Casta Diva CD-Y060 Elongated Smart Bidet Toilet Instruction Manual

June 10, 2024
Casta Diva

Casta Diva CD-Y060 Elongated Smart Bidet Toilet

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-
product

Thank you for purchasing our product. Please read this manual before installation and use to ensure that your product will function at peak performance. Read this manual thoroughly and store in a safe place for future references.

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING

WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons.

  1. Close supervision is necessary when this product is used by, on, or near children or i nvalids.
  2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
  3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
  4. Keep the cord away from heated surfaces.
  5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
  6. Never use while sleeping or drowsy.
  7. Never drop or insert any object into any opening or hose.
  8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
  9. Connect this product to a properly grounded outlet only. See Grounding Instructions.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS
This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

DANGER
Improper use of the grounding plug can result in a risk of electric shock.

If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.

Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. This product is factory equipped with a specific electric cord and plugs to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel.

If it is necessary to use an extension cord, use only a three-wire extension cord that has a three-blade grounding plug, and a three-slot receptacle that will accept the plug on the product.Replace or repair a damaged cord.

Functions

The functions may vary from different parts no

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(1\) Casta-Diva-CD-Y060-Elongated-Smart-
Bidet-Toilet-fig- \(2\)

Notice: represents that the product have this function.

Parts Information

Overview, Sideview, Remote controller

Overview

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(3\)

Rotated Switch

Remote Controller

TIP: When it is turned on and off the seat, press the “Nozzle Clean+ H/C Massage” button on the remote.

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(5\) Casta-Diva-CD-Y060-Elongated-Smart-
Bidet-Toilet-fig- \(6\)

Warnings and Safety

Please read thoroughly
First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference.

The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be held liable for any injuries to the user and damages to the product due to improper usage and/or failure to heed safety warnings.

Explanation of Terms and Symbols

  • Warning
    Indicates possible injury resulting from improper usage due to negligence of this sign.

  • Attention
    Indicates human injury or property loss that may result in improper usage due to negligence of this sign.

  • Note When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions.

  • Prohibits any individual from performing any action with this symbol.

  • Prohibits any individual from dismantling the product.

  • Keep product away from any wet environments, including, but not limited to, humid environments, and close proximities to baths, showers or sinks.

  • Do not touch!

  • Do not touch it with a wet hand!

  • Keep away from any extreme heat or fire!

  • operate only as instructed!

  • Pull out the power plug!

  • Protective grounding

Warning

This product needs to be properly grounded.

  • Risk of electric shock
  • If unsure, contact an electrician. electrical installation company.
  • Do not touch, insert or pull out the power plug with a wet hand.
  • Risk of electric shock.
  • Do not use a power socket in poor condition or a damaged power plug.
  • Risk of fire and/or electric shock.
  • The power socket in use should be within the specified range (AC120V ). Risk of fire and/or electric shock.
  • Do not pull, damage, bend, twist, stretch, roll, bundle, clamp or squeeze the power cable. Do not place anything on the power cable.
  • Risk of fire and/or electric shock
  • If the power cord is damaged, to prevent any injuries or accidents, it should be replaced by a professional.
  • Risk of fire and/or electric shock
  • Do not place a lit cigarette along with other burning objects into the unit.
  • Risk of fire.
  • Do not use during thunderstorms (pull out the power plug during storms). Failure in doing so may lead to injury or fault in the product.
  • When the seat ring or the cover plate is damaged, to avoid any harm, be sure to pull off the power plug, close the water source and contact your local distributor for replacement.
  • Risk of fire or electric shock.
  • Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth.
  • Risk of fire.
  • Any person with a disability, the elderly, and children, should be using this product with the supervision of another individual.
  • Be advised that sitting on the heated seat for an extended amount of time may result in burns.
  • This product is not a toy. Advise children not to play with product.
  • Risk of injury.
  • Do not dismantle, repair or alter this product on your own. Call in a professional, or contact Dyconn Faucet for further advice.
  • Risk of fire, electric shock, and/or other accident that may lead to injury.

