided.
-
Tips for comfortable use
Spots are easily found at the lower part of the product after a long time of water or urine penetration. To avoid this, silicone is recommended to paste around the lower part to seal the tiny gap between the lower part and the ground. -
Install the Remote Control Installation Method 1: Installation Method 2:
Connecting Remote Control
Long press the remote control stop button, and the first, third, and fifth
LED lights start flickering indicating the remote control connection is ready.
Then release the remote control stop button and power on the smart toilet. If
the connection succeeds, the five LED lights on the remote control will be on
for 3 seconds and then go off; if it fails, the first, third, and fifth LED
lights will flash for 30 seconds and then automatically go off. If you want to
quit the process of connecting, please exit by pressing the stop button.
Leakage protection test
Test frequency of 1-4 points below (once a month)
- Under normal conditions, press the “reset” button on the power plug, the plug indicator light will be on and the product will start to power on.
- Normal working condition: under rated voltage conditions, the product will enter a normal working state after completing the self-inspection of water and electricity.
- Press the “Test” button, when the leakage protection is normal, the indicator light is turned off and the power is turned off.
- Press the “Reset” button on the power plug again. The indicator light will be on and the power supply is restored.
WARNING
- Check if any leakage occurs when the power switch does not work properly.
- The leakage protection plug only protects the product connected to the power supply through the plug.
- When using other electrical appliances, the product does not guarantee leakage protection of other products; similarly, the product does not replace the basic safety measures of other electrical appliances. 3. Do not ground the live wire directly, test the leakage protection function of the product plug.
Functional Test
- Press the “Seat Sensor” position with your hand, at the same time press the Rear/ Front cleansing button. Check whether the nozzle works well.
- Place a cup or bowl in front of the spray nozzle to avoid getting wet.
Tip: After switching on the power, the product will do self-inspection.
Operation
Side button description
All cycle times may vary
Indicator light icons
Remote control instructions
Rear cleansing/Front cleansing
When sitting, press button or button, enter the rear cleansing or front cleansing mode, and press the button again to enter the oscillated cleansing mode. The cleansing cycle stops automatically after 3 minutes; or press button to stop the cleansing function.
ECO function
Long press Button, and turn on/off the ECO function, when the ECO function
is on, the seat temp. will decrease slowly after leaving the seat then keep at
82.4℉±5.4℉.
Warm air dryer
When sitting on seat, press To activate the drying function. It will stop
when (1) you press Button (2) working ≥ 5min (3)stops at any time when the
user leaves the seat.
User profile
After User 1 sets the desired functions (Water temperature, drying
temperature, water pressure, position), press button of the remote control for
3 seconds until the 5 indicator lights of the remote control flash 3 times.
The desired functions will be saved as user1. The saved setting will be
invoked when the user presses a button on the remote control. The 5 indicator
lights of the remote control flash 1 times.
After User 2 sets the desired functions (Water temperature, drying temperature, water pressure, position), press button on the remote control for 3 seconds until the 5 indicator lights of the remote control flash 3 times. The desired functions will be saved as user2. The saved setting will be invoked when the user press button on the remote control. The 5 indicator lights of remote control flash 1
Foot sensor mode
In off-seat status, foot detection mode will achieve the following
function:
- When the lid & seat are closed, footstep in the detection area to trigger lid opening.
- When the lid is opened, the seat is closed, footstep in the detection area triggers the seat opening.
- When the lid and seat are opened, footstep in the detection area to trigger the lid and seat closing and flushing.
Using Instruction:
- The foot sensor flush works only in off-seat status.
- Enter the sensing area (from the ceramic bottom to the indicator’s illumination range) and stay about 0.5s to activate the flush funtion.
Warm tips:
The sensor is an optical device, which is highly sensitive and may have the
following issues.
- Stains, water drops, or fog on the sensor surface might cause sensing failure. Please wipe up in time.
- Direct sunshine and bathroom heater lamps might cause sensing failure.
- Mopping and other moving objects in front of the sensor might cause sensing failure.
- If the shower keeps spraying the sensor might have the probability of a wrong trigger.
- The foot sense breathing light flashes, which is convenient for the user to identify the foot sense position, and is not an abnormal fault.
Flush function setting
Short press the button to turn on the flush function. Long press button to
turn on or off the automatic flushing function. After sitting for more than 3
seconds the toilet will detect the user. Then the toilet will auto flush
approximately 6 seconds after leaving the seat.
Lid/seat opening and closing
Press Button to open or close the lid; press Button to open or close the seat.
