Casta Diva CD-Y010S Smart Toilet with Built Bidet Instruction Manual

INTELLIGENT TOILET
Product Manual

CD-Y010S Smart Toilet with Built Bidet

Product Name: Intelligent Toilet
Model: CD-Y010S

Thank you for purchasing our product. Please read this manual before installation and use to ensure that your product will function at peak performance.
Read this manual thoroughly and store in a safe place for future references.
E-mail: SERVICE@CASTADIVAHOME.COM

IMPORTANT SAFEGUARDS
When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
DANGER- To reduce the risk of electrocution:

1. Do not use while bathing.
2. Do not place or store product where it can fall or be pulled into a tub or sink.
3. Do not place in or drop into water or other liquid.
4. Do not reach for a product that has fallen into water. Unplug immediately.

WARNING- To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or in valids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
9. Connect this product to a properly grounded outlet only. See Grounding Instructions.
10. Do not use while bathing.
11. Risk of Electric Shock. Connect Only to a Grounding Type Receptacle Protected by a Ground-Fault Circuit-Interrupter (GFCI)
12. Risk of electric shock. Connect only to a ground fault circuit protected (GFCI) type receptacle
13. CAUTION – Risk of electric shock, do not remove cover (or back). Refer servicing to quali- fled service personnel.
14. Caution – risk of electric shock, do not remove cover (or back). Refer the service to qualified service personnel.

SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded
DANGER- Improper use of the grounding plug can result in a risk of electric shock. If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded.

Notice: ● represents that the product have this function.
User Friendly Design
Kick control, Radar sensor,
New features to offer you an enjoyable experienceRotated Switch (Refer to page 13)
Inteling Toilet

Before Use

Parts Information
Overview, Remote controller
∎ Overview

Remote Control

TIPS:

1. Long press ‘H/C Massage’ to turn on/off all Function Prompt Tones (except Alert Tone)
2. Long press ‘Nozzle clean’ to turn on/off ECO mode. When seat heating is on, no operations ≥30mins, ECO mode is activated automatically. The seat temp will lower automatically and maintain the lowest temp setting.
3. When needs to turn on/ off the automatic open&close lid function, please press “Nozzle Clean+H/C Massage” button on the remote control.

Warnings And Safety
Please read thoroughly
First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference.
The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be held liable for any injuries to the user and damages to the product due to improper usage and/or failure to heed safety warnings.

Explanation of Terms and Symbols

Warning – [Indicates possible injury resulting from improper usage due to negligence of this sign.] Attention: – [Indicates human injury or property loss that may result in improper usage due to negligence of this sign.] ………….[Note] When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions.
………….[Prohibits any individual from performing any action with this symbol,] ………….[Prohibits any individual from dismantling product.] …………[Keep product away from any wet environments, including, but is not limited to, humid environments, close proximities to baths, showers or sinks.] …………[Do not touch!] …………[Do not touch with a wet hand!] …………[Keep away from any extreme heat or fire!] …………[Operate only as instructed!] …………[Pull out the power plug!] …………[Protective grounding]

Warning

**** This product needs to be properly grounded.
※ Risk of electric shock
※ If unsure, contact an electrician.
electrical installation company.
Do not touch, insert or pull out the power plug with a wet hand.
※ Risk of electric shock.
Do not use a power socket in poor condition or a damaged power plug.
※ Risk of fire and/or electric shock. The power socket in use should be within the specified range (AC120V ).
※Risk of fire and/or electric shock.

Do not pull, damage, bend, twist, stretch, roll, bundle, clamp or squeeze the power cable. Do not place anything on power cable.
※ Risk of fire and/or electric shock
lf the power cord is damaged, to prevent any injuries or accidents, it should be replaced by a professional.
※Risk of fire and/or electric shock
Do not place a lit cigarette along with other burning objects into the unit.
※ Risk of fire.
Do not use during thunderstorms (pull out the power plug during storms).
※ Failure in doing so may lead to injury or fault in the product When the seat ring or the cover plate is damaged, to avoid any harm, be sure to pull off the power plug, close the water source and contact your local distributor for replacement.
※ Risk of fire or electric shock.
Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth.
※ Risk of fire.
Any person with a disability, the elderly, and children, should be using this product with the supervision of another individual.
※ Be advised that sitting on the heated seat for an extended amount of time may result in burns.
This product is not a toy. Advise children not to play with product. (1)
※ Risk of injury.
Do not dismantle, repair or alter this product on your own. Callina professional for further advice.
※ Risk of fire, electric shock, and/or other accident that may lead to injury.