Warning

For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. These include, but are not limited to products such as: concentrated sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetrachloride, chloroform, acetone, butanone, benzene, methylbenzene, phenol, methyl phenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc).

Risk of damaging parts that can lead to accidents and injuries

Do not add water or detergent into the unit or on to the wireless remote. Do not soak the product with water or cleaner.

  • Risk of fire and/or electric shock.

Do not install product in a humid environment or a soak room. Do not spray or soak this product with any form of liquid to prevent any damage to the product.

  • Risk of fire and/or electric shock.

Do not use polluted water or water meant for industrial.

  • Risk of urocystitis or dermatitis. Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.

Do not apply any force to the unit’s seat and lid. Do not stand on the lid or open 0 or close the lid and the seat forcefully.

  • This may result in product damage and/or user injury.

Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use.

  • Risk of fire, electric shock, and/or other accident that may lead to user injury.
  • Do not spray urine at the dryer trap.
  • Risk of electric shock.

Read the following for proper battery usage.

  • Properly install the battery according to its correct polarity.
  • Remove the battery during long periods without use.
  • Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals.
  • cover the battery with tape before disposal.
    • This will prevent battery fluid leaks that may cause fire and/or other damages.

Warning

  • ePlace the battery out of children’s and infants’ reach.
    If the battery is swallowed, contact a doctor immediately. elf battery fluid leaks onto the user, quickly rinse off the area using water.

  • If battery fluid gets into your eyes, do not rub your eyes. Quickly rinse it with water and consult a doctor immediately.

    • May result in vision impairment or blindness.

When the battery is in use, do not do the following operations.

  • Do not hold or store with metal objects (such as a necklace or a watch).
  • Do not mix new and old batteries.
  • Do not pull the battery apart battery or throw it into water and/or fire. Battery fluids may cause a fire.

Attention
Droy enro tte umspee trhaetu hreea ftoerd a sne eaxt toern wdeadrm

  • Eoxutennt doefd t iumsee. may result in burns.

While sensor the operate using the area. skin is this incorrect? Otherwise, product, contact with make the product the sure my seat

  • While using this product, make sure that the skin is in contact with the seat sensor area. Otherwise, product may not operate correctly.
    • Children and smaller individuals may have trouble staying in contact with sensor area.

Do not spray urine in the direction of the bidet nozzle.

  • Doing so may result in blockage to the bidet nozzles and cleaning area.

In case of sudden power failure, remove the power plug and close the angle valve to prevent water leakage.

  • Risk of water leakage and/or property loss/damage.
  • Avoid direct sunlight or heat.
    • Risk of product discoloration.
  • Do not supply electricity with an external switch. le: connecting the universal part to a timer switch.
    • Run the risk of issues caused by improperly resetting the thermal breaker.
  • When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed, be sure to fasten it with force.
    • Risk of water leak
  • Pull out the power plug when the product is in disuse for an extended amount of time. Make sure to shut off the water and remove the water inside the product.
    • Risk of fire, leaks, and product damage.
  • When storing or transporting in cold climates, make sure to remove all water from the unit. The product may crack and other damages may occur due to freezing water.
    • Risk of fire, leaks, and product damage.

Required tools

Required tools for installation. Please have these tools prepared prior to installation.

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(14\)

Item list (Confirm that all below items are inside the box)

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(15\)

  • Please confirm all the aforementioned items are inside the package.
  • If there are any omissions, please contact our customer service.
  • The illustrations above are for reference only, Actual objects may look different in person.
  • If your water valve is 3/8, you could directly connect the T-valve; If your water valve is 1 /2, please screw off the adapter, then connect it.

Before you Install

Water pressure check, dimensional drawing

Dimensions

Confirm dimensions of product with installation space

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(16\)

  1. Open the box right side up
    Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(17\)

  2. Mark your drainage hole with a cross

  3. Align the flange with the drain hole, and mark the positions of the four mounting holes of the flange on the ground with a marking pen.

