700500 Artis Svelto LED Black Mirror Cabinet Instruction Manual
- March 10, 2024
- artis
Table of Contents
700500 Artis Svelto LED Black Mirror Cabinet
Wall Mounted Mirror Cabinet
- Adjustable stainless steel buffer hinge
- Double layer adjustable tempered glass shelf
- Touch sensor switch
- Aluminum alloy cabinet
- Double-sided copper-free silver mirror
Note: This specification applies to Single door touch sensor switch LED Aluminum Cabinets.
Packing List
-
Expansion plug Ø8
-
Screw M5
-
L shape fixing
-
Aluminum alloy bar
-
Glass shelf clip
-
Screw M4
Required tools
-
Tape measure
-
Spirit level
-
Electric drill
-
Screwdriver
-
Hammer
-
Drill bit
-
Pencil
Note: Please carefully read the following before installing
Warning
- Before installing the product, please carefully read the instructions and operate accordingly;
- Before installing, please turn off the main power switch and ensure that it won’t turn on;
- All electrical products should be fitted by a suitably qualified electrician in accordance with wiring regulations(BS7671)
- This mirror cabinet is heavy; do not lift or install with single person in order to avoid injury;
- Before installing, please check whether the product is broken, to avoid injury caused by damaged glass;
- Do not clean the product surface with acid and alkaline cleaning agent; please use a damp cloth.
The use of a spirit level
Non-standard level
standard level
- Look at the bubbles in the glass tube in the middle of the spirit level. The bubbles stay in the middle of the two black lines. It’s horizontal.
- Draw a straight line under the spirit level .
- Place the Aluminum alloy bar on the drawn line, line up the hole position and punch the hole.
Installation Steps:
-
Fixing the bar
-
Open the product packaging, and check whether the product has any exception or functional damage; if yes, please return it to the dealer.
-
After selecting the location of the mirror cabinet, check whether the wall is solid, measure the distance of the holes (A, A-1) in the aluminum alloy bar with a tape measure and mark it on the wall with a pencil (Fig. 1 ).
-
Drill holes in the marked position with electric drill and 08 drill bit, and use special ceramic drill if the wall surface is ceramic tile.
-
Knock the expansion plugs into the holes in the wall with a hammer, and then tighten the screws with a screwdriver to fix the bar, and calibrate the level with a spirit level (Fig. 2).
-
Positioning and Installation of Mirror Cabinet:
-
Using a screw to tighten the L shape fixing on the bottom of the cabinet (Fig.3).
Attach the mirror cabinet to the bar as shown in Fig. 3, open the cabinet door, and mark on the wall with a pencil (Fig. 4) through the backplane hole (a). -
Remove the mirror cabinet, drill the fixing hole in the wall in the marked position, and place the expansion plugs (Fig. 5).
-
Repeat the operation as shown in Fig. 3 and mount the mirror cabinet to the bar, make sure that the circuit on the wall is not energized and connect the three-core wire reserved on the wall to the three-core wire terminal block on the product (Fig. 6), and then tighten the screws on the backplane(Fig.6-b).
-
place the clips in the left and right side of the cabinet carcass(Fig. 7).
-
put the glass shelf on the one of the clip, and push gently the glass shelf on the other clip(as arrow)(Fig.8).
-
Finally, switch on the power, and then touch the switch sign (Fig.9) with a finger on the lens to test the products.
-
Mirror Door Adjustment
-
Fix the mirror cabinet, and check if the mirror door is flat; if not (as shown in Fig.1 O),adjust the distance of the door opening by adjusting the hinge screw (b) and keep the door level (Fig.11).
-
If the cabinet door isn’t flat ( Fig.12 ), adjust the distance between the door and the cabinet by adjusting the screw (c) to make the door flat. (Fig.13)
Warning: The distance between the door and the cabinet should not be too small, otherwise the door can’t be opened and may lead to the door rupture.
Safety Warning
- Do not disassemble the door unless necessary