cubetape C200 Series Dimensional Weight Scanner User Guide

cubetape C200 Series Dimensional Weight Scanner

Product Information

The C200 Series is a measuring device that allows you to easily scan in dimensions of up to 2 inches (50mm) using a Cubetape ScanStik. The device comes with a USB cable, RF dongle, Bigfoot silicone tip, and a charging cradle (if selected). It has a red LED light that indicates when the battery is charging. The device can be powered on by pressing the Measure button.

Product Usage Instructions

1. To use the Cubetape ScanStik, first, peel the ScanStik and place it on an easily accessible reference edge, such as the side of the scale work base. The yellow arrows should point toward the reference edge.
2. Place the package to be measured with its back edge next to the reference edge and over the ScanStik.
3. Use the Cubetape to scan the barcode on the ScanStik closest to the package. It may be easiest to scan down the package until the scanner reads the barcode on the ScanStik.

For full product manual and support, visit www.cubetape.com/downloads or email support@cubetape.com.

Registration
To register your device, you can either scan the registration QR code or visit www.cubetape.com/register.

Charging Instructions
To charge the battery, insert the USB cable by the Measure button and connect it to an adaptor. If using a charging cradle, connect the USB cable and insert the C200. The red LED light will turn on when charging.

Default Settings and Factory Reset

The factory default settings for the device are units = inches, interval = nearest inch, suffix DIM = TAB, and suffix GEN = TAB. You can connect to a Windows host using the dongle. To return to factory settings at any time, scan “Restore Scanner Defaults” and “Restore Wireless Defaults”.

Note: There is repetition of information in the given text, which has been removed from the response for clarity.

Scan Registration QR code or visit www.cubetape.com/register to register your device

IN THE BOX

For full manual go to www.cubetape.com/downloads
For support email support@cubetape.com

CHARGE BATTERY: Insert USB cable by the Measure button and connect to adaptor or if using charging cradle, connect USB cable and insert C200. Red LED is ON when charging.
POWER ON C200: Press the Measure button to power on.
OPTION 1: Connect to Windows using RF dongle.

• Scan Pair, LED will flash green.

• Insert dongle in spare Windows USB port, LED will turn blue when connected.

• Dimensions and barcodes will now be sent to the active Windows app.
  OPTION 2: Connect to Android or Windows using Bluetooth Direct Mode (HID).

• Scan BT Direct (HID).

• Scan Pair or hold measure button for 6 seconds to enter pairing mode. LED will flash alternately blue and green. (To cancel pairing mode press Measure twice).

• Connect Cubetape from Android or Windows connection menu. LED will turn blue when connected.

• Dimensions and barcodes will now be sent to the active app.
  OPTION 3: Connect to 3rd Party Android or Windows app using Bluetooth Application Mode (SPP).

• Scan BT App (SPP).

• Refer to 3rd Party Application Guide.

DEFAULTS AND FACTORY RESET

Factory default settings are: Connect to Windows host using dongle

• Units = inches
• Suffix DIM = TAB
• Output = nearest inch
• Suffix GEN = TAB

Return to factory settings anytime by scanning Scanner Defaults and Wireless Defaults.

HOW TO MEASURE

1. Hook the tape end over the far edge of the package.
2. Align the tape exit point to the near edge of the package.
3. Press the ‘m’ button to record and transmit the measurement.

ASSEMBLY

1. The tape cassette has guide rails on both sides.
2. The C200 Pod has guide grooves on both sides.
3. Spring latch locks into the tape cassette.
4. Align grooves and rails.
5. C200 Pod slides down into the tape cassette.
6. The latch in the C200 Pod locks into the tape cassette.

SET UNITS AND OUTPUTS

Select preferred units – inches or cm and output.

SET SUFFIX

Select preferred suffix for use with Dimensional (DIM) and General (GEN) items.

References

• Support - CubeTape
• Warranty registration - Cubetape
• Support - UPS Dimension & Weight Scanning Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>