cubetape C200S Dimensional Weight Scanner User Guide
- May 15, 2024
- cubetape
Table of Contents
cubetape C200S Dimensional Weight Scanner
Specifications
- Comms Timeout: 10 minutes
- Suffix DIM: TAB
- Suffix GEN: TAB
- Units: inches
- Output: Nearest inch
Product Usage Instructions
Set Outputs
Dimensional output is set to the nearest whole inch by default. To select alternative outputs, scan one of the Output codes below with the C200S:
- Output 0.1
- Output 0.25
- Output 0.5
- Output Nearest 1
- Output Next 1
Set Suffix
Select the preferred suffix for use with Dimensional (DIM) and General (GEN) items:
- Suffix Dim CR
- Suffix Dim TAB
- Suffix Gen CR
- Suffix Gen TAB
Additional suffixes and prefixes are available at www.cubetape.com/support.
Charge Battery
Insert the USB cable in the port under the flap by the Scan button and connect it to an adapter. If using the charge cradle, connect the USB cable and insert C200S. The red LED is ON when charging.
Power On C200S
Press the Scan button to power on the C200S.
Assembly Guide Rails
- The tape cassette has guide rails on both sides.
- The C200S Pod has guide grooves on both sides.
- The spring latch locks into the tape cassette.
- Align grooves and rails.
- C200S Pod slides down into the tape cassette.
- The latch in the C200S Pod locks into the tape cassette.
How to Measure
- Hook the tape end over the far edge of the package.
- Align the tape exit point to the near edge of the package.
- Press the Scan button to record and transmit the measurement.
Host Connections
C200S can connect to a host system using RF Dongle or Bluetooth. The default method is RF Dongle.
Connect to Windows using RF Dongle:
Pair the USB port, the LED will turn blue when connected.
Other Host Connections:
For all other host connections including CubeiQ and Bluetooth, scan the FAQ URL QR code with a mobile Android or iOS device or go to www.cubetape.com/support for instructions.
(FAQ)
- Q: Where can I find the full user manual?
- A: You can find the full manual at www.cubetape.com/support.
IN THE BOX
SET OUTPUTS
Dimensional output is set to the nearest whole inch by default. To select
alternative outputs scan one of the Output codes below with the C200S
SET SUFFIX
Select the preferred suffix for use with Dimensional (DIM) and General (GEN)
items.
Additional suffixes and prefixes available at www.cubetape.com/support
REFERENCES AND RESOURCES
For Scan to Pair and NFC Pairing instructions go to FAQ URL or Configuration guide. For the full manual go to www.cubetape.com/support For support email [email protected]
US DEFAULTS
To return to C200S US default settings at any time scan barcodes below
ASSEMBLY
- The tape cassette has guide rails on both sides.
- The C200S Pod has guide grooves on both sides.
- The spring latch locks into the tape cassette.
- Align grooves and rails.
- C200S Pod slides down into the tape cassette.
- The latch in the C200S Pod locks into the tape cassette
CHARGE BATTERY
Insert the USB cable in the port under the flap by the Scan button and connect it to the adaptor or if using a charge cradle, connect a USB cable and insert C200S. The red LED is ON when charging.
POWER ON C200S
Press the Scan button to power it on.
REGISTRATION
Scan the Registration URL QR code with a mobile Android or iOS device or visit www.cubetape.com/register to register your device.
HOW TO MEASURE
- Hook the tape end over the far edge of the package.
- Align the tape exit point to the near edge of the package.
- Press the Scan button to record and transmit the measurement.
HOST CONNECTIONS
C200S can connect to a host system using RF Dongle or Bluetooth. The default
method is RF Dongle.
Connect to Windows using RF Dongle:
- Power on C200S.
- Scan Pair, LED will flash green.
- Insert the dongle in a spare Windows USB port, the LED will turn blue when connected.
- Dimensions and barcodes will now be sent to the active Windows app
Other Host Connections
For all other host connections including CubeiQ and Bluetooth, scan the FAQ URL QR code with a mobile Android or iOS device or go to www.cubetape.com/support for instructions.
Scan the Registration QR code or visit www.cubetape.com/register to register your device