cybex PALLAS B i-SIZE 2 In 1 Car Seat User Guide

SILVER PALLAS B i-SIZE
UN R129/03, 76 cm – 150 cm ( > 15 m – ca. 12 y )
User guide

PALLAS B i-SIZE 2 In 1 Car Seat

https://go.cybex-online.com/pallas-b-isize-instructional-video

PALLAS B i-SIZE
i-Size Universal ISOFIX 76cm – 105cm / ≤ 21kg
Specific Vehicle Booster Seat 100cm – 150cm
030110
UN Regulation No. 129/03
Cybex GmbH Riedingerstr.  18, 95448 Bayreuth Germany

CERTIFICATION
UN R129/03
Age: > 15 months to approx. 12 years
Pallas B i-Size with impact shield: 76 cm – 105 cm, > 15 m, max. 21 kg
Pallas B i-Size with automatic three-point belt: 100 cm – 150 cm

Thank you for deciding on the Pallas B i-Size when choosing your car seat.
Carefully read this user guide before installing the car seat in your vehicle and always keep it to hand for future reference.

**** IMPORTANT INFORMATION AND WARNINGS

• Without the approval of the Type Approval Authority, the car seat may not be modified or added to in any way.

• In order to keep your child properly protected, it is absolutely essential that you use the car seat as described in this manual.

• Do not use before the child’s age exceeds 15 months and before it reached a size of 76 cm.

• This car seat may only be installed on vehicle seats which are approved for the use of child restraint systems according to the vehicle manual.

• Only suitable for vehicle seats with automatic three­point belts approved in accordance with UN Regulation No. 16 or a comparable standard.

• Do not use any load bearing contact points other than those described in the instructions and marked on the child restraint.

• The full surface of the backrest of the car seat must make contact with the backrest of the vehicle.

• When securing the child with impact shield (76 cm – 105 cm, > 15 m, max. 21 kg), the attachment of ISOFIX locking arms is not enough: it is absolutely necessary to attach the top tether belt in addition.

• The top tether belt may only be fastened to a marked attachment point.

• For usage in between height range 76 cm – 100 cm the impact shield must be used.

• The shoulder belt must run upwards and back at a recline. It must never run forward to the upper belt point in your vehicle.

• The vehicle belt buckle must never cross the arm rest of the seat. If the belt whip is too long, the car seat is not suitable for use in this position in the vehicle.

• The three­point belt must only be passed through the designated routings.
  The belt routings are described in detail in this manual and are marked in green on the car seat.

• The lap belt must run as low as possible across your child’s groin to have optimum effect in the event of an accident.

• Before each use make sure that the impact shield or automatic three­point vehicle belt is correctly adjusted and fits tightly to the child’s body. Never twist the belt!

• All straps must be tight and must not be twisted!

• Only an optimally adjusted headrest can offer your child maximum protection and comfort while ensuring that the shoulder belt can be fitted smoothly.

• The car seat must always be used with the backrest attached. The backrest may only be removed for cleaning or stowing.

• The car seat must always be secured correctly in the vehicle even when not in use.

• Always ensure that the car seat is not jammed when closing the car door or adjusting the back seat.

• Luggage or any other objects present in the vehicle must always be firmly secured. Otherwise, they may be thrown within the car, which could cause fatal injuries.

• The car seat must never be used without the seat cover. Ensure that only an original CYBEX seat cover is used, as the cover is a key element of the seat’s function.

• Never leave your child unattended in the car.

• The parts in the child restraint system heat up in the sun and could potentially burn your child’s skin. Protect your child and the car seat from direct sun exposure.

• An accident may cause damage to the car seat that is not identifiable with the naked eye. Please replace the seat after an accident. In case of doubt, please consult your dealer or the manufacturer.

• Do not use this car seat for more than 11 years. The car seat is exposed to high stress during its product life span, which leads to changes in the quality of the material with increasing age.

• The plastic parts can be cleaned with a mild cleaning agent and warm water.

• Never use harsh cleaning agents or bleaches!

• On some vehicle seats made of sensitive materials, the use of car seats may leave marks and/or cause discolouration. To prevent this, you can place a blanket or towel or similar underneath the car seat to protect the vehicle seat.

PRODUCT PARTS

(1) Backrest
(2) Booster
(3) Impact shield (76 cm – 105 cm)
(4) ISOFIX adjustment handle
(5) ISOFIX locking arms
(6) ISOFIX anchorage points
(7) ISOFIX safety indicator
(8) Top tether belt
(9) Top tether safety indicator
(10) ISOFIX release buttons
(11) Adjustable headrest| (12) Adjustment handle of headrest
(13) Belt of the impact shield
(14) Belt adjuster release button
(15) Belt adjuster
(16) Buckle of the impact shield
(17) Tongue of the impact shield
(18) Lap belt guide (100 cm – 150 cm)
(19) Shoulder belt guide (100 cm – 150 cm)
(20) Top tether adjustment button
(21) Belt release hook
(22) Metal bracket
---|---

INITIAL ASSEMBLY

Connect the backrest (1) to the booster (2) by hooking the guide lug on the axis of the booster. The backrest (1) is then folded forward. Place the impact shield (3) on the booster (2).

THE CORRECT POSITION IN THE VEHICLE

76 cm – 105 cm; > 15 m with impact shield
This is an i­Size Enhanced Child Restraint System. It is approved according to UN Regulation No. R129/03, for use in i­Size compatible vehicle seating positions as indicated by vehicle manufacturers in their vehicle user guides. If your vehicle does not have an i­Size seating position, please check the vehicle type list. You can obtain the most up­to­date version from go .cybex-online.com/pallas-b-isize-car-compatibility.
100 cm – 150 cm; with automatic three-point belt
The car seat can be used on vehicle seats which are equipped with an automatic three­point belt. Refer to the vehicle type list for approved vehicles.
You can obtain the most up­to­date version from go.cybex-online.com /pallasb-isize-car-compatibility.
For the use with three­point belt between the height range 100 cm – 150 cm
there is the possibility of usage without ISOFIX and top tether. In this case, the car seat must always be secured with the three­point belt even when there is no child in the seat.
In exceptional cases, the car seat may also be used on the front passenger seat. Always comply with the recommendations of the vehicle manufacturer.
? Above a child’s height of 135 cm, the compatibility between the car seat and your vehicle might be reduced.

INSTALLING THE CAR SEAT IN THE VEHICLE

1. Always ensure that…
   • the backrests in the vehicle are locked in their upright position.
   • when installing the car seat on the front passenger seat, adjust the vehicle seat as far back as possible without affecting the belt routing.

2. Pull the ISOFIX adjustment handle (4) and pull out the ISOFIX locking arm (5) with the other hand until it locks into position. Repeat the same for releasing the ISOFIX locking arm (5) on the other side.
   ? The ISOFIX locking arms have to be released independently.

3. Place the car seat on an appropriate seat in the car.

4. Push the ISOFIX locking arms (5) into the ISOFIX anchorage points (6) until these lock into place with an audible “CLICK”. The two ISOFIX safety indicators (7) will switch from red to green.

5. Ensure the car seat is secure by trying to pull it out of the ISOFIX anchorage points (6).

6. The car seat can be brought into different sitting or recline position by pressing the ISOFIX adjustment handle (4) and moving the car seat forward or push back. See chapter “ADJUSTING THE RECLINE POSITIONS”.
   ? If the headrest of the vehicle is in the way, pull it upwards to its furthest extent or remove it completely (except in rear­facing vehicle seats).

7. Guide the top tether belt (8) straight across the vehicle seat and anchor it using the snap hook on the anchor point of your vehicle.
   ? Top tether can be extended by pressing the top tether adjustment button (20).
   ? Pass the top tether belt underneath the car headrest. Never pass the top tether belt over the car headrest.

8. Tighten the top tether belt (8) until the top tether safety indicator (9) turns green.

REMOVAL FROM THE VEHICLE

Perform the installation steps in the reverse order.

1. Remove the top tether belt (8).
2. Unlock the ISOFIX locking arms (5) on both sides by pushing the ISOFIX release buttons (10) and pull them back.
3. Pull the car seat away from the ISOFIX anchorage points (6).
4. Remove the car seat. Then press the ISOFIX adjustment handle (4) and push the ISOFIX locking arms (5) back until you feel a slight resistance.
   Release the adjustment handle and push the ISOFIX locking arms (5) fully back into the transport position.

ADJUSTING THE RECLINE POSITIONS

This car seat offers 3 sitting positions.

1. To put the car seat in the desired recline position, press the ISOFIX adjustment handle (4) on the underside of the front area of the booster (2)and pull the car seat forward.
2. To return the car seat from the recline position to the sitting position, press the ISOFIX adjustment handle (4) again and guide the seat upwards with light pressure against the booster (2).

? The three indicator lines on the ISOFIX locking arms indicate the respective position.
? The car seat has to be adjusted to one of the sitting positions before the child is seated.

ADJUSTING THE HEADREST

The adjustable headrest (11) can be adjusted by using the adjustment handle (12) at the back of the headrest. Adjust the headrest so that max. 2 cm (approx. 2 finger’s width) remain between the child’s shoulder and the headrest.
? The height of the headrest can still be adjusted while the car seat is installed in the vehicle.

