CHIEF MSBV VESA Interface Bracket Instruction Manual

June 4, 2024
Chief

CHIEF MSBV VESA Interface Bracket

CHIEF-MSBV-VESA-Interface-Bracke-product-image

DISCLAIMER

Legrand | AV and its affiliated corporations and subsidiaries (collectively “Legrand | AV”), intend to make this manual accurate and complete. However, Legrand | AV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Legrand | AV makes no representation of warranty, expressed or implied, regarding the information contained herein. Legrand | AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® is a registered trademark of Legrand AV Inc.
DEFINITION S MOUNTING SYSTEM:
A MOUNTING SYSTEM is the primary Chief product to which an accessory and/or component is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief product which is attached to a primary Chief product, and may have a component attached or setting on it.
COMPONENT :
A COMPONENT is an audiovisual item designed to be attached or resting on an accessory or mounting system such as a video camera, CPU, screen, display, projector, etc.

WARNING:
A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION:
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING:
Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component.

WARNING:
Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the MSBV does not exceed 125 lbs (56.7 kg).

WARNING
Use this component only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING:
Never operate this component if it is damaged. Return the component to a service center for examination and repair.

WARNING:
Do not use this component outdoors.

NOTE:
The MSBV interface bracket is compatible with the following VESA patterns:

  • 100 x 100mm
  • 200 x 100mm
  • 200 x 200mm
  • 300 x 100mm
  • 300 x 200mm
  • 400 x 200mm

IMPORTANT ! : The MSBV interface brackets are designed to be mounted to a:

  • Listed Chief MCD6000 dual ceiling mount;
  • Listed Chief MCS6000 single ceiling mount.

SAVE THESE INSTRUCTIONS

Installation Instructions

DIMENSIONS

CHIEF-MSBV-VESA-Interface-Bracke-01

LEGEND
TOOLS REQUIRED FOR INSTALLATION

CHIEF-MSBV-VESA-Interface-Bracke-02

PARTS
Guidelines for Using Spacers (if required)

If the display has a recessed mounting surface, protrusions or a power box, a spacer must be placed between the display and MSBV bracket (A) and longer mounting hardware must be used. (See Figure 1)

IMPORTANT !
: Proceed to the correct procedure for installation of MSBV based upon the display’s mounting pattern.

INSTALLATION

WARNING: IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display. Properly sized screws will easily and completely thread into display
mounting holes. If spacers are required, be sure to use longer screws of the same diameter.
100 x 100mm Pattern

  1. Select four properly sized M4 screws from Bag A.
  2. Attach the MSBV bracket (A) using the hole pattern on back of display and holes noted at “X”. (See Figure 2)
  3. To prevent equipment damage, do not over-tighten the screws into the display.

200 x 100mm Pattern

  1. Select six properly sized M4 screws from Bag A.
  2. Attach the MSBV bracket (A) using the hole pattern on back of display and holes noted at “X”. (See Figure 3)
  3. To prevent equipment damage, do not over-tighten the screws into the display.

300 x 100mm Pattern

  1. Select eight properly sized M4 screws from Bag A.
  2. Attach the MSBV bracket (A) using the hole pattern on back of display and holes noted at “X”. (See Figure )
  3. To prevent equipment damage, do not over-tighten the screws into the display

300 x 200mm Pattern

  1.  Select eight M5 or M6 screws from Bag B or Bag C.
  2. Attach the MSBV bracket (A) using the hole pattern on back of display and holes noted at “X”. (See Figure 5)
  3. To prevent equipment damage, do not over-tighten the screws into the display

400 x 200mm Pattern

  1. Select six M5 or M6 screws from Bag B or Bag C.
  2. Attach the MSBV bracket (A) using the hole pattern on back of display and holes noted at “X”. (See Figure 6)
  3. To prevent equipment damage, do not over-tighten the screws into the display.

Figure 6
200 x 200mm Pattern
Select the appropriate method for attaching mounting buttons directly to display, dependent on size of mounting screw required for your display.

  1. If mounting screw is M4, attach four mounting buttons (Q) using four shoulder washers (N), four M4 washers (M) and four M4 screws from Bag A. (See Figure 7)
  2. If mounting screw is M5 or M6, attach four mounting buttons (Q) using four M5 or M6 screws from Bag B or Bag
    C. **(See Figure 7)

**

  1.  If 200 x 200mm hole pattern is shifted high on the screen, attach the MSBV bracket (A) vertically with four M5 or M6 screws (Bag B or Bag C). (See Figure 8)

INSTALLING DISPLAY TO MOUNT

  1.  Install display to UL Listed Chief mount following instructions included with the mount.

8800-002592 Rev032021 Legrand | AV www.legrandav.com 07/2021

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Chief User Manuals

Related Manuals