LifeBasis MT200A5-4 Transfer Machine User Manual

May 15, 2024
LifeBasis

LifeBasis MT200A5-4 Transfer Machine User Manual

LifeBasis MT200A5-4 Transfer Machine User Manual

Preparation And Overview

Open packaging box and check: no broken and each part below is Included.

LifeBasis MT200A5-4 Transfer Machine User Manual - Preparation And
Overview

Operation Panel Introduction

DEEPNESS I: The key is to set the copied documents by DEEPNESS I. The effect of the transfer pattern is lighter. When the DEEPNESS I works , the DEEPNESS II light goes off.
DEEPNESS II: The key is to set the copied documents by DEEPNESS II. The effect of the transfer pattern is darker. When the
DEEPNESS II works , the DEEPNESS I light goes off.
PHOTO: The key shifts between two kinds of resolution: PHOTO and FINE. When the resolution is PHOTO, the photo light works. MIRROR: The key shifts between two kinds of function: Mirror Copy and Normal Copy. The default situation is Mirror Copy. When the mirror function starts, the Mirror light works.
STOP: The key is to stop the copy function.
COPY: The key is to start the copy function.
POWER: The light indicates that the machine is prepared for working.
ERROR: The light is to show something wrong happened on the machine. When the TPH is overheating, the light goes on.

How To Use

Insert the power plug into an available power outlet. When the machine is in the standby situation, the sound “doo” will be heard. All the parameters items can be set up when the machine is under the standby situation.
Open the transfer paper cover. How to use tattoo transfer paper ? Method of Use 1: Universal Version Remove the stencil paper (between white paper and blue paper). Keep the yellow paper on top, blue paper in the middle and white paper at the bottom. Line and shaded patterns can be transferred. If you want a deeper transfer pattern, please choose Deepness 2 mode. (As shown the picture 1)

Method of Use 2: Professional Advanced Version A. For Simple Line Patterns, remove the stencil paper (between white paper and blue paper) and yellow paper. Keep the white paper on top, blue paper at the bottom. Choose Deepness 1 or 2 mode to transfer the pattern. If paper jam, please place the blue paper on top, the white paper at the bottom. (As shown the picture 2)

B. For Shaded Patterns, remove the stencil paper (between white paper and blue paper) . Keep the yellow paper on top, blue paper in the middle and white paper at the bottom. If you want a deeper transfer pattern, please choose Deepness 2 mode. (As shown the picture 1)
Close the transfer paper cover. Keep document needed to copy facing down as putting it into the feeder. When document is seized by the machine, please press the button “COPY”.

NOTE:
If you want to stop the copying mission, please press the button “STOP”. If the warning signal sounds and ERROR light works, the machine will stop copying immediately. If you need to pull out the power plug, please press the panel on the power socket.

How To Calibrate The Machine

The image sensor and thermal sensor in the machine are sensitive to the brightness and the temperature of the surrounding environment and will naturally change over time. When there is a big difference in shade between the copied picture and the original picture, please perform scanning calibration in time. The steps are as follows:

  1. Hold the “STOP” button for 3 seconds, you can hear one “beep” made by the machine and the all indicator lights are on.
  2. Insert a sheet of smooth A4 paper into the document feeder and press the “MIRROR” key to perform the scanning calibration.
  3. During the calibration process, the white paper is automatically fed and the scanning calibration is finished after the white paper is completely spit out.
  4. Hold the “STOP” key for 3 seconds, you can hear one “beep” made by the machine and all the indicator lights are restored, that is, the calibration is completed.

Select The Copy Mode According To The Original

You can select different copy modes by setting different key combinations on the panel according to the type of the actual original picture.

LifeBasis MT200A5-4 Transfer Machine User Manual - Select The Copy
Mode

How To Adjust The Scanning Shade And Printing Shade

You can adjust the scanning shade and printing shade of the machine according to the actual needs. The steps are as follows:

  1. Hold the “STOP” button for 3 seconds, you can hear one “beep” made by the machine and the all indicator lights are on.
  2. Press the “STOP” button to adjust the scanning shade with the one “beep” for the darkest of scanning and the lightest for seven “beeps”.
  3. Press the “COPY” button to adjust the printing shade with the one “beep” for the lightest of printing and the darkest for seven “beeps”.
  4. Hold the “STOP” button for 3 seconds, you can hear one “beep” made by the machine and all the indicator lights are restored, that is, the scanning and printing shade adjustments are completed.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals