cybex R129-03 Cloud T i Size Seat 45-87 cm User Guide

cybex R129-03 Cloud T i Size Seat 45-87 cm

Product Information

• Specifications:
  • Brand: CYBEX GmbH
  • Model: CLOUD T i-SIZE
  • Size Range: R129/03, 45-87 cm
  • Weight Limit: Maximum 13 kg

Product Usage Instructions

• Installation in the Vehicle:
  • Slide the ISOFIX connectors out of the base of the car seat.
  • Place the base on the appropriate vehicle seat.
  • Insert the ISOFIX connectors into the vehicle’s ISOFIX anchorage points.
  • Ensure the base is securely attached to the vehicle seat.
• Attaching the Child Seat:
  • Position the child’s seat on the base.
  • Lock the child seat onto the base in the desired position.
  • Make sure the child seat is properly aligned with the vehicle floor.
• Removing the Child Seat:
  • Pull up the seat release handle to unlock the child seat.
  • Tilt the child seat slightly and lift it off the base.
  • Unlock the ISOFIX connectors on both sides to remove the child seat completely.
• Child Safety:
  • Ensure the harness is securely tightened around the child, with no folds in the straps. When using Sensor Safe, position the clip below the shoulder pads.
• Sun Canopy Adjustment:
  • To adjust the sun canopy, simply pull on the plastic cover to extend it.

FAQs

• Q: Can I use this car seat without the base?
  • A: Yes, you can use the car seat without the base on a forward-facing vehicle seat equipped with an automatic three-point seat belt complying with UN R16 standards.
• Q: How should I clean the car seat?
  • A: The car seat can be cleaned with water. Avoid using harsh cleaning agents or bleach.

OVERVIEW

GO TO CYBEX-ONLINE.COM TO WATCH AN INSTRUCTIONAL VIDEO

CERTIFICATION

• CLOUD T i-Size
• Size range: 45–87 cm
• Weight: max. 13 kg

Thank you for deciding on the CLOUD T i-Size when choosing your car seat. Carefully read this User guide before installing the car seat in your vehicle and always keep it to hand in the designated compartment (34).

IMPORTANT INFORMATION AND WARNINGS

• Without the approval of the Type Approval Authority, the car seat may not be modified or added to in any way.
• To keep your child properly protected, you must use the car seat as described in this User guide.
• This car seat may only be installed on vehicle seats that are approved for the use of child restraint systems according to the vehicle manual.
• The car seat can either be attached with the Base T/Base Z2 and ISOFIX, or with a 3-point automatic belt that is approved according to UN regulation No. 16 or an equivalent standard.
• If the car seat is installed using a 3-point automatic belt, the vehicle belt buckle must never reach the lap belt guide of the car seat. If the belt whip is too long, the car seat is not suitable for use in this position in the vehicle.
• The installation of this car seat on the front passenger seat with the front airbag activated is NOT PERMITTED.
• Do not use any load-bearing contact points other than those described in the User Guide and marked on the child restraint.
• The Newborn inlay is used to protect your child and must be used up until they have reached a height of 60 cm.
• Before each journey make sure that the car seat harness system is correctly adjusted and fits tightly to the child’s body. The belts must never be twisted!
• Always buckle up your child when it is in the car seat.
• Only an optimally adjusted headrest can offer your child maximum protection and comfort while ensuring that the belt system can be fitted appropriately.
• The car seat must always be correctly installed and secured in the vehicle even when not in use.
• If the car seat is used with the Base T/Base Z2 the load leg must always make direct contact with the floor of the vehicle. If your vehicle has storage compartments in the footwell, be sure to contact the vehicle manufacturer.
• While driving, the car seat must always be locked in the rear-facing position.
• For the car seat to provide the best possible protection, always use linear side-impact protection (L.S.P.).
• If using the car seat on the middle seat of the vehicle, the linear side-impact protection (L.S.P.) must never be folded out.
• The car seat has also been tested and approved for use without the linear side-impact protection (L.S.P.) folded out.
• Always ensure that the car seat is not jammed against any surface when closing the vehicle door or adjusting the back seat.
• Luggage or any other objects present in the vehicle must always be firmly secured. Otherwise, they may be thrown within the vehicle, which could cause fatal injuries.
• The car seat must never be used without the seat cover. Ensure that only an original CYBEX seat cover is used, as the cover is a key element allowing the seat to function correctly.
• Never leave your child unattended in the vehicle.
• It is allowed to use the intermediate lie-flat position in the car if the seat is used with Base T/Base Z2. If the car seat is installed using a 3-point automatic belt, it has to be in the most upright position.
• The full lie-flat position may only be used outside the vehicle.
• Do not place the car seats on raised surfaces, such as a table.
• Parts of this child restraint system can heat up when exposed to direct sunlight and could potentially burn your child’s skin. Protect your child and the car seat from direct sun exposure.
• An accident may cause damage to the car seat that is not identifiable to the naked eye. Please replace the car seat after an accident. In case of doubt, please consult your dealer or the manufacturer.
• Do not use this car seat for more than 8 years. The car seat is exposed to high stress during its product lifespan, which leads to changes in the quality of its materials with increasing age.
• The plastic parts can be cleaned with a mild cleaning agent and warm water. Never use harsh cleaning agents or bleaches!
• On some vehicle seats made of sensitive materials, the use of car seats may leave marks and/or cause discolouration. To prevent this, you can place a blanket, towel or similar underneath the car seat to protect the vehicle seat.