Automatic lid opening and closing
Long press button to turn on or off the automatic lid opening and closing function. When the Automatic lid opening and closing function is on, if the lid is closed, the lid will automatically open when detects the human body. After the lid is opened, if nobody sits on it and no human body is detected, the lid will close automatically after about 60 seconds.
Nozzle position adjustment
In the state of cleansing, press button to forward the nozzle. Press button
to backward the nozzle, 5 levels adjustable.
Water pressure setting
While in the cleaning mode, Press+or- button to adjust the water pressure
at 5 different levels. Press + button once to raise one level press – button
once to decrease one level. The indicator light will display accordingly.
Water temperature setting
Press to adjust the water temperature at 5 different levels. Press once to
raise one level. Once the highest level is reached each press will decrease by
one level. The indicator light will display accordingly.
Nozzle automatic cleaning mode
In off-seat state, long press button, the nozzle extends out for automatic
cleaning for about 2 minutes and then retracts.
Press button, stop the nozzle self-cleaning.
Seat temperature setting
Press button to adjust seat temperature in 5 different levels. Press once
to raise one level. Once the highest level is reached, press again to lower
one level. The indicator light will display accordingly.
Drying temperature setting
Press button to adjust the drying temperature at 3 different levels. Press
once to raise one level . Once the highest level is reached, press again to
lower one level. The indicator light will display accordingly.
Night light setting
Long press button, the night light will switch between on and off mode.
Note
- When the automatic open and close function of the product is turned on, the product can identify the person moving within a certain distance from the ceramic front. This process is called microwave motion induction; When the product recognizes that the person is moving within the microwave induction distance, the lid will not automatically turn off. When the product recognizes that the person does not move within the microwave induction distance, the lid will automatically turn off after about 60 seconds.
- When there is a moving object around the toilet (such as a door opening or a curtain moving with the wind in the bathroom), it may lead to the automatic start-up of the self-opening/ closing cover function. When children use this product, the microwave inductor may not be able to sense.
- Note that when the body is close to the toilet (within the accessible range of the cover closing), if the body keeps still and the toilet is unseated, the lid will automatically close after about 60 seconds. which might lead to a lid touching the human body.
Indicator light (The sequence of the indicator lights in the figure below corresponds to that on the remote control)
Warning: If the drainage hose is blocked, stop water drainage. Find professional personnel to unclog the hoses, otherwise water may flow out of the ceramic.
Care and Cleaning
Cleansing filter screen
Nozzle cleansing
Long-time non-use processing mode
Step 1: When not in use, turn off the water supply, long press the button to enter self-cleansing mode. Move to step 2 after self-cleansing is completed.
Step 2: Pull the plug out, loosen the braided hoses, and drain out the inside water.
Cleaning the Cover & Seat:
- Turn off the water supply, and pull out the power plug.
- Use a soft and wet cloth to clean the product (Wring out a cloth)
Notices:
Do not use dry cloth or toilet paper to clean the product or the appearance of
the product will be scratched. Avoid putting water into the inside of the back
cover, otherwise, some electronic components in the back cover might be
damaged.
Troubleshooting
Frequently asked questions. (FAQ)
Please read the following questions carefully, and refer to the instructions.
If the product still does not work contact your local sales dealer or contact
the manufacturer.
Tips:
If there is water leakage, immediately turn off the water supply and pull the
power plug.
The following reasons may cause the product’s malfunction.
- Check the power supply
- Is the power supply working properly?
- Is the Plug plugged in?
- Is the electricity leakage protection switched off?
- Check the water supply
- Is the water supply working properly?
- Is the Water Supply off?
- Is the PSI lower than 30?
Once any of the following issues occur, please cut the power off immediately. Refer to the affected section in this manual. Please contact the manufacturer for more assistance if necessary.
- The indicator light icon flashes.
- The power leakage protection switch on the power plug trips frequently.
FAQ
(Frequently Asked Questions)
- Q: Can I use this product in water?
- A: No, do not use this product in water or wet conditions to avoid electric shock hazards.
- Q: What should I do if the product falls into the water?
- A: Unplug the power supply immediately and do not touch the product. Seek assistance from a professional.
- Q: Can I disassemble or repair the product myself?
- A: No, it is strictly forbidden to disassemble, repair, or modify the product by yourself to prevent fire or electric shock risks.
Get free technical support for the lifetime of your product.
- Email: service@castadivahome.com
- Phone: 1-209 389 9799
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>