Warning
For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. (These include, but are not limited to products such as: concentrate sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetrachloride, chloroform, acetone, butanone, benzene, methylbenzene, phenol, methylphenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc).
※ Risk of damaging parts that can lead to accidents and injuries Do not add water or detergent into the unit or on to the wireless remote. Do not soak the product with water or cleaner.
※ Risk of fire and/or electric shock.
Do not install product in a humid eo environment or a soak room. Do not spray or soak this product with any form of liquid to prevent any damage to the product.
※ Risk of fire and/or electric shock. Do not use polluted water or water meant for industrial.
※ Risk of urocystitis or dermatitis.
Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.
Do not apply any force to the unit’s seat and lid. Do not stand on the lid or open or close the lid and the seat forcefully.
※ This may result in product damage and/or user injury. Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use.
※ Risk of fire, electric shock, and/or other accident that may lead to user injury. Do not spray urine at the dryer trap.
※ Risk of electric shock.
**** Read the following for proper battery usage.

• Properly install the battery according to its correct polarity.
• Remove the battery during long periods without use.
• Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals.
• Cover the battery with tape before disposal.

※ This will prevent battery fluid leaks that may cause fire and/or other damages.

Warning

• **** Place the battery out of children and infant reach.
  ※ If battery is swallowed, contact a doctor immediately. (1)

• If battery fluid leaks onto user, quickly rinse off area using water.

• If battery fluid gets into eyes, do not rub your eyes. Quickly rinse it with water and consult a doctor immediately.

※ May result in vision impairement or blindness.
**** When the battery is in use, do not do the following operations.

• Do not hold or store with metal objects (such as a necklace or a watch).
• Do not mix new and old batteries.
• Do not pull battery apart battery or throw it into water and/or fire. Battery fluids may cause a fire.

Attention

Do not use the heated seat or warm dryer temperature for an extended amount of time.
※Extended use may result in burns.
While using this product, make sure that the skin Is in contact with the seat sensor area. Otherwise, product may not operate correctly.
※ Children and smaller individuals may have trouble staying in contact with sensor area. Do not spray urine in the direction of the bidet nozzle.
※ Doing so may result in blockage to the bidet nozzles and cleaning area.
Do not use your old hose component.
Use the one provided with your product. Anything else connected to the older hose may need to be replaced.
※ Risk of water leakage and/or property loss/damage.
In case of sudden power failure, remove the power plug and close the angle valve to prevent water leakage.
※ Risk of water leakage and/or property loss/damage.
Avoid direct sunlight or heat.
※ Risk of product discoloration.
Do not supply electricity with an external switch. le: connecting the universal part to a timer switch.
※ Run the risk of issues caused by impror resetting the thermal breaker.
When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed, be sure to fasten it with force.
※ Risk of water leak
Pull out the power plug when the product is in disuse for an extended amount of time. Make sure to shut off the water and remove the water inside the product.
※ Risk of fire, leaks, and product damage.
**** When storing or transporting in cold climate, make sure to remove all water from the unit. Product may crack and other damages may occur due to freezing water.
※ Risk of fire, leaks, and product damage.

Functions

Installation
Tools required for installation
Required tools
Required tools for installation. Please have these tools prepared prior to installation. Item list (Confirm that all below items are inside the box)

※ Please confirm all the aforementioned items are inside the package.
lf there are any omissions, please contact our customer service.
※Illustrations above are for references only,Actual objects may look different in person.

Before You Install
Dimensional drawing, water pressure check
Confirm dimensions of product with installation space Confirmation of water pressure

• The minimum dynamic operating water pressure is 35 psi, and the maximum static water pressure

Determination method for minimum water flow

Open the angle valve for water supply.
The measured water flow for 10.57GPF/min.
※ If the above conditions cannot be met, the best flushing effect cannot be achieved and an additional booster pump is required to increase the pressure.
( Tools: stopwatch, measuring cup.)

Installing Your Product
Install your unit as the following steps

1. Open the box right side up
   Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.

2. Mark your drainage hole with a cross
   Cardboard installation
   ● Align cardboard with the centerline of drain outlet;
   ● Draw contour line according to cardboard;

3. Mounting bracket installation
   ● Assemble the mounting bracket with bolts & and then install them to the pre- installed flange plate on the ground and lock tight with nuts.

4. Install the ceramic, water supply hoses and T-valve
   1. Place the wax ring on the drain hole at the bottom of the ceramic. 2. Install sealing flange into drain outlet;
   3. Install ceramic toilet on corresponding position according to contour line. Tips: The toilet is heavy, and it needs to open the seat cover to carry it bytwo people.
   4. Put the screw through the fixing sleeve and then install it through the holes(on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool;
   5. Put the decorative cap on the fixing sleeve.6. Attach the flush water hose to the T-valve and tighten.7. Attach the bidet water hose to the T-valve and tighten.8. Connect the T-valve to the water supply and tighten.
   Use gasket to prevent water leakage.9. Finish installation.