CORRECT INSTALLATION MODE

| 76 cm – 105 cm,
max. 21 kg, > 15 m| 100 cm – 150 cm
---|---|---
Installation mode| with impact shield| without impact shield
Installation| |

SECURING THE CHILD WITH IMPACT SHIELD: 76 CM – 105 CM (MAX. 21 KG, > 15 M)

1. Loosen the belt of the impact shield (13) by pressing the release button (14) on the belt adjuster (15).

2. Open the buckle of the impact shield (16) and lay the impact shield on its side.

3. Now place your child in the car seat.
   ? Make sure that the headrest is adjusted correctly.

4. Push the impact shield (3) back into the designated guide and insert the tongue of the impact shield (17) into the buckle of the impact shield (16) so that it engages with an audible “CLICK”.

5. Now pull on the belt of the impact shield (13) to adjust it and restrain your child correctly. Move the impact shield (3) a little bit by tilting it back and forward to achieve an optimal fit and position.

6. Adjust the impact shield (3) so that it fits snugly against the child’s body and pelvis and is positioned centrally in front of your child.
   ? The tightening of the belt must be repeated each time you buckle up.

7. Check whether the tongue of the impact shield (17) is properly engaged by pulling on the impact shield (3).

REMOVING AND REATTACHING THE IMPACT SHIELD

As soon as your child is taller than 105 cm or weighs more than 21 kg, the impact shield (3) must be removed.
To remove the impact shield (3) follow the next steps:

1. Open the buckle of the impact shield (16).
2. Press the belt adjuster release button (14) and undo the belt (13) as much as possible.
3. Remove the seat cover on the left side of the booster (2) until you can see the belt fixation point.
4. Press the belt release hook (21) on the fixation point and loosen the metal bracket (22).
5. Turn the metal bracket (22) so that it can pass through the opening of the fixation point.
6. Pull the belt of the impact shield (13) completely through the tunnel of the armrest and through the hole in the seat cover.
   ? Note that using the seat without an impact shield is not permitted before your child reaches a height of at least 100 cm.
   ? Keep the impact shield in a safe and secure place.

To reattach the impact shield (3) to the booster (2), follow the steps described above in reverse order.
Make sure the metal bracket (22) is firmly in place and locked behind the belt release hook (21).
? Make sure that the arrow on the metal bracket and the arrow on the fixation point point to each other.

SECURING THE CHILD WITHOUT IMPACT SHIELD: 100 CM – 150 CM

1. Route the lap belt of the vehicle seat around your child through the green marked lap belt guides (18) and insert the belt tongue into the belt buckle of the vehicle. It must lock into place with an audible “CLICK”.
2. Tighten the lap belt by pulling on the shoulder belt before inserting the shoulder belt into the belt guide.
3. Insert the shoulder belt and the lap belt together into the lap belt guide (18) on the side of the vehicle belt buckle.
4. Feed the shoulder belt through the green shoulder belt guide (19) until it is inside of it.
5. Tighten the shoulder belt by pulling on it.
6. Ensure that the shoulder belt runs across your child’s clavicle and does not touch your child’s neck. If necessary, adjust the height of the adjustable headrest (11) to change the position of the belt.

REMOVING AND REATTACHING THE SEAT COVER

The cover of the car seat consists of four parts (headrest, backrest, booster and impact shield). These are held in position at several places by press studs and elastic bands. Once all attachments have been released, the single parts of the cover can be removed. To remove the booster (2) cover, the impact shield (3) must be taken off. To do this, please follow the steps in the chapter “REMOVING AND REATTACHING THE IMPACT SHIELD”.
In order to put the covers back on the seat, proceed in reverse order.
? The cover may only be washed at 30 °C with a delicate wash program otherwise it may result in discoloration of the cover fabric. Please wash the cover separately from other laundry and do not dry in the dryer or in direct sunlight!

MANUFACTURER’S WARRANTY AND DISPOSAL REGULATIONS

CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you 3 years warranty on this product. The warranty is valid in the country, where this product was initially sold by a retailer to a customer. The contents of the warranty and all essential information required for the assertion of the warranty can be found on our homepage go.cybex-online.com/manufacturer- warranty-car-seats. If a warranty is shown in the article description, your legal rights against us for defects remain unaffected.
Please observe the waste disposal regulations in your country.

REVISION INDEX

CYBEX GmbH
Riedingerstr. 18 | 95448 Bayreuth | Germany
www.cybex-online.com
C Y_172_0371_B1123

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>