  4. Place the toilet on the ground by aligning the ground drain hole, place two fixing blocks in the openings on the left and right sides of the toilet bottom, mark the screw mounting hole positions of the fixing block with a marking pen, and then remove the toilet.Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig- \(19\)

  5. Put the flange on the drain hole, and fix it on the ground with four bolts. Then Seal the flange with glass glue.

  6. Place the fixing block on the installation position marked by the line drawing pen and fasten it with two bolts.

  7. Install the ceramic body, water supply hose and water filter

  8. Place the wax ring on the drain hole at the bottom of the ceramic.

  9. Align the ceramic drain with the drain hole on the ground, and press down to make the wax ring fully contact with the ground.

  10. Fix the two sides of the ceramic with two bolts, and finally install the cap.

  11. Attach the flush water hose to the T-valve and tighten it.

  12. Attach the clean water hose to the T-valve and tighten.

  13. Connect the T-valve to the water supply and tighten it. Use a gasket to prevent water leakage.

  14. Finish installation.

  15. Installing the remote

  16. Drill two 6mm(0.24 inch) diameter holes on the wall (about 1.77 in deep)

  17. Knock the anchors into the hole with a hammer.

  18. Secure the holder with anchors.

  19. Use the screws to secure the holder to the wall.

  20. Remove the battery cover from the backside of the remote to install the batteries

  21. Once finished, the remote is ready to be placed in its holder.
    Detailed steps are shown in the diagram below:

  * Please use proper mounting tools for special wall surfaces(such as wood, HOF, etc.)
  * The remote control holder should be installed away from the bidet’s spray trajectory.
  * The remote control holder should be installed within reach when seated on the unit.
  * Make sure there is nothing to block the transmission between the toilet and its remote.  

Steps:Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(29\)

  1. Installation and replacement of power outage flush battery
    Installation of power outage flush battery

  2. Take out the connecting wire (as shown in the figure)

  3. Connect the waterproof DC plug and tighten the waterproof cap.

  4. Place the battery box in a proper position as shown in the figure.

  5. The battery and connecting cable have positive and negative poles. Do not forcibly insert them. Otherwise, the product will be damaged
    Replacement of power outage flushing battery

  6. Contact after-sales customers to purchase new batteries.

  7. Loosen the scre on the battery cover, remove the old battery, and hand It to a professional organization for recycling.

  8. Install the battery in a proper position according to the battery installation picture

  • Open the water supply angle valve to the maximum as shown in the figure.
  • Confirm various connecting parts are not water leaking.
    • In case of water leaking, unfasten the nuts again and install them again.
  1. Connect to the grounding.
  2. Plug-in AC 120V power plug.
  3. Check to see if the power is on.
  4. Check to see if the power light is on. If not, push the reset button.
  5. Once the power light is on, the toilet will run its initial diagnostics: lights will turn on, the cleaning nozzle will extend, the motor will begin to run and water will run through the system. Once the light is off, the self-diagnostic is complete.
  6. Press the side power button, and confirm the toilet is powered on.

Testing the product (Checking the side panel buttons and remote control)

  • Are all the functions working properly?
    Posterior Wash, Front Wash (Including water pressure & nozzle position adjustment), Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleaning, Anion Deodorization, and remote control.
    All functions listed above should be tested.

  • Checking posterior wash
    Place your hand on the sensor point (shown in the illustration on the right), and press Posterior on the Side Control Panel or the wireless remote. Use your hand to block the nozzle spray.

Matching your remote control code
When the product leaves the factory, the remote control and the product are connected, if the remote control went failure, please re-connect the code as the following methods.

  1. Unplug the product’s plug, and press the stop ket for a few seconds until the level light is flickered.
  2. Plug the attaching plug when the remote control get closer to the product.
  3. The level light stops flickering, and then it is lighted on.
  4. At the time, the remote control and product is re-connected.

Function Explanations

Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig-
\(38\)

When starting up, short-press the knob to send ceramic flushing command when there is no function.

