CHIEF MSBU Medium Universal Interface Bracket Instruction Manual
- June 4, 2024
- Chief
Table of Contents
MSBU Medium Universal Interface Bracket
Instruction Manual
DISCLAIMER
Legrand AV and its affiliated corporations and subsidiaries (collectively “Legrand.AV”), intend to make this manual accurate and complete. However, Legrand. AV makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Legrand.AV makes no representation or warranty, expressed or implied, regarding the information contained herein. Legrand.AV assumes no responsibility for the accuracy, completeness or sufficiency of the information contained in this document. Chief® is a registered trademark of Legrand AV Inc.
**DEFINITIONS
**
MOUNTING SYSTEM: A MOUNTING SYSTEM is the primary Chief product to which
an accessory and/or component is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief product that is attached
to a primary Chief product, and may have a component attached or setting on
it. COMPONENT : A COMPONENT is an audiovisual item designed to be attached
or resting on an accessory or mounting system such as a video camera, CPU,
screen, display, projector, etc.
WARNING: A WARNING alerts you to the possibility of serious injury or
death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction
of equipment if you do not follow the corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS!
WARNING: Failure to read, thoroughly understand, and follow all
instructions can result in serious personal injury, damage to equipment, or
voiding of factory warranty! It is the installer’s responsibility to make sure
all accessories are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength for this
accessory can result in serious personal injury or damage to the equipment! It
is the installer’s responsibility to make sure the structure to which this
accessory is attached can support five times the combined weight of all
equipment. Reinforce the structure as required before installing the
accessory.
WARNING: Exceeding the weight capacity can result in serious personal
injury or damage to the equipment! It is the installer’s responsibility to
make sure the combined weight of all components attached to the MSBU does not
exceed 125 lbs (56.7 kg).
WARNING: Use this accessory only for its intended use as described in
these instructions. Do not use attachments not recommended by the
manufacturer.
WARNING: Never operate this accessory if it is damaged. Return the
accessory to a service center for examination and repair.
WARNING: Do not use this accessory outdoors.
IMPORTANT! : The MSBU interface brackets are designed to be mounted to a
UL-Listed Chief medium flat panel mount:
- MFC Series cart
- MCD6000 medium dual display ceiling mount
- MCS6000 medium single display ceiling mount.
SAVE THESE INSTRUCTIONS
DIMENSIONS
LEGEND
| Tighten Fastener
---|---
| Loosen Fastener
| Phillips Screwdriver
| Hex-Head Wrench
TOOLS REQUIRED FOR INSTALLATION
PARTS
INSTALLATION
WARNING: IMPROPER INSTALLATION CAN LEAD TO THE MOUNT FALLING CAUSING
SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT! DO NOT substitute
hardware. Only use hardware provided or specified by the manufacturer.
-
Determine and mark the vertical center position between the Left side Upper and Lower mounting holes in display. (See Figure 1)
-
Determine and mark the vertical center position between the Right side Upper and Lower mounting holes in display. (See Figure 1)
-
Orient the vertical mounting bracket (R) so that mounting holes are on top and mounting slots are on the bottom. (See Figure 1)
-
Align mounting holes in the vertical mounting bracket (R) with upper and lower mounting holes in the display.
-
Adjust the vertical mounting bracket (R) position until the mark made in Step 1 aligns with a center mark in the vertical mounting bracket (R).
-
Select correct screws, nesting spacers (if necessary) and universal washers (if required) from the hardware bag (A-M) and attach brackets to the back of the screen. (See Figure 3)
IMPORTANT!: The M8 screws do NOT require a washer. Use the universal washer (MB) only with M4, M5, and M6 screws.
NOTE: The nesting spacers (MA) may be used separately, or put two together in different configurations to create different-sized spacers. (See Figure 2)
-
If the display has a recessed mounting surface, protrusions, or a power box, a spacer and longer mounting hardware must be placed between the display and the vertical mounting bracket (R). (See Figure 3)
-
Repeat Steps 3 through 6 for the Right side vertical mounting bracket using the same hole locations to align brackets horizontally.
-
Determine and mark the horizontal center position between the Left and Right TOP mounting holes in the display. (See Figure 4)
-
Determine and mark the horizontal center position between the Left and Right BOTTOM mounting holes in the display. (See Figure 4)
-
Orient the upper horizontal mounting bracket (Q) so that flanges are facing towards the display and resting in the recessed area of left and right vertical mounting brackets (R). (See Figure 4)
-
Adjust the Upper horizontal mounting bracket (Q) position until the center diamond in the horizontal mounting bracket (R) aligns with mark made in Step 9, and mounting holes and slots in the horizontal mounting bracket (Q) are aligned with threaded holes in mounting tabs of left and right vertical mounting brackets (R). (See Figure 4) and (See Figure 5)
-
Use a 1/8″ hex key (P) to secure the upper horizontal mounting brackets (Q) to left and right vertical mounting brackets (R) using four button head flanged screws (N). (See Figure 5)
-
Repeat Steps 10 through 13 for the lower horizontal mounting bracket (Q).
IMPORTANT ! : The orientation of, and mounting holes used when installing the lower horizontal mounting bracket must be the same as the upper horizontal mounting bracket. Vertically align upper and lower brackets by aligning holes or end of slots.(See Figure 5)
IMPORTANT! : Whenever possible install mounting screws diagonally as shown in detail in Figure 4 below. -
Install a display with an attached universal interface to mount following the installation instructions provided with the mount.
8800-002978 Rev02
©2021 Legrand | AV
www.legrandav.com
A6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>