dellonda DH103 Mini Keg Euro Beer Tap and CO2 Regulator User Manual
- June 1, 2024
- dellonda
Table of Contents
dellonda DH103 Mini Keg Euro Beer Tap and CO2 Regulator
Specifications
- Product Name: Dellonda Mini Keg Euro Beer Tap and CO2 Regulator
- Model No.: DH103
- Max. Pressure: 25psi
Product Information
Thank you for choosing the Dellonda Mini Keg Euro Beer Tap and CO2 Regulator. This product is manufactured to a high standard to provide you with years of trouble-free performance when used correctly and maintained properly.
Product Usage Instructions
Initial Setup
- Ensure all components are clean before use to meet hygiene requirements.
- Connect the tap handle (10) to the tap (9) securely.
- Attach the regulator/cartridge carrier (7) to the keg ensuring the delivery tube (3) touches the bottom of the keg.
- Secure the black ball lock connection (4) and grey ball lock connection (5) to the keg.
- Ensure the gas cartridge is correctly placed and tightened in the regulator/cartridge carrier (7).
Pouring Beer
- Ensure the tap is closed.
- Turn on the regulator and set it to the desired pressure (recommended 3-5psi).
- Open the tap handle slowly to pour beer. Adjust pressure if needed for optimal pouring.
Maintenance
- Clean any sediment from internals if experiencing slow delivery or gas leakage.
- Replace the gas cartridge if there is a lack of foaming/discharge or if the cartridge does not pierce.
- Regularly clean and dry all components after each use for best performance.
FAQ
Symptoms & Solutions
- Symptom: Lack of foaming and/or discharge. Gas leakage
- Solution: Replace gas cartridge. Re-tighten cartridge carrier.
- Symptom: Slow delivery
- Solution: Clean any sediment from internals. Replace gas cartridge.
- Symptom: Gas cartridge does not pierce
- Solution: Reposition cartridge and retighten.
- Symptom: Too much foam
- Solution: Turn off regulator, pull pressure release valve ring. Set regulator to 3 -5psi.
Dellonda Limited, Sole UK Distributor of Baridi, Kempson
Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
Contact: 01284 757575
Email: support@dellonda.co.uk
Website: www.dellonda.co.uk
Dellonda Mini Keg Euro Beer Tap and CO2 Regulator
Model No. DH103
Thank you for purchasing a product from the Dellonda range. Manufactured to a
high standard, this product will, if used according to these instructions, and
properly maintained, give you years of trouble free performance.
Important Information
Please read these instructions carefully and note any safe operational requirements, warnings & cautions. Use the product correctly and with care for the purpose for which it is intended. Failure to do so may cause damage and/or personal injury and will invalidate the warranty. Keep these instructions safe for future use.
GENERAL SAFETY
- DO NOT remove keg until fully empty.
- DO NOT remove gas cartridge until fully empty.
- DO NOT cover the unit while working.
- DO NOT place in direct sunlight.
- Children should be supervised at all times around this equipment.
INTRODUCTION
304 Stainless steel beer faucet with pressure releasing valve. The kit works at 25psi maximum that can be controlled to pour the perfect beer. 5-8psi is suggested to dispense beer. The pack comes with a set of spare seals and suction tube. 16g CO2 threaded canister sold separately.
- Works with Baridi model no.s: DH99, DH101, DH104 and many other branded kegs/growlers that accept an M33 x 1.5mm thread.
- SPECIFICATION
- Model no: DH103
- Noise Power/Pressure: Max. 25psi
CONTENTS
| 1 | Head Unit |
|---|---|
| 2 | O-Ring seal |
| 3 | Delivery tube |
| 4 | Black ball lock connection |
| 5 | Grey ball lock connection |
| 6 | Connector |
| 7 | Regulator/Cartridge Carrier |
| 8 | Shank adaptor |
| 9 | Tap |
| 10 | Handle |
| 11 | Safety valve (25psi) |
ASSEMBLY
- Assemble items 9 and 10 and screw assembled items to item 8.
- Screw assembly to item 4.
- Push the assemble items (above) onto the inlet on item 1.
- Assemble items 5, 6, and 7 and push assembled items onto the inlet on item 1.
- Fit item 3 to inlet on item 1 ensuring full engagement.
- Cut tube (item 3) to suit keg height. Make sure tube touches bottom of keg.
OPERATION
- Read this document thoroughly and assemble the unit accordingly.
- Check that the unit is fully assembled and installed in the appropriate location.
- Place item 2 into port inside neck of growler and screw fully assembled unit (item 1) onto growler ensuring a good fit.
- Ensure that valve on item 7 is fully closed.
- Fit gas canister (not supplied) into item 7 and screw tightly. A light ‘pop’ will be heard when the canister is punctured.
- Adjust pressure to suit using the regulator on item 7.
CLEANING AND MAINTENANCE
- Cleaning the internals of the unit is imperative to meet hygiene requirements. Clean before first use or long periods of non-use.
- Clean internals ONLY with warm, clean water.
- Cleaning the unit when changing is also recommended to improve your drinking experience.
- Disconnect the gas feed hose from the dispensing unit and hold the tap in the open position. Rinse through with clean, warm water, force water through the tube and out through the tap. Repeat until satisfied that the unit is clean.
- DO NOT use abrasive or chemical cleaning materials on any surface of the unit.
- Wipe interior and exterior surfaces with a damp cloth and dry thoroughly with a clean dry cloth.
- For more soiled surfaces use a neutral detergent, wipe down with a clean damp cloth and dry thoroughly with a clean dry cloth.
TROUBLESHOOTING
| Symptom | Solution |
|---|---|
| Lack of foaming and/or discharge. | Replace gas cartridge |
| Gas leakage | Re-tighten cartridge carrier |
| Slow delivery |
- Clean any sediment from internals.
- Replace gas cartridge
Gas cartridge does not pierce| Reposition cartridge and re- tighten.
Too much foam| Turn off regulator, pull pressure release valve ring. Set
regulator to 3 -5psi.
Environment Protection, Waste Electrical and Waste
Electronic Equipment Regulations (WEEE)
Recycle unwanted packaging materials. When this product is no longer required,
or has reached the end of its useful life, please dispose of in an
environmentally friendly way. Drain any fluids (if applicable) into approved
containers, in accordance with local waste regulations. It is our policy to
continually improve products and we reserve the right to alter data,
specifications and parts without prior notice. No liability is accepted for
incorrect use of this product. Guarantee is 12 months from purchase date,
proof of which is required for any claim.
Dellonda Limited, Sole UK Distributor of Baridi
Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757575 support@dellonda.co.uk
www.dellonda.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>