Casta Diva CD-BT05 Electronic Toilet Seat User Manual
- June 16, 2024
- Casta Diva
Table of Contents
CD-BT05 Electronic Toilet Seat
User Manual
SAFETY PRECAUTIONS
IMPORTANT SAFEGUARDS
When using electrical products, especially when children are present, basic
safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
DANGER- To reduce the risk of electrocution:
- Do not use while bathing.
- Do not place or store product where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- Do not reach for a product that has fallen into water. Unplug immediately.
WARNING- To reduce the risk of burns, electrocution, fire, or injury to persons.
- Close supervision is necessary when this product is used by, on, or near children or if nvalids.
- Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properif it has been dropped or damaged, or dropped into water. Return the product to a servicenter for examination and repair.
- Keep the cord away from heated surfaces.
- Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hairand the like.
- Never use while sleeping or drowsy.
- Never drop or insert any object into any opening or hose.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Connect this product to a properly grounded outlet only. See Grounding Instructions.
- Do not use while bathing.
- Risk of Electric Shock. Connect Only to a Grounding Type Receptacle Protected by a Ground-Fault Circuit-Interrupter (GFCI)
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit,
grounding reduces the risk of electric shock by providing an escape wire for
the electric current. This product is equipped with a cord having a grounding
wire with a grounding plug. The plug must be plugged into an outlet that is
properly installed and grounded DANGER- Improper use of the grounding plug can
result in a risk of electric shock.
If repair or replacement of the cord or plug is necessary, do not connect the
grounding wire to either flat blade terminal. The wire with insulation having
an outer surface that is green with or without yellow stripes is the grounding
wire.
Check with a qualified electrician or serviceman if the grounding instructions
are not completely understood, or if in doubt as to whether the product is
properly grounded.
IMPORTANT! READ ALL INSTRUCTIONS BEFORE USING
Please carefully read this manual before use and keep for future reference.
The following cons are used in this manual to ndicate varying severities of
hazards. Please abide by these precautions, otherwise serious consequences may
occur.
NOT ATION
| Please pay close attention to avoid serious harm or accidents.
---|---
If not attentive, body or property damage may result.
Caution! Comply with guidelines .
Prohibited action!
Do not dismantle!
Keep away from direct contact with water or any liquid .
Do not touch this area!
Do not touch this area with wet hands!
Keep away from fire!
Operate as instructed.
Please unplug!
Please confirm it is grounded!
WARNING
Make sure the power supply is grounded.
- Otherwise, electric shock may occur.
- Please consult qualified electrician or serviceman if the power supply is not grounded.
Do not touch or plug in the cord with wet hands.
- Otherwise, electric shock may occur.
Do not connect power cord if the cord is damaged or broken.
- Otherwise, electric shock or fire may occur.
The product must be connected to standard voltage power source (AC120V±10%,Max Current 16A).
- Otherwise, electric shock or fire may occur. CD
Do not forcefully pull, break, bend, strip, twist, or over squeeze the power cord and cable.
- Otherwise, electric shock or fire may occur.
The cord must be replaced by authorized personne l
- Otherwise, electric shock or fire may occur.
Please avoid installing the product while bathroom is wet. Do not splash water on the product .
- Otherwise, electric shock, fire, damage may occur.
Do not place lit cigarettes or other ignited items on the product.
- Otherwise, fire may occur.
Do not place lit cigarettes or other ignited items on the product.
- Otherwise, the device may be damaged or malfunction.
When the seat or lid is broken, please unplug the power and shut down the
water supply.
- Otherwise, electric shock or fire may occur.
Unplug and clean the dust on the power cord with a dry cloth regularly.
- Otherwise, fire may occur due to bad nsulation.
Individuals who are handicapped (physically, mentally, or emotionally) must be accompanied during use.
- Otherwise, long-term use may cause ow-grade burns . Children should not play with this product.
- Otherwise, injury may occur.
Only Authorized personnel such as a qualified electrician should service the product. Do not dismantle this product to repair or remodel.
- Otherwise, malfunctions may cause electric shock, fire, or injury.
Do not urinate on the product.
- Otherwise, electric shock may occur.
Do not use polluted water supply.
- Otherwise, the water may damage the device or harm the user.D
ATTENTION
If using any chemical toilet bowl cleaner, be sure to wipe up any spills that spash onto the plastic areas of the product. Do not use any acidic chemical detergent. Only neutral detergents are permitted .
- Otherwise, the plastic may break and cause body damage, electric shock, or fire.
Please do not let water or detergent wet the bidet qtoilet seat or power plug .
- Otherwise, there may be a risk of electric shock or fire.
Do not stand, sit, or lean forcefully on the lid of the idet toilet seat. Do
not open or close the lid/seat ring forcefully to avoid damage. Do not block
the dryer door with hands or other objects. Do not cover the door during use.
WARNING
Do not use warm or heated temperature settings for extended periods of
time.
Please make sure the user is fully seated (see image below). Otherwise, the
cleaning or drying function will stop.