PRODUCT PARTS

• Battery compartment (1)
• Base (2)
• Load leg (3)
• Newborn inlay (4)
• ISOFIX-Release buttons (5)
• ISOFIX-Locking arms (6)
• ISOFIX-Anchorage points (7)
• ISOFIX-Indicators (8)
• Load leg adjustment button (9)
• Load leg indicator (10)
• Carrying handle (11)
• Carrying handle release buttons (12)
• Seat locking indicator (13)
• Linear side-impact protection
• (L.S.P.) (14)
• Tilt angle indicator (15)
• 3-point automatic belt (16)
• Lap belt guide (17)
• Diagonal belt guide (18)
• Seat release handle (19)
• Load leg parking position (20)
• Headrest (21)
• Headrest adjustment handle (22)
• Belt adjustment button (23)
• Shoulder belt (24)
• Belt buckle (25)
• Buckle tongue (26)
• Central adjustment belt (27)
• Seat rotation handle (28)
• Driving direction indicator (29)
• Driving Direction Control (D.D.C.) (30)
• Sun canopy (31)
• Release handle for lie-flat position (32)
• Release button for stroller adapter (33)
• User guide compartment (34)

THE CORRECT POSITION IN THE VEHICLE

• This is an i-Size Enhanced Child Restraint System. It is approved according to UN Regulation No. R129/03, for use in i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in their vehicle user manuals.
• If your vehicle does not have an i-Size seating position, please check the vehicle Type List.
• You can obtain the most up-to-date version of the Type List from www.cybex-online.com.
• Alternatively, the car seat may be installed on forward-facing vehicle seats equipped with a 3-point automatic belt system.
• It is not guaranteed that all sitting and reclining positions can be used in all approved vehicles.

DIFFERENT USES OF THE SEAT

• The Newborn inlay (4) integrated at purchase should be removed if your child is taller than 60 cm.
• To remove the Newborn inlay (4) open the belt buckle (25), pull off the shoulder pads and then remove the inlay.

PREPARING TO INSTALL THE BASE T/BASE Z2

• Before using the base for the first time, the plastic strip must be removed from the Battery compartment (1) on the Load leg (3).
• The Base (2) will emit an audible warning signal until it has been correctly installed.
• If the Load leg (3) is folded out and there is no sound, the battery must be checked.
• To check the battery, the Battery compartment (1) on the back of the load leg can be opened with a screwdriver.
• The battery may only be replaced with a CR2032-size battery.