Auto flush

  • When the seat sensor no longer detects a user, it will automatically flush.
  • The toilet will only flush once.

Foot touch

Touch “Foot touch” gently.
When the seat cover is closed, tap the foot to open the cover. When the seat cover is closed and opened, tap the foot to open the seat. When the seat cover is opened, tap the foot to close the seat cover and flush once.

  • Please do not touch the button forcefully.
  • Posterior/front wash is not available during flushing.

Light Sensor

It runs automatically around the ambient light.
When the night light is turned on, it will automatically turn on/off the night light through the changes in the intensity of the outside light. When the light is strong, the night light is automatically turned off, and when the light is weak, the night light is automatically turned on.

UV Sterilization

After leaving the seat, it will run automatically.
Operate it automatically when leaving the seat. The cleaning spout will be back in position, and the UV function will be activated after 10s, and it is working for 3min, After seating, the UV function will stop, and the indicator will go out.

  • An ultraviolet lamp device is installed on the smart toilet.

Deodorization

  • The function will operate automatically.
    The deodorization function will be activated when seating on the toilet, and will be closed after leaving the seat for 3mins.

Microwave induction

  • It is about 1 meter close to the product.
  • Automatically open the seat cover when the human body is near.
    • If the product can not detect the presence of the human body for a period of time, it will automatically close the circle and cover.

Dryer

  • Dries front and rear.
  • Press “Dryer” once. Press the “Dryer” button again.

Blackout flush

  • When the product is not plugged into the power supply, short press to flush.
  • Can realize power outage flushing function.
  • If the preceding operations do not work, replace the battery or contact the storage system Local dealers.

User-friendly Design

  • Slow-closing lid/seat
    Preserve your toilet’s life and allows you to close the lid/seat silently.

  • Water purification
    Equipped with a dedicated filter to ensure your bidet will only spray clean, filtered water.

  • Damper
    The product has installed the damper which provides the toilet cover and toilet seat with a buffer function, to achieve the mute effect.

  • 8 Layers of safety

  • 8 different built-in safety features to protect the user and product.

  • Memory mode
    After a power failure, water temp, water pressure, seat temp, and wand position are all restored to mid-range after power failure. The night light is turned on by default after a power failure. On / off, keep the last memorized setting state.

Maintenance

Regular maintenance is required to ensure normal use

Note

  • Cut off the power and water supply before maintenance.
  • Direct water wash to the entire product is prohibited.

Maintenance of product surface and ceramics

  • Wipe dust or stains with a soft wet cloth
  • A wet soft brush, cloth or sponge may be used to clean the ceramic area
    • Do not use abrasive cleaning solutions, such as alcohol, bleach, paint thinner, cresol, benzene, gasoline, etc.

WARNING
Do not spray water or remote detergents control on the or toilet, power cord. Doing so may cause electrical shock or fire.

Maintenance during Winter Season
During winter season, the water inside may freeze after long periods of storage and non-usage. Please take measures to prevent this.

Note

  • Before connecting the product to the water supply and electrical outlet, allow it to defrost for 30 mins in a warm indoor environment.
  • In cases of extreme cold/freezing/nozzle stuck in place, wrap the water input line with a warm towel. Never pour hot water or use a hot dryer directly on the toilet.

Maintenance of the nozzle
Powered on and not seated: Press the “Nozzle Clean” button on the remote controller, and the washer will automatically extend. If there is dirt in the nozzle orifice, If there is dirt in the nozzle orifice, you can gently hold the washer with one hand and clean it with a toothbrush with the other hand.

  • Do not use excessive force, otherwise, it will damage the nozzle.
  • When the nozzle is clogged, it is recommended to replace it with a new one. Casta-Diva-CD-Y060-Elongated-Smart-Bidet-Toilet-fig- \(50\)

Troubleshooting

Experiencing issues with your product?
If the user should run into any issues, please consult the troubleshooting guide below. If the problem persists, please contact a professional.

