Casta Diva CD-Y060 Smart Toilet Instruction Manual

Casta Diva CD-Y060 Smart Toilet

Dimensions

• Use: Bidet Seat for Toilets Model Number is the model.
• Energy Source: Type of Energy Source
• Water Pressure: Range of Water Pressure
• Water Temperature: Range is the water temperature.
• Seat Temperature: Range is the seat temperature.

Product Usage Instructions

Function Prompt Tones
To turn on/off all Function Prompt Tones (except Alert Tone), follow these steps:

1. Long press the ‘H/C Massage’ button on the remote control.
2. The Function Prompt Tones will be turned on if they were previously off, or turned off if they were previously on.

ECO Mode
To turn on/off ECO mode, follow these steps:

1. Long press the ‘Nozzle clean’ button on the remote control.
2. If seat heating is on and there are no operations for 30 minutes, ECO mode will be activated automatically.
3. In ECO mode, the seat temperature will lower automatically and maintain the lowest temperature setting.

Automatic Open &Close Lid Function
To turn on/off the automatic open&close lid function, follow these steps:

1. Press the ‘Nozzle Clean’ and ‘H/C Massage’ buttons simultaneously on the remote control.
2. The automatic open&close lid function will be turned on if it was previously off, or turned off if it was previously on.

FAQ (Frequently Asked Questions)

• Q: How do I turn off all Function Prompt Tones?
  A: Long press the ‘H/C Massage’ button on the remote control.

• Q: How do I turn on/off ECO mode?
  A: Long press the ‘Nozzle clean’ button on the remote control. ECO mode will be activated automatically if there are no operations for 30 minutes.

• Q: How do I turn on/off the automatic open &close lid function?
  A: Press the ‘Nozzle Clean’ and ‘H/C Massage’ buttons simultaneously on the remote control.

Product Name: Intelligent Toilet
Model: CD-Y060

• Thank you for purchasing our product. Please read this manual before installation and use to ensure that your product will function at peak performance.
• Read this manual thoroughly and store in a safe place for future references.
• E-mail: SERVICE@CASTADIVAHOME.COM

IMPORTANT SAFEGUARDS

When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following:

READ ALL INSTRUCTIONS BEFORE USING
WARNING-To reduce the risk of burns, electrocution, fire, or injury to persons.

1. Close supervision is necessary when this product is used by, on, or near children or invalids.
2. Use this product only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
3. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the product to a service center for examination and repair.
4. Keep the cord away from heated surfaces.
5. Never block the air openings of the product or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
6. Never use while sleeping or drowsy.
7. Never drop or insert any object into any opening or hose.
8. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

• DANGER- Improper use of the grounding plug can result in a risk of electric shock.
• If repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either flat blade terminal. The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire.
• Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded. This product is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician. If the product must be reconnected for use on a different type of electric circuit, the reconnection should be made by qualified service personnel.
• If it is necessary to use an extension cord, use only a three wire extension cord that has a three-blade grounding plug, and a three-slot receptacle that will accept the plug on the product.
• Replace or repair a damaged cord.

The functions may vary from different part no.

Notice:  represents that the product have this function.

User Friendly Design
Kick control, Radar sensor, New features to offer you an enjoyable experience

Parts Information

Overview, Sideview, Remote controller

Overview

Remote Control

TIPS:

1. Long press ‘H/C Massage’ to turn on/off all Function Prompt Tones (except Alert Tone)
2. Long press ‘Nozzle clean’ to turn on/off ECO mode. When seat heating is on, no operations <30mins, ECO mode is activated automatically. The seat temp will lower automatically and maintain the lowest temp setting. When needs to turn on/ off the automatic open & close lid function, please press “Nozzle Clean+ H/C Massage”
   button on the remote control.

Warnings and Safety

Please read thoroughly

• First of all, thank you for purchasing our product. To ensure proper and safe use of this product, carefully read this section prior to any usage. Afterwards, store this manual in a safe place for any needed future reference.
• The hazards and warnings listed herein are important to our user’s safety. Significant consequences may result from failure to heed warnings. The company will not be held liable for any injuries to the user and damages to the product due to improper usage and/or failure to heed safety warnings.