INSTALLATION IN THE VEHICLE

Always ensure that…

• the backrests in the vehicle are locked in their upright position.
• when installing the car seat on the front passenger seat, adjust the vehicle seat as far back as possible.
• The infant car seat is exclusively made for forward-facing car seats, which are equipped with ISOFIX or a 3-point belt system.

Installation of the car seat with Base T/Base Z2

1. Keep the Driving Direction Control (D.D.C.) button (30) downward and ensure the base is adjusted for rearward-facing car seats.
2. Fold out the Load leg (3) until it locks into its foremost position. An acoustic warning signal will sound until the load leg has been correctly installed.
3. Release the ISOFIX-Release buttons (5) to extend the ISOFIX-Locking arms (6).
   • The ISOFIX-Release buttons can both be released independently allowing the ISOFIX-Locking arms to be adjusted independently.
4. Push the ISOFIX-Locking arms (6) out of the Base T/Base Z2o to their furthest extent.
5. Place the base (2) on an appropriate seat in the vehicle.
6. Push the ISOFIX-Locking arms (6) into the ISOFIX-Anchorage points (7) until these lock into place with an audible “CLICK”. The two ISOFIX indicators (8)will switch from RED to GREEN.
7. Ensure the base is secure by trying to pull it out of the ISOFIX-Anchorage points (7).
8. Push the Base (2) towards the backrest of the vehicle seat until it is fully aligned with the backrest.
   • ? Moving the base from side to side will also brace it against the vehicle backrest.
9. Press the Load leg adjustment button (9) and extend the leg until it touches the vehicle floor.
10. Pull the Load leg (3) out to the next locking position to ensure optimal force transmission.
11. The Load leg indicator (10) switches to GREEN when the load leg is correctly positioned on the vehicle floor and the acoustic warning signal stops.
12. Move the Carrying handle (11) to position A. Therefore, press the two Carrying Handle release buttons (12) on the left and right of the Carrying handle at the same time.
13. Place the car seat on the Base (2).
14. The car seat can also be locked in its entry position on the base. Then turn the car seat until it is aligned opposite to the direction of travel.
15. Please ensure that the car seat locks into place with an audible “CLICK”.
16. Check whether the Seat locking indicator (13) on the base is GREEN.
17. To achieve the best possible protection, activate the Linear side impact protection (L.S.P) (14) on the side of the car seat facing the vehicle door by pulling on its end.
    • ? The car seat can also be used with the L.S.P. folded in if there is not enough space in the vehicle. To do this, fold in the element back to its starting position.

Installing the car seat with a 3-point automatic belt

1. Place the car seat on the vehicle seat against the direction of travel.
2. Make sure that the Carrying handle (11) is locked in position A.
3. Make sure that the Tilt indicator (15) is parallel with the vehicle floor.
4. Pull out the 3-point automatic belt (16) and place its lap section into the lap belt guide (17).
5. Lock the 3-point automatic belt (16) of the vehicle in its belt buckle.
6. Tighten the lap section by pulling the diagonal section in the direction of travel.
7. Guide the diagonal section of the belt behind the head end of the car seat and through the diagonal belt guide (18) and above the Linear side-impact protection (L.S.P) (14).
8. To achieve the best possible protection, activate the Linear side impact protection (L.S.P) (14) on the side of the car seat facing the vehicle door by pulling on its end.
   • ? The car seat can also be used with the L.S.P. folded in if there is not enough space in the vehicle. To do this, fold in the element back to its starting position.

REMOVAL FROM THE VEHICLE

Removal of the car seat with Base T/Base Z2

1. To unlock the car seat from the base (2), pull the Seat release handle (19) up.
2. Tilt the car seat slightly and lift it off the base (2).
3. Unlock the ISOFIX-Locking arms (6) on both sides by pressing the ISOFIXRelease buttons (5) and at the same time pulling them back.
4. Pull out the Base (2) from the ISOFIX-Anchorage points (7).
5. Remove the Base (2) and slide the ISOFIX-Locking arms (6) completely back into their transport positions.
6. Push the Load leg (3) back into its original position and then fold it in to save space.
7. It is important to fully fold in the load leg so that the acoustic warning is muted. There is a Load leg parking position (20) indicated on the underside of the base.

Removal of the car seat with a 3-point automatic belt

1. Take the diagonal section of the belt out of the diagonal belt guide (18).
2. Unlock the vehicle seat belt buckle and take the lap section of the belt out from the lap belt guides (17).

ADJUSTING THE HEADREST

The adjustable Headrest (21) can be adjusted by using the Headrest adjustment handle (22). When adjusting the Headrest (21) ensure that no more than 2 cm (approx. 2 finger’s width) remain between the child’s shoulders and the headrest.

SECURING THE CHILD

1. Press the Belt adjustment button (23) and pull both Shoulder belts (24) at the same time to loosen them.
2. Undo the Belt buckle (25) by pressing the red button firmly.
3. Put your child in the car seat with their buttocks at the back.
4. Place the Shoulder belts (24) directly over your child’s shoulders.
5. Place both Buckle tongues (26) together and lock them in place in the Belt buckle (25). You should hear an audible “CLICK”.
6. If you are using a seat with a SensorSafe Clip, push the clip closed until you hear an audible “CLICK” and slide the closed clip down towards the Belt buckle (25).
7. Pull on the Central adjustment belt (27) to tighten the Shoulder belts (24) until they rest snugly against your child’s body.
   • ? The harness should be fitted tight enough so that it is not possible to put a fold in any of the straps.
8. When using the SensorSafe clip, position the clip directly below the shoulder pads.

ROTATION FUNCTION BASE T/BASE Z2

• Pull the Seat rotation handle (28) on the Base T/Base Z2o and turn the car seat.
• Before starting your journey, make sure that the car seat is properly locked into place and the Driving direction indicator (29) shows GREEN.

ADJUSTING THE SUN CANOPY

• Unfold the Sun canopy (31) by pulling on the plastic cover.

ADJUSTING THE LIE-FLAT POSITIONS

• The car seat can be switched between the lie-flat positions by pressing the release handle for the lie-flat position (32) while simultaneously shifting the back section downwards.
  • ? The car seat can be put into two lie-flat positions: the intermediate lie-flat position is also available inside the car if the car seat is used in combination with Base T/Base Z2. The full lie-flat position is only available outside the vehicle.

TRAVEL SYSTEM

• You can attach the car seat to any approved stroller. Click the car seat onto the approved adapter, facing the parent. To unlock, hold down the two Release buttons for the stroller adapter (33) and lift it up.

REMOVING AND REATTACHING THE SEAT COVER

• The car seat cover consists of 6 parts. These are fastened to the car seat at several places. Once unfastened, the individual parts of the cover can be removed.
• To reattach the cover, follow the removal instructions in the reverse order.
• ? The cover may only be washed at 30°C with a delicate wash program otherwise it may result in discolouration of the cover fabric. Please wash the cover separately from other laundry and do not dry it in the dryer or in direct sunlight!

MANUFACTURER’S WARRANTY AND DISPOSAL REGULATION

• CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you 3 years warranty on this product. The warranty is valid in the country where this product was initially sold by a retailer to a customer.
• The contents of the warranty and all essential information required for the assertion of the warranty can be found on our homepage: go.cybex-online.com/manufacturer-warranty-car-seats.
• If a warranty is shown in the article description, your legal rights against us for defects remain unaffected.
• Please observe the waste disposal regulations in your country.
• CLOUD T i-SIZE R129/03, 45-87 cm, max. 13 kg

References

• CYBEX Online Shop | Child Car Seats, Strollers, Baby Carriers and Furniture from CYBEX
• CYBEX Online Shop | Child Car Seats, Strollers, Baby Carriers and Furniture from CYBEX
• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>