Power button

 |

Fault Diagnoses

|

Solutions

---|---|---
Not working| Check whether the attaching plug is loose or not|

Please check the circuit

Check whether the power is switching on or off (the power light is not on)| Press rotated switch for 3s, the power light is on.
Check whether there is any electric leakage or not (the light of leakage protection plug is not on)| Unplug the attaching plug from the socket, plug it again later. Press the reset switch of the

leakage protection plug, if it is still not working, please unplug the attaching plug and

contact with local distributor to repair.

Wash functions

  Fault Diagnoses Solutions
No water from the spout
Check whether or not the water supply cuts off Wait for the water supply to

be restored
Check whether or not the angle valve switches off| Open the angle valve
Check whether or not the water filter is blocked| Clean the filter mesh or change the water filter
Check whether or not the inlet pipe is flexed| The inlet pipe must be straight
The intensity of cleaning is not strong enough| Check whether or not the water pressure of cleaning switch to low level or not| Regulate the water pressure according to the instruction manual
Check whether or not the inlet filter is blocked| Clean the filter mesh or change the water filter
Unusual water

flow from the spout

| Abnormal operation| Unplug the attaching plug for one minute and then plug it again
The water temp is not warm enough| Check whether or not the water supply switches to low level| Regulate the water temp according to the instruction manual
The cleanser is always leaking| Solenoid valve no longer has any effect| Please contact with our qualified maintenance personnel for repairing
The cleaning function is not working normally| The human induction system of the toilet seat no longer has any effect| Please contact with our qualified maintenance personnel for repairing

Dryer

  Fault Diagnoses Solutions

The dryer blows cold air

| Check whether or not the dryer switches off| Regulate the temperature of dryer according to the instruction manual
Check whether or not the heating element of dryer is damaged| Please contact with our qualified maintenance personnel for repairing

Heated seat

  Fault Diagnoses Solutions

The seat temp is too low or is not hot

|
Check whether or nor the temp of toilet seat is on the “off” position| Regulate the temperature of toilet seat according to the instruction manual

Remote Control

  Fault Diagnoses Solutions
The blue light of water temp is flickered
Low battery Please replace a new battery
Remote control is not working Check whether or not there is any water on the
remote control Wipe off water by dry towel

Toilet Unit

  Fault Diagnoses Solutions

The product is not flushed clean

|
No power supply| Power restoration
No water from the spout| Please contact with our qualified maintenance personnel for repairing
No water but have the sound of flushing| 1. Check whether or not the pipeline is blended or not, please keep the water supply pipeline open and smooth

2. Check there is any damage of water pump

have water all the time

| Please contact with our qualified maintenance personnel for repair if there is any unusual from the water inlet valve.

Soft-Closing Feature

  Fault Diagnoses Solutions

The function of flipping the seat cover/ring up by foot touch cannot open or close| ****

Auto-damping is damaged

| 1. Recharge after unplug the attaching plug

2. Please contact with our qualified personnel if the following solution is not working.

Specifications

Rated voltage 120V-
Frequency 60Hz
Rated power input 10S0W(When inlet water temp in 59 °F)
Seat and water temperature range 93.2 °F-104 °F
Dryer temperature range 95°F -131°F
Water supply hose type DNlS(Gl/2″)
Toilet Flush type
Rough-in Rough-in 12in

Flushing

| Heating Type| Instant heating
Temp of Warm Water| Off/93.2°F -102.2°F (4 levels)
Safety devices| Butterfly thermostat, thermal fuse, flow sensor


Dryer

| Dryer temp range| Off/95 °F-131 °F(4 levels)
Airspeed| 4m/s
Safety devices| Thermal Fuse, bi-Metal
Heated Seat| Heat temp range| Off/93.2 ° F -104°F (4 levels)
Safety devices| Thermal fuse
Remote control| Dimension| 26.92inxl 5.66inxl 8.Sin
Battery| Two AAA Batteries
Power cable length| Appx.59in

E-mail: SERVICE@CASTADIVAHOME.COM.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals