CubeTape C200 Dimensional Weight Scanner User Guide
- June 11, 2024
- cubetape
Table of Contents
CubeTape C200 Dimensional Weight Scanner
Introduction
This guide provides comprehensive information for the setup, configuration and maintenance of the C200 Scanning-Dimensioning device. It contains shortcuts for end users, configuration barcodes for system management, communication options, data and transmission formats, dimensioning units and output, and supported software information. Also available for download at www.cubetape.com/support is the scan engine parameter programming guide which provides complete guidance to programming the scan engine to meet specific symbology requirements.
Factory default settings are
| Settings | Factory Defaults |
|---|---|
| Communication Mode | HID over wireless 2.4G using a dongle |
| Keyboard | English |
| Workflow | Single Item (1DIM) |
| Suffix for Dimensional Items | TAB |
| Suffix for General Items | TAB |
| Source Prefix | OFF |
| Units | inches |
| Output | Nearest inch |
| Sleep TIme | 10 minutes |
| LED Aimer | ON at reading |
| Tape Cassette | 16 ft / 5 m with QR symbology |
Communication and Pairing Options
Barcodes and dimensions captured on C200 can be sent to a connected system using one of the following methods
- Windows connection using a wireless USB dongle
- Windows or Android connection using Bluetooth Direct (HID) Mode
- Windows or Android connection using Bluetooth Application (SPP) Mode
- Apple iOS connection using Bluetooth BLE Mode.
C200 ships with two other pairing utilities to simplify the pairing process
- NFC Pairing is initiated when a user brings the NFC Reader of their mobile device into close proximity with the C200 scan head. Follow the Android prompts to complete pairing.
- Scan to Pair initiates pairing when C200 scans a pairing barcode displayed on the mobile device screen.
- This option may need to be coordinated with 3rd party software vendors.
Behavior
LED
Description of the basic functions of the indicator LED
| LED | Description |
|---|
Blue LED
| Connection Status:
ON when connected OFF when disconnected
Green LED
| Decode Indicator:
Flashes once on successful data scan and transmission
Flashes three times if scanning is successful but transmission fails
Red LED
| Charge Indicator:
ON when charging
OFF when fully charged or not charged
Indicator LED combination description
| LED | Description |
|---|---|
| Blue LED OFF, Green LED flashes | 2.4G mode pairing status |
| Green LED OFF, Blue LED flashes | SPP mode pairing status |
| Green and Blue LED flash alternately | HID mode pairing status |
Buzzer
| LED | Description |
|---|---|
| Long beep (low followed by high frequency) | Power is ON |
| Long beep (high followed by low frequency) | Power is OFF |
| Short beep (low frequency) | Indicates bar code is read, or pairing is |
successful
Short beep (high followed by low frequency)| Configuration setting success
Three short beeps (low frequency)| Wireless transmission failed
Two short beeps (low frequency)| Wireless connection disconnect
Two short beeps (high frequency)| Configuration setting failure
Button
| LED | Description |
|---|
Button
| Short press to power ON
Hold down the button for 8 seconds to enter Bluetooth HID pairing When pairing, double-click to end pairing
System Options
Connect Options
Other Device Settings
Dimensioning Units and Output
Suffixes and Prefixes
Batch and Online Modes
Workflow and Process Options
Disclaimer © 2023
ParcelTools Pty Ltd. All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or remove the seal label from the device, doing so will void the product warranty provided by ParcelTools. All pictures in this manual are for reference only and the actual product may differ. Regarding to the product modification and update, ParcelTools have the right to make changes to any software or hardware to improve reliability, function, or design at any time without notice. The information contained herein is subject to change without prior notice. The products depicted in this manual may include software copyrighted by ParcelTools or a third party. The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior written consent from the copyright holders. Specifications were correct at the time of printing.
References
- Ship Smart with Cubetape's Dimensional Weight Scanner
- Support - UPS Dimension & Weight Scanning Systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>