LifeBasis PTH-5 CO2 Monitor User Manual
- June 15, 2024
- LifeBasis
Table of Contents
CARBON DIOXIDE
MONITOR
PTH-5 USER MANUAL
Please read this manual carefully before using the product and keep it
properly.
Thank you for purchasing the carbon dioxide monitor PTH-5! This product uses a
carbon dioxide sensor based on the principle of non-dispersive infrared
absorption, which can accurately measure the concentration of carbon dioxide
in the air with a concentration range of 0 ppm to 5000 ppm.
Long-term inhalation of high concentration of carbon dioxide by the human body
can easily induce hypoxic suffocation . This product can keep you away from
these troubles. It is suitable for cars, baby rooms, homes, Offices and other
densely staffed occasions.
Packing List
- CO2 monitor × 1
- User manual × 1
- USB cable × 1
Specification
- Using non-dispersive infrared technology (NDIR), full-scale temperature range correction;
- Various air quality warning forms such as indicator lights and facial comfort expressions;
- Large-capacity 18650 lithium battery, long battery life;
- Support USB charging method;
- There is a bracket stand on the back of this product, which is convenient to place on a flat surface for continuous monitoring.
Precautions:
-
What should I do after receiving the goods?
Read instructions. Fully charge the product first. Then placing the product in a ventilated place, operate calibration (manual calibration is recommended). -
What to do in case of failure of product?
Make sure the product is fully charged and use the product after calibration. If the problem still cannot be resolved, please contact customer service: contact@lifebasis.com.
Special statement:
The illustrations of the products, accessories and user interface in the
manual are all schematic diagrams and are for reference only. If there is a
difference between the actual product and the schematic diagram due to product
updates and upgrades, please refer to the actual product received and the
manufacturer will not notify you separately.
Product Operation Instruction
-
Product Introduction
-
Charging and Battery Life
1.Use USB cable with a 5V, 1A adapter, in general, it takes 4-6 hours to fully charge. (This data is for reference only, the actual time will be affected by various factors)
2.Battery Life: Continuously use of the display, it can be used for 24 hours. While standby state (non-continuous use of the display), can be used for 36 hours.
3.When using a third-party USB cable, Please use qualified chargers. please avoid using a charging cable that exceed 1m in length, to prevent excessive voltage drop from being unable to recharge.
4.The following is a comparison of icon display and battery status.
LCD | Status |
---|---|
Icon displays | Full |
Icon flicker | Charging |
Icon flicker | Low power |
-
How to calibrate?
There are two calibration methods, manual calibration and automatic calibration. The operation steps are as follows:
1.Manual calibration: When the product is turned off, place the product in a ventilated place, and press the A and B buttons at the same time to enter the manual calibration mode. The screen will display a countdown of 200 seconds. When the countdown is completed, the manual calibration is completed.
2.Automatic calibration: After 24 hours of continuous charging, put the product in a ventilated place, the sensor of the product will trigger the first automatic calibration. Note: As long as the product is turned on for the first time, the automatic calibration
will be triggered again every 7 days, and the sensor will continuously correct itself. -
Button
Button| Operation| PTH-5
---|---|---
A| press and hold for 3 seconds| Power on / off
Press| Switching temperature units between C & T
B| press and hold for 3 seconds| Set screen state: screen backlight off after 10 minutes / stay on
Press| Backlight on/off
A+B| Press at the same time| Place it in a ventilated place, press the A and B buttons together for manual calibration. The process is completed after 200 seconds countdown.
Description:
- Power-saving function: In the screen backlight off state, the indicator status is the breathing light effect, and the user can wake up the backlight by short pressing any button. After the backlight is awakened each time, if there is no button operation continuously, the product will automatically turn off the screen backlight after 10 minutes , But the indicator light still detect the current air quality.
- First time, press and hold the B button for 3 seconds, the screen enter into backlight-off state after 10 minutes. Second time, press and hold the B button for 3 seconds, the screen enter into backlight stay on state. It cycle afterwards.
Alert
Whether the Carbon dioxide value exceeds the standard is indicated by the expression icon and indicator light, as shown in the following table:
When the measured value is between 0-700ppm, the Carbon dioxide value belongs
to the safe range;
When the measured value is between 700-1500 ppm, the Carbon dioxide value
belongs to the warning range and needs close observation;
When the measured value exceeds 1500ppm, the Carbon dioxide value exceeds the
standard and must be open the window for ventilation.
You can also directly judge whether the formaldehyde value exceeds the
standard through the indicator light. The following is the comparison table of
indicator light color and its meaning:
Light | Meaning |
---|---|
Green | Good |
Yellow | Normal |
Red | Bad |
Specifications
The following table provides the specifications of the measurement parameters
Specification | PTH- 5 |
---|---|
Temperature Range | -10~40°C(±1°C) |
Humidity Range | 20%-80%(±5%RH) |
Carbon dioxide value | Resolution:1 ppm; Range:0 ~ 5000 ppm |
Power Supply | 18650 lithium battery / 2400 m Ah |
Indicator light | |
Input | DC 5 V 1 A |
Size | 83 × 83 × 32 mm |
Notice
- This product should not be dipped in water, nor should it be placed in a high temperature environment exceeding 60℃.
- This product belongs to precision measuring instrument and shall not be dismantled without authorization.
- It can not be measured in the environment of organic gas with too high concentration for a long time.
- Built-in lithium battery, when measuring the air quality in the car, please do not put the carbon dioxide monitor with lithium battery in the sun;