Explanation of Terms and Symbols

• Warning 1ndicates possible injury resulting from improper usage due to negligence of this sign.
• Attention 1ndicates human injury or property loss that may result in improper usage due to negligence of this sign.
• Note When used with the above “Warning” and “Attention” signs, indicates a strict request to follow noted precautions.
• Prohibits any individual from performing any action with this symbol
• Prohibits any individual from dismantling product.
• Keep product away from any wet environments, including, but is not limited to, humid environments, close proximities to baths, showers or sinks.
• Do not touch!
• Do not touch with a wet hand!
• Keep away from any extreme heat or fire!
• operate only as instructed!
• Pull out the power plug!
• Protective grounding

Warning

• This product needs to be properly grounded.

• Risk of electric shock

• If unsure, contact an electrician. electrical installation company.

• Do not touch, insert or pull out the power plug with a wet hand.

• Risk of electric shock.
  Do not use a power socket in poor condition or a damaged power plug.

• Risk of fire and/or electric shock.

• The power socket in use should be within the specified range (AC120V ).

• Risk of fire and/or electric shock.

• Do not pull, damage, bend, twist, stretch, roll, bundle, clamp or squeeze the power cable. Do not place anything on power cable.

• Risk of fire and/or electric shock
  If the power cord is damaged, to prevent any injuries or accidents, it should be replaced by a professional.

• Risk of fire and/or electric shock
  Do not place a lit cigarette along with other burning objects into the unit.

• Risk of fire.
  Do not use during thunderstorms (pull out the power plug during storms).

• Failure in doing so may lead to injury or fault in the product.

• When the seat ring or the cover plate is damaged, to avoid any harm, be sure to pull off the power plug, close the water source and contact your local distributor for replacement.

• Risk of fire or electric shock.
  Regularly pull out the power plug and wipe off any dust on the power plug using a clean dry cloth.

• Risk of fire.

• Any person with a disability, the elderly, and children, should be using this  product with the supervision of another individual.

• Be advised that sitting on the heated seat for an extended amount of time may result in burns.

• This product is not a toy. Advise children not to play with product.

• Risk of injury.
  Do not dismantle, repair or alter this product on your own. Call in a professional, or contact Dyconn Faucet for further advice.

• Risk of fire, electric shock, and/or other accident that may lead to injury.

Warning

• For cleaning or maintenance of plastic parts, do not use any harsh cleaning agents. (These include, but are not limited to products such as: concentrate sulfuric acid, concentrated nitric acid, glacial acetic acid, carbon tetrachloride, chloroform, acetone, butanone, benzene, methylbenzene, phenol, methyl phenol, dimethylformamide, methyl ether, soybean oil, acetate, 40% nitric acid, thick salt acid, 95% alcohol, gasoline, kerosene or brake oil, etc. ).
• Risk of damaging parts that can lead to accidents and injuries
• Do not add water or detergent into the unit or on to the wireless remote. Do not soak the product with water or cleaner.
• Risk of fire and/or electric shock.
• Do not install product in a humid environment or a soak room. Do not spray or soak this product with any form of liquid to prevent any damage to the product.
• Risk of fire and/or electric shock.
• Do not use polluted water or water meant for industrial.
• Risk of urocystitis or dermatitis. Untreated water may also cause corrode inner workings of unit and may cause electrical shock or a fire.
• Do not apply any force to the unit’s seat and lid. Do not stand on the lid or open (S) or close the lid and the seat forcefully.
• This may result in product damage and/or user injury.
• Do not place your hand or any other object into the dryer trap, and do not cover the dryer and dryer trap during product use.
• Risk of fire, electric shock, and/or other accident that may lead to user injury.
• Do not spray urine at the dryer trap.
• Risk of electric shock.

Read the following for proper battery usage.

• Properly install the battery according to its correct polarity.
• Remove the battery during long periods without use.
• Replace the battery before it reaches the end of its usage. Failure to do so may result in interrupted control signals.
• cover the battery with tape before disposal.
• This will prevent battery fluid leaks that may cause fire and/or other damages.

Warning

• Place the battery out of children and infant reach.
• If battery is swallowed, contact a doctor immediately.
• If battery fluid leaks onto user, quickly rinse off area using water.
• If battery fluid gets into eyes, do not rub your eyes. Quickly rinse it with water and consult a doctor immediately.
• May result in vision impairment or blindness.
• When the battery is in use, do not do the following operations.
• Do not hold or store with metal objects (such as a necklace or a watch).
• Do not mix new and old batteries.
• Do not pull battery apart battery or throw it into water and/or fire. Battery fluids may cause a fire.

Attention

• Do not use the heated seat or warm dryer temperature for an extended amount of time.
• Extended use may result in burns.
• While using this product, make sure that the skin is in contact with the seat sensor area. Otherwise, product may not operate correctly.
• Children and smaller individuals may have trouble staying in contact with sensor area.
• Do not spray urine in the direction of the bidet nozzle.
• Doing so may result in blockage to the bidet nozzles and cleaning area.
• Do not use your old hose component. Use the one provided with your product. Anything else connected to the older hose may need to be replaced.
• Risk of water leakage and/or property loss/damage.
• In case of sudden power failure, remove the power plug and close the angle valve to prevent water leakage.
• Risk of water leakage and/or property loss/damage.
• Avoid direct sunlight or heat.
• Risk of product discoloration.
• Do not supply electricity with an external switch. le: connecting the universal part to a timer switch.
• Run the risk of issues caused by resetting the thermal breaker.
• When the filter is being replaced, be sure to close the water supply angle valve. When the filter is being installed, be sure to fasten it with force.
• Risk of water leak
• Pull out the power plug when the product is in disuse for an extended amount of time. Make sure to shut off the water and remove the water inside the product.
• Risk of fire, leaks, and product damage.
• When storing or transporting in cold climate, make sure to remove all water  from the unit. Product may crack and other damages may occur due to freezing water.
• Risk of fire, leaks, and product damage.

Installation

Tools required for installation

Required tools
Required tools for installation. Please have these tools prepared prior to installation.

Item list (Confirm that all below items are inside the box)

• Please confirm all the aforementioned items are inside the package.
• If there are any omissions, please contact our customer service.
• Illustrations above are for references only, Actual objects may look different in person.
• If your water valve is 3/8, you could directly connect the T-valve; If your water valve is 1/2, please screw off the adapter, then connect it.

Before you Install
Water pressure check, dimensional drawing

Confirm dimensions of product with installation space

Checking your water supply
The lowest working water pressure is 11.6psi, the highest water pressure is 108.78psi, the toilet can not reach the best clean situation when the lowest water pressure can not reach 11.6psi.

Installing your product
Install your unit as the following steps

1. Open the box right side up
   Remove the accessories first, then remove the unit from the top, as shown in the diagrams below.

2. Mark your drainage hole with a cross
   Cardboard installation

3. Align cardboard with the centerline of drain outlet;

4. Draw contour line according to cardboard;

5. Mounting bracket installation
   Assemble the mounting bracket with bolts and then install them to the pre- installed flange plate on the ground and lock tight with nuts.

Install the ceramic, water supply hoses and T-valve

1. Place the wax ring on the drain hole at the bottom of the ceramic.
2. Install sealing flange into drain outlet;
3. Install ceramic toilet on corresponding position according to contour line.
4. Put the screw through the fixing sleeve and then install it through the holes(on both sides of the toilet ceramic) to the mounting bracket on the ground, and lock tight with a tool;
5. Put the decorative cap on the fixing sleeve.
6. Attach the flush water hose to the T-valve and tighten.
7. Attach the bidet water hose to the T-valve and tighten.
8. Connect the T-valve to the water supply and tighten. Use gasket to prevent water leakage.
9. Finish installation.

Installing the remote

1. Drill two 6mm(0.24 inch) diameter holes on the wall (about 1.77 in deep)
2. Knock the anchors into the hole with a hammer.
3. Secure the holder with anchors.
4. Use the screws to secure the holder to the wall.
5. Remove the battery cover from the backside of the remote to install batteries
6. Once finished, remote is ready to be placed in its holder.

Detailed steps shown in the diagram below:

• Please use proper mounting tools for special wall surfaces(such as wood, HDF, etc.)
• The remote control holder should be installed away from the bidet’s spray trajectory.
• The remote control holder should be installed within reach when seated on toilet.
• Make sure there is nothing to block the transmission between the toilet and its remote.

Installing and replacing the battery box

Installing the external battery box

1. Remove the connecting cables from the position where indicated.
2. Connect the waterproof DC power plug and tighten the waterproof cap.
3. Place the battery box in a suitable position as shown.
4. For any questions, please call the customer service center or your local dealer.

The battery should be placed out of the reach of children.
Some batteries and connecting wires may have slots. Please do not forcibly insert, otherwise, it will lead to product damage.

Replacing the external battery box

1. Unscrew the waterproof cap at the connection of the waterproof DC power plug.
2. Pull out the waterproof DC power plug.
3. Replace the battery box assembly with a new one, which
4. For any questions, please call the customer service center or your local dealer.

*The waterproof grade of battery box for power failure and flushing is ipx6, and a single battery box can meet the power failure and flushing times of about 200 times.

• Fully open the angle valve as shown in the figure.
• Confirm there is no leaks. In case of water leaking, unfasten the nuts  and install them again.
• Connect to the grounding.
• Plug in AC 120V power plug.
• Check if the power is on.
• Check if the power light is on. If not, press the reset button.
• Once the power light is on, the toilet will run its initial diagnostics: lights will turn on, cleaning nozzle will extend, the motor will begin to run and water will run through the system. Once the light is off, the self-diagnostic is complete.
• Powered on: Press and hold the knob for 3 seconds to enter the standby mode.

Testing the product

(test whether the functions of the buttons on the remote control and the knob on the side of the body are normal)

• Are all the functions working properly?
  • Rear Wash, Front Wash (Including water pressure & nozzle position adjustment),Heated Dryer, Water & Seat temperature Adjustment, Nozzle cleaning, Anion Deodorization, Remote Control.
  • All functions listed above should be tested.
• Checking Rear Wash
  Hold the seat sensor area with your hand, turn the knob forward or press the “Rear Wash” button on remote control. Please place a cup or bowl in front of the nozzle to avoid water spraying and to keep from getting wet.

Matching your remote control code
When the product leaves the factory, the remote control and the product are connected, if the remote control went failure, please re-connect the code as following methods.

1. Unplug the product’s plug, press the stop key for few seconds until the level lights are flickered.
2. Plug in again when the remote control get closer to the product.
3. The level lights stop flickering. And then they are on.
4. The remote control and the toilet are re-connected.

Function Explanations

When starting up, short press the knob to send ceramic flushing command when there is no function.

• Auto flush
  • It will automatically flush when user leaves the seat after toileting.
  • The toilet will only flush once.
• Kick Flush
  • Touch “Foot button” gently.
  • When not seated, approach the product and gently touch this button with your foot, and three foot-touch operations can be performed, i.e., the first time to open the cover, the second time to open the seat, and the third time to close the cover and seat and flush.
  • Please do not touch the button forcefully.
  • Rear/front wash is not available during flushing.
• Night Light
  • It runs automatically around the ambient light.
  • When the night light is turned on, it will automatically turn on/off the night light through the changes of intensity of the outside light. When the light is strong, the night light is automatically turned off, and when the light is weak, the night light is a utomatically turned on.
• UV Sterilization
  • After leaving the seat, it will run automatically.
  • Operate it automatically when leaving seat. The cleaning spout will back to position, and the UV function will be activated after 1 Os, and it is working for 3min, After seating, the UV function will stop and the indicator will go out.
  • Ultraviolet lamp device is installed inside smart toilet.
• Automatic Deodorization
  • The function will operate automatically.
  • The deodorization function will be activated when seating on the toilet, and will be closed after leaving the seat for 3mins.
• Microwave induction
  • Sensing distance:< 1 m/3.3ft
  • Automatically open the seat cover when the human body is near.
  • If the product can not detect the presence of human body for a period of time, it will automatically close the seat and cover.
• Drying With Flush
  • Press the “Dryer” button.
  • The warm air function is activated and a flush is performed.
  • Rear/front wash is not available during flushing.

User-friendly Design

• Slow-closing lid/seat
  Preserve your toilet’s life and allows you to close the lid/seat silently.

• Water purification

  • Equipped with dedicated filter to ensure your bidet will only spray clean, filtered water. pamper
  • The product has installed the damper which provide the toilet cover and toilet seat with a buffer function, to achieve the mute effect.

• 8 Layers of safety
  8 different built-in safety features to protect the user and product.

• Memory mode
  By power off, water/seat/air temp, water pressure, nozzle position are all restored to mid-range, night light is under auto on mode. Power on/off, the toilet will keep the last setting status.

• Self-cleaning Nozzle
  The washer can automatically clean, keeping bacteria and stains away.

• Pre-flush
  After seating, the toilet will flush once to moisten the bowl.

Maintenance

Regular maintenance is required to ensure normal use

Note

• Cut off the power and water supply before maintenance.
• Direct water wash to the entire product is prohibited.

Maintenance of product surface and ceramics

• Wipe dust or stains with a soft wet cloth
• A wet soft brush, cloth or sponge may be used to clean the ceramic area
• Do not use abrasive cleaning solutions, such as alcohol, bleach, paint thinner, cresol, benzene, gasoline, etc.

Maintenance of the nozzle

• Powered on and not seated: Press the “Nozzle Clean” button on the remote control, the spray wand will automatically extend. If there is dirt attached to the surface of the nozzle, clean it with a toothbrush. To remove the nozzle, gently hold the spray wand and disassemble the nozzle.
• Do not clean with excessive force, otherwise it will damage the nozzle.
• When the nozzle is clogged, it is recommended to replace it with a new one.

WARNING

Maintenance during Winter Season
During winter season, the water inside may freeze after long periods of storage and non-usage. Please take measures to prevent.

Note

• Before connecting the product to the water supply and electrical outlet, allow it to defrost for 30 mins in a warm indoor environment.
• 1n cases of extreme cold/freezing/nozzle stuck in place, wrap the water input line with a warm towel. Never pour hot water or use a hot dryer directly on the toilet.

Troubleshooting

Experiencing issues with your product?
Find solutions below to solve your problems. Contact us if the problem persists.

Power button

Phenomenon

Not working

| Fault Diagnoses
Check whether the plug is loose or not| Solutions
Check the power supply
---|---|---
Check whether the power is on (the power light is off)| Press the rotated switch for 3s until the power light is on
Check whether there is electric leakage (the light of leakage protection on plug is off)| Unplug from the outlet and re-plug in. Then press the reset button. If this doesn’t work, please contact us

Wash functions

Phenomenon|                   Fault Diagnoses Solutions|
---|---|---
No water from the nozzle|
Check whether or not the water supply cuts off| Wait for the water supply|
Check whether or not the angle valve switches off| Open the angle valve|
Check whether or not the water filter is blocked| Clean the filter mesh or change the water filter|
Check whether or not the inlet pipe is flexed| Straighten the hose to eliminate the flex|
Poor cleaning performance| Check if the water pressure is set at lowest level| Reset the water pressure|
Check whether or not the inlet filter is blocked| Clean the filter mesh or change the water filter|
Unusual water flow from the nozzle| Abnormal operation| Unplug for one minute and then re-plug in|
The water temp is not warm enough| Check if the water temp is set at lowest level| Reset the water temperature|
Leaking nozzle| Solenoid valve failure| Please contact us directly for return and exchange|
Bidet cleaning can not work| Human indication system failure| Please contact us directly for return and exchange|

Dryer

The dryer blows cold air| Check whether or not the dryer switches off| Reset the air temperature
---|---|---
Check whether or not the heating element of dryer is damaged| Please contact us directly for return and exchange

Heated seat

Phenomenon|                   Fault Diagnoses Solutions|
---|---|---
The seat temp is too low or is not hot|
Check whether or nor the temp of toilet seat is on the “off” position| Reset the seat temperature|

Remote Control

Phenomenon|                   Fault Diagnoses Solutions|
---|---|---
The blue light of water temp is flickered|
Low battery| Please replace 2 new AAA batteries|
Remote control is not working| Remote control got wet| Wipe off water and let it dry|

Toilet Unit

Phenomenon|                   Fault Diagnoses Solutions|
---|---|---
Poor flush performance|
No power supply| Power restoration|
No water supply| Turn on water supply. If doesn’t work, please contact us directly for return and exchange|
No water but have the sound of flushing|

1. Check weather the hose is bended
2. Check there is any damage of water pump

|
Keep flushing| Please contact us directly for return and exchange|

Soft-Closing Feature

Phenomenon|                   Fault Diagnoses Solutions|
---|---|---
Auto open/close seat & cover don’t work by foot touch|
Auto-damping failure|

1. Re-plug in
2. If it doesn’t work, please contact us directly for return and exchange

|

Specifications

0.61GPF/1Os
Maximum pressure| 108.78psi (static state)
Toilet| Flush type| Tornado Flush
Rough-in| Rough-in 12in
Washing| Heating Type| Instant heating
Temp of Warm Water| Off/93.2°F-102.2°F(4 levels)
Safety devices| Butterfly thermostat, thermal fuse, flow sensor
Dryer| Dryer temp range| Off/95°F-131°F{4 levels)
Safety devices| Thermal Fuse, bi-Metal
Heated Seat| Heat temp range| Off/93.2°F-102.2°F(4 levels)
Safety devices| Thermal fuse
Remote control| Dimension| 7.48in(L)x2.01in(W)x0.87in(H)
Battery| Two MA Batteries
Power cable length| Appx. 59.06in

electrolux.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>