FRIGIDAIRE FHWW085WE1 8000 BTU Inverter Window Room Air Conditioner Installation Guide

FRIGIDAIRE FHWW085WE1 8000 BTU Inverter Window Room Air Conditioner

Specifications

• BTU Range: 8,000-10,000
• Window Type: Double hung windows
• Window Opening Width: 24 to 36 inches (610 mm to 914 mm)
• Required Clearance: At least 11.8 inches (300mm) around the unit

Installation Instructions

Installation Warnings and Caution
Save the carton and installation instructions for future reference. Only use the specified screws for installation. The top rail must be securely fastened with all four screws for safety.

Top Rail Assembly

1. Remove the air conditioner from the carton and place it on a flat surface.
2. Remove the top rail from the packaging material.
3. Align the holes in the top rail with those on the top of the unit.
4. Secure the top rail to the unit using the provided 3/8 screws.

Filler Panel Assembly:

1. Place the unit on a flat surface.
2. Use the correct Left and Right side Filler Panels.
3. Slide the T section of the panel into the cabinet, ensuring it fits securely.
4. Adjust the panel to sit securely inside the frame channel and slide the top and bottom ends into the rails on the cabinet.
5. Repeat on the other side.

Window Installation
Your air conditioner is designed to install in standard double hung windows with specific opening dimensions. Ensure proper clearance around the unit as per guidelines.

Frequently Asked Questions (FAQ)
Q: Can I use any screws for installation?
A: No, only use the screws specified in the installation instructions for safety reasons.

Installation Instructions

READ BEFORE INSTALLING UNIT
WD Window Mounting (8,000-10,000 BTU)

INSTALLATION WARNINGS AND CAUTION

• The unit is for window mounting only.
• Carefully read the installation manual before beginning.
• Follow each step as shown.
• Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:

• Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp
• metal fins of front and rear coils. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
• Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended period of time.
• Handle air conditioner with care.
• Make sure air conditioner does not fall during installation.

NOTE

• SAVE CARTON and these INSTALLATION INSTRUCTIONS for future reference. The carton is the best way to store unit during winter, or when not in use.
• DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE.
• FOR SAFETY REASONS, THE TOP RAIL MUST BE SECURELY FASTENED WITH ALL FOUR (4) SCREWS.

Some assembly is required. Please read these instructions carefully.

Before installing, the top rail must be assembled on the unit.

• A. Remove the air conditioner from the carton and place on a flat surface.
• B. Remove top rail from the rear of the packaging material as shown in Fig. A
• C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
• D. Secure the top rail to the unit with the 3/8″ Screws as shown in Fig. C

How to InstallInstallation

LEFT + RIGHT FILLER PANEL ASSEMBLY
NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained!

1. Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels – be sure to use the proper panel for each side. When installed, the flange for securing the panel in place to the window sill will be facing into the room.

   • Hold the side Panel in one hand and gently pull back the center to free the open end. See FIG. 1.
   • Slide the free end “T” section of the panel directly into the cabinet as shown in FIG. 2. Slide the panel down. Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.
   • Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. See FIG. 3.
   • Slide the panel all the way in and repeat on the other side.
     Your air conditioner is designed to install in standard double hung windows with opening widths of 24 to 36 inches (610 mm to 914 mm) (FIG. 4A, FIG. 4B).
     Lower sash must open sufficiently to allow a clear vertical opening of 14 inches (356 mm ).
     Side louvers and the rear of the air conditioner must have clear air space to allow enough airflow through the condenser, for heat removal. The rear of the unit must be outdoors, not inside a building or garage. There should be at least 11.8 inches (300mm) clearance around the unit. See FIG. 4C & FIG. 4D.
     

2. Storm Window
   If the air conditoner is blocked by Storm Window, add wood as shown in FIG. 5, or remove storm window before air conditioner is installed.
   If Storm Window Frame must remain, be sure the drain holes or slots are not caulked or painted shut. Accumulated Rain Water or Condensation must be allowed to drain out.

3. Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit.
   

4. Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad windows).
   

5. Place the frame lock between the frame extensions and the window sill as shown (FIG. 8A for wooden windows), (FIG. 8B for Vinyl-Clad windows).

6. Drive locking screws:

   • A: For wooden windows:
     Drive 1/2″ (12.7 mm) locking screws through the frame lock and into the sill (FIG. 9A). NOTE:To prevent window sill from splitting, drill 1/8″ (3mm) pilot holes before driving screws. Drive 1/2″ (12.7 mm) locking screws through frame holes into window sash (FIG. 9B).

   • B: For Vinyl-Clad windows:
     Drive 1/2″ (12.7 mm) locking screws through the frame