5. Installing the remote
   1. Drill two 6mm(0.24 inch) diameter holes on the wall (about 1.77 in deep)
   2. Knock the anchors into the hole with a hammer.
   3. Secure the holder with anchors.
   4. Use the screws to secure the holder to the wall.
   5. Remove the battery cover from the backside of the remote to install batteries
   6. Once finished, remote is ready to be placed in its holder.
   Detailed steps shown in the diagram below:
   Please use proper mounting tools for special wall surfaces(such as wood, HDF, etc.)
   ※ The remote control holder should be installed away from the bidet’s spray trajectory.
   ※ The remote control holder should be installed within reach when seated on toilet.
   ※ Make sure there is nothing to block the transmission between the toilet and its remote.

6. Installing and replacing the battery
   Install and replace the emergency flushing battery
   1. Reach into the bottom of the toilet cover and lift the cover upward firmly;
   2. Remove the battery cover by unscrewing the screw with a crosshead screwdriver;
   3. Replace the new battery, shut the battery cover, and tighten the screw with a crosshead screwdriver;
   4. Place the toilet cover to the flat position and press down to fix the cover.
   ※ Please confirm the battery’s positive and negative poles. Please do not charge, disassemble, fire the battery, or mix with used batteries or different kinds of batteries to avoid liquid leakage or explosion.
   ※ The battery box has a moisture-proof function. Please ensure ‘ that the set screws are screwed in place to achieve a good seal  effect.
   ※ If the battery needs to be replaced, it is recommended to contact your local dealer to have it replaced by specialized personnel.
   When delivered from the factory, the battery has been installed in the battery box.

7. Testing water flow
   1. Fully open the angle valve as shown in the figure. 2. Confirm there is no leaks.
   In case of water leaking, unfasten the nuts and install them again.

8. Connecting power
   1. Connect to the grounding.
   2. Plug in AC 120V power plug. 3. Check if the power is on.
   (1) Check if the power light is on.
   (2) Powered on: Press and hold the knob for 3 seconds to enter the standby mode.

Testing the product
(test whether the functions of the buttons on the remote control and the knob on the side of the body are normal)

• Are all the functions working properly?
  Rear Wash,Front Wash (Including water pressure & nozzle position adjustment),Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleaning, Remote Control.
  All functions listed above should be tested.

• Checking Rear Wash Sey
  Hold the seat sensor area with your hand, turn the knob forward or press  2 the “Rear” button on remote control. Please place a cup or bowl in front of the nozzle to avoid water spraying and to keep from getting wet.

Matching your remote control code

※ When the product leaves the factory, the remote control and the product are connected, if the remote control went failure, please reconnect the code as following methods.

1. Unplug the product’s plug, press the stop key for few seconds until the level lights are flickered.

2. Plug in again when the remote control get closer to the product.

3. The level lights stop flickering. And then they are on.
   All the level lights are on.

4. The remote control and the toilet are re-connected.

< >

Under standby mode, when seated
“Rotated backward”, rotate it backwards for 45° to enter into front wash mode.
Default setting: oscillating front wash.
Operation cycle: front wash 1.5 mins + drying 4 mins + flushing once.
During front washing, turn the knob to adjust water pressure.| Under standby mode, when seated
“Rotated forward”, rotate it forwards for 45° to enter into rear wash mode.
Default setting: oscillating rear wash.
Operation cycle: rear wash 1.5 mins + drying 4 mins + flushing once.
During rear washing, turn the knob to adjust water pressure.
---|---

※ When starting up, short press the knob to send ceramic flushing command when there is no function.

• Auto flush
  It will automatically flush when user leaves the seat after toileting.
  The toilet will only flush once.

• Mi Kick Flush
  Touch “Foot button” gently.
  When not seated, approach the product and gently touch this button with your foot, and three foot-touch operations can be performed, i.e., the first time to open the cover, the second time to open the seat, and the third time to close the cover and seat and flush.
  ※ Please do not touch the button forcefully.
  ※ Rear/front wash is not available during flushing.

• Night Light
  It runs automatically around the ambient light.
  When the night light is turned on, it will automatically turn on/off the night light through the changes of intensity of the outside light. When the light is strong, the night light is automatically turned off, and when the light is weak, the night light is a utomatically turned on.

