cubetape C200 Series Compact Dimensioning Device User Guide
- June 9, 2024
- cubetape
Table of Contents
C200 Series
Quick start Guide
Scan Registration QR code or visit
www.cubetape.com/register to register your
device
IN THE BOX
|
---|---
For full manual go to
www.cubetape.com/downloads
For support email support@cubetape.com
| | |
---|---|---|---
[www.cubetape.com/register](http://www.cubetape.com/register)|
^%%##^Code99|
^%%##^CodeAA|
^%%##^CodeAB CHARGE BATTERY: Insert USB cable by the Scan button and connect to
adaptor or if using charging cradle, connect USB cable and insert C200. Red
LED is ON when charging.
POWER ON C200: Press the Scan button to power on.
OPTION 1: Connect to Windows using RF dongle.
- Scan Pair, LED will flash green.
- Insert dongle in spare Windows USB port, LED will turn blue when connected.
- Dimensions and barcodes will now be sent to the active Windows app.
OPTION 2: Connect to Android or Windows using Bluetooth Direct Mode (HID).
-
Scan BT Direct (HID).
-
Scan Pair or hold Scan button for 6 seconds to enter pairing mode.
LED will flash alternately blue and green. (To cancel pairing mode press Scan twice). -
Connect Cubetape from Android or Windows connection menu.
LED will turn blue when connected. -
Dimensions and barcodes will now be sent to the active app.
OPTION 3: Connect to 3rd Party Android or Windows app using Bluetooth Application Mode (SPP).
- Scan BT App (SPP).
- Refer to 3rd Party Application Guide.
DEFAULTS AND FACTORY RESET
Factory default settings are:
Connect to Windows host using dongle
Units = inches
Suffix DIM = TAB
Output = nearest inch Suffix GEN = TAB
Return to factory settings anytime by scanning
Scanner Defaults and Wireless Defaults.
Charge Cradle also contains the Shortcuts QR Code on base.| |
---|---|---
https://cubetape.com/wp-content/uploads/2022/08/C200Series-Shortcuts.pdf
|
^#SC^303FFF1|
^%%##^Code93 HOW TO MEASURE
- Hook the tape end over the far edge of the package.
- Align the tape exit point to the near edge of the package.
- Press the Scan button to record and transmit the measurement.
ASSEMBLY
- The tape cassette has guide rails on both sides.
- The C200 Pod has guide grooves on both sides.
- Spring latch locks into the tape cassette.
- Align grooves and rails.
- C200 Pod slides down into the tape cassette.
- The latch in the C200 Pod locks into the tape cassette.
SET UNITS AND OUTPUTS
Select preferred units – inches or cm and output.
| |
---|---|---
^#SC^A0A0103|
^#SC^A0A0202|
^#SC^A0A0101 | |
^#SC^A0A0203|
^#SC^A0A0103|
SET SUFFIX
Select preferred suffix for use with
Dimensional (DIM) and General (GEN) items.
| | |
---|---|---|---
^#SC^A0A070D|
^#SC^A0A090D|
^#SC^A0A0709|
^#SC^A0A0909 FCC warning statements:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement.
IC warning statements:
Warning Statement:
RSS-GEN ISSUE 5, 8.4 User manual notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels of RF energy that are
deemed to comply without testing of specific absorption ratio (SAR).
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>