Do not urinate on the nozzle.
- Otherwise, the nozzle may become obstructed.
Please use provided accessories to install the device. Do not use old parts.
- Otherwise, eakage may occur.
During power failure, unplug the device and close the water supply valve to
prevent leaking.
Do not expose to direct sunlight or heating device.
Do not use a timer power source or external switch to turn the device on/off.
The thermal cutoff device may cause danger.
Please turn off the water supply before replacing he filter. Firmly attach
the filter before opening the water supply.
- Otherwise, leakage may occur.
Please unplug and close water sources to the device when away for extended periods of time.
- Otherwise, leakage or fire may occur.
In very low temperatures, the water within the device may freeze after long periods of disuse. To avoid damage, please warm the unit to melt the ice.
PARTS DIAGRAM
PRODUCT OVERVIEW
CONTROL PANEL
PRODUCT INSTALLATION
PARTS INCLUDED
After opening the package, please confirm
that you have received all parts listed above. If you are missing any parts,
please contact us.
BEFORE INSTALLATION
IMPORTANT! Before nstalling the product, please make sure that you meet
all the requirements listed below.
Power Requirements
- The power rating should be within the required range (AC 120V ± 10%, Max current 16A above)
- The distance between power outlet and bidet should be 3.9 ft. Keep the bidet away from water .
- This product must be grounded.
- The wiring should be installed by a professionally licensed electrician.
- Please do not plug in the product before installation is complete to prevent malfunction.
Water Requirements
- The minimum dynamic water pressure required is 11.6psi.
- The maximum static water pressure required s 101.5psi .
- Water pressure below the min or above the max range will affect the performance of the product.
Sizing Requirements
-
Please measure your toilet to make sure that there is enough space for the bidet (20.43 in long).
-
The distance between the 2 mounting holes must be within 4.72-6.89in .
-
The distance from the filter to the bidet inlet should be 23.62 n or less .
-
The distance between the mounting holes and the edge of the toilet bowl must be within 17.99-19.72 in.
*The product has no Ground Fault Circuit Interrupter. It should be
connect to outlet with Ground Fault Circuit Interrupter. Otherwise, the
accidental failure of this product may result in the loss of life or property.
INSTALLATION STEPS
- Install the electronic bidet seat
1. Remove the existing toilet seat.
(a) Remove the toilet seat mounting bolts.
(b) Remove the existing toilet seat from the toilet.
2. Insert the inflated rubber tube set into the mounting holes on
the toilet bowl. 3. Place the Fixed Card on the toilet bowl where the mounting
holes are. Make sure that the wash I dry gates are close to the rim and
pointed down 4. Install the fixing plate
(a.) Place metal washers on the inflated tubes.
(b.) Place the fixing plate in the rectangle space of the fixed card.
(c.) Place the adjustment sheet on the fixing plate.
(d.) Insert and tighten the screws.5. Install the electronic toilet seat
(a.) Remove Fixed Card.
(b.) Press the push button and slide the seat into the fixing plate.
(c.) Adjust the seat for best fit. Loosen the screws for adjustment when needed.-
Install the filter and hoses
-
Turn on the water
1. Turn the water supply on. The angle valve should be fully open.
2. Check for leaks. Make sure there is no leakage. If there is leaking from any connection, re-install the part. -
Connect power
1. Plug into the outlet (120V) . 2. Confirm the power connection.
(a) Press and hold the power button for O.Ss to turn on the bidet seat.
(b) The spray strength ndicator on the control panel should light up when the bidet turns on.
-
**PRODUCT OPERATION
**
BASIC FUNCTIONS
- Functions will only work when user is seated on the bidet seat.
- Dryer will automatically stop after 4 minutes.
 PRODUCT OPERATION
OTHER FUNCTIONS
RESTORING FACTORY SETTINGS- To restore the product to the original factory settings, pull the plug from the wall, wait 1 minute, then reconnect the plug. The Water Temp, Seat Temp, Dryer Temp, Spray Strength, and Nozzle Position will restore to the original Middle level settings.
SELF CLEANING NOZZLE
- The washer can automatically clean, keeping bacteria and stains away.
MAINTENANCE
- Before maintenance, please unplug the power source and shut off the water supply .
- Regular maintenance is required to ensure that the product operates at optimum efficiency.
Maintenance of Lid, Seat, and Plastic Parts
- Wipe the lid, seat, and plastic parts with a wet soft cloth (water).
- Please wipe with water frequently or the product will become hard to clean later f the dirt and debris s not removed on time. Wiping with water can also help prevent static electricity from generating around the product, which can cause the product to accumulate dust and become dirty.
- For a deeper clean, the bidet can be removed from the toilet to access the surface beneath. To remove the bidet, press the catch plate button located on the right side of the bidet, then lift the bidet slightly to extract. (do not remove the bidet forcefully).
Maintenance of Steel Mesh Filter
- For your health, as well as optimal performance of the bidet, please clean or replace the filter regularly.
- If you notice that the water pressure is becoming weaker, please wash or replace the filter.
- Please make sure to turn off the water supply completely before removing the filter. Attach the new filter securely to avoid leakage.
- Turn the coin counterclockwise to open the filter and use a brush to clean.
Maintenance of the nozle
- Press “Water Temp” for 3 seconds without occupying the seat, the nozzle will extend and can be cleaned with a soft brush.
- Do not try to pull the nozzle out with force, or the nozzle may break.
ATTENTION
Do not spray water or detergent on the bidet, remote ncontrol, or power cord.
- Otherwise, electric shock or fire may occur.
WARNING
While cleaning the plastic parts, do not use strong, acidic chemical cleaners
(concentrated sulfuric acid, nitric acid, glacial acetic acid, carbon
tetrachloride, chloroform, acetone, butyl ketone, benzene, toluene, phenol,
cresol, methyl ether, methyl formamide, soybean oil, vinegar, 40% nitric acid,
hydrochloric acid, 95% alcohol liquor, gasoline, kerosene, brake oil, etc.).
Please only use neutral cleaners.
- Otherwise, the plastic may break, and cause body damage, electric shock, or fire.
TROUBLESHOOTING
- If you experience any of the problems below, please follow the suggested solutions. If you continue to experience issues after trying the solutions, please consult with a qualified electrician or serviceman.
Power button
| Problem | Possible Causes | Possible Solutions |
|---|---|---|
| Bidet is not working | Blackout or loose plug | Check the power supply |
| Power off (Power indication light not on) | Press Power/Stop button until |
indication light turns on
Electric leakage| Unplug the power cord then re-connect. If it doesn’t work,
contact us
Wash functions
| Problem | Possible Causes | Wait for the water |
|---|---|---|
| Water does not spray | No water supply | Possible Solutions |
| Water supply is turned off | Turn water supply valve to turn on water | |
| Filter is stuck | Clean or replace filter | |
| Water hose is twisted | Stretch hose | |
| Water pressure is weak | Water level is set to LOW | Adjust water pressure |
| Filter is stuck | Clean or replace filter | |
| Spray is off-center | Operational failure | Unplug device and re-plug in after 1 |
min
Water is not warm| Water temp. is set to LOW| Adjust water temp
Leaking| Parts are loose or damaged| Re-install the bidet seat.
If it doesn’t work, please contact us
Wash function does noactivate| No skin contact with seat sensor| Make sure you
seat right on the sensing area.
Body sensor is broken| Contact us
Dryer
| Problem | Possible Causes | Adjust dryer temp |
|---|---|---|
| Dryer is not warm | Dryer temp. is set to OFF | Contact us |
| Dryer s broken | Enable dryer again | |
| Dryer stops during use | Dryer will stop after 4 mins running. | Possible |
Solutions
Heated Seat
| Problem | Possible Causes | Adjust seat temp |
|---|---|---|
| Seat temp. not warm | Seat temp. is set to OFF | Possible Solutions |
Other
| Problem | Possible Causes | Contact us |
|---|---|---|
| Lid or seat closes fast | Damper s broken | Possible Solutions |
Functions work in turns
nonstop| QA testing model activated| Unplug device and re-plug n after 1 min
PRODUCT INFORMATION
SPECIFICATIONS
| Model Number | CD-BTO5 |
|---|---|
| Rated Voltage | 120V- |
| Frequency | 60Hz |
| Rated Power | 1140W |
| Environmental Temp | 39.2°F-104°F |
| Water Inlet Environment | 39.2°F-95°F |
The range of water
inlet pressure| Minimum necessary
water pressure| 11.6p5i, ensuring the water flow at least 0.61GPF/10s
Maximum water
pressure| 101.5psi (in a static condition)
Flushing| Way for heating| Instant heating
Temp pf warm water| Off/about 93.2°F-102.2°F
The length of power line| About 47.24in
The size of product| 20.43inx17.72inx5.24in
Part no./ Fuctions| CD-BT OS
---|---
Aerated Wash| •
Unlimited wash| •
Rear Wash| •
Front Wash| •
Automatic Wash| •
Oscillating Wash| •
H/C Massage| •
Water Pressure Adjustable| •
Nozzle Position Adjustment| •
Water Temp Adjustable| •
Self-cleaninq Nozzle| •
Nozzle Cleaning Mode| •
Seat Heating| •
Air Dryer| •
Soft Close| •
Seat Temp Adjustable| •
Air Temp Adjustable| •
Night Light| •
Instant Heating| •
Seat Sensor| •
Memory Mode| •
Auto Start| •
Air isolation| •
Eight Safety Protections| •
Antibacterial Seat| •
Notice. represents that the product have this function.
CONTACT US
If you have any questions or comments, please feel free to reach out to our
customer care at any time and we will be able to assist you further. Thank you
for choosing us.
E-mail:SERVICE@CASTADIVAHOME.COM
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>