• UV Sterilization
  Irradia tion at the nozzle.
  10s after user unseats, UV sterilization will initiate automatically to work for 3 minutes.
  During this time, either press “stop” button or activate seat sensor can quit UV sterilizing.
  ※ Ultraviolet lamp device is installed inside smart toilet.

• Automatic Deodorization
  The function will operate automatically.
  The deodorization function will be activated when seating on the toilet, and will be closed after leaving the seat for 3mins.

• Mi Drying With Flush
  Press the “Dryer” button.
  The warm air function is activated and a flush is performed.
  ※ Rear/front wash is not available during flushing.

• Microwave induction
  Sensing distance:< 1m/3.3ft
  Automatically open the seat cover when the human body is near.
  ※ If the product can not detect the presence of human body for a period of time, it will automatically close the seat and cover.

• Digital Display
  When setting temperature of water/seat/dryer, the corresponding indicator lights up.

• Mi User-friendly Design
  ● Slow-closing lid/seat
  Preserve your toilet’s life and allows you to close the lid/seat silently.
  ● Water purification
  Equipped with dedicated filter to ensure your bidet will only spray clean, filtered water.
  ● Damper
  The product has installed the damper which provide the toilet cover and toilet seat with a buffer function, to achieve the mute effect.
  ● 8 Layers of safety
  8 different built-in safety features to protect the user and product.
  ● Memory mode
  By power off, water/seat/air temp, water pressure, nozzle position are all restored to mid-range, night light is under auto on mode. Power on/off, the toilet will keep the last setting status.
  ●  Self-cleaning Nozzle
  The washer can automatically clean, keeping bacteria and stains away.
  ● Pre-flush
  After seating, the toilet will flush once to moisten the bowl.

Maintenance
Regular maintenance is required to ensure normal use

NOTE

• Cut off the power and water supply before maintenance.
• Direct water wash to the entire product is prohibited.

WARNING
Do not spray water or detergents on the power cord. Doing so may .cause electrick shock or fire.

• Maintenance during Winter Season
  During winter season, the water inside may freeze after long periods of storage and non-usage. Please take measures to prevent.

NOTE

• Before connecting the product to the water supply and electrical outlet, allow it to defrost for 30 mins in a warm indoor environment.
• In cases of extreme cold/freezing/nozzle stuck in place, wrap the water input line with a warm towel. Never pour hot water or use a hot dryer directly on the toilet.

Troubleshooting

Troubleshooting
Experiencing issues with your product?
Find solutions below to solve your problems. Contact us if the problem persists.

Power Button

switch for 3s until the power light is on
Check whether there is electric leakage| Unplug from the outlet and re-plug in. If this doesn’t work, please contact us

Wash Functions

Wait for the water supply
Check whether or not the angle valve switches off| Open the angle valve
Check whether or not the water filter is blocked| Clean the filter mesh or change the water filter
Check whether or not the inlet pipe is flexed| Straighten the hose to eliminate the flex
Poor cleaning performance| Check if the water pressure is set at lowest level| Reset the water pressure
Check whether or not the inlet filter is blocked| Clean the filter mesh or change the water filter
Unusual water flow from the nozzle| Abnormal operation| Unplug for one minute and then re-plug in
The water temp is not warm enough| Check if the water temp is set at lowest level| Reset the water temperature
Leaking nozzle| Solenoid valve failure| Please contact us directly for return and exchange
Bidet cleaning can not work| Human inducation system failure| Please contact us directly for return and exchange

Dryer

the air temperature
Check whether or not the heating element of dryer is damaged| Please contact us directly for return and exchange

Heated Seat

Remote Control

batteries
Remote control is not working| Remote control got wet| Wipe off water and let it dry

Toilet Unit

directly for return and exchange
No water but have the sound of flushing| 1. Check wether the hose is bended
2. Check there is any damage of water pump
Keep flushing| Please contact us directly for return and exchange

Soft-Closing Feature

1. Re-plug in
2. If it doesn’t work, please contact us directly for return and exchange

Specifications

10.57GPF/min
Maximum pressure| 108psi (static state)
Toilet| Flush type| Tornado Flush
Rough-in| Rough-in 12in
ashing| Heating type| Instant heating
Temp of warm water| Off/93.2°F-102.2°F(4 levels)
Safety devices| Butterfly thermostat, thermal fuse, flow sensor
Dryer| Dryer temp range| Off/95°F-131°F(4 levels)
Safety devices| Thermal Fuse, bi-Metal
Heated Seat| Heat temp range| Off/93.2°F-102.2°F (4 levels)
Safety devices| Thermal Fuse
Remote control| Dimension| 7.48in(L)x2.01 in(W)x0.87in(H)
Battery| Two AAA Batteries
Power cable length| Appx.47.24in

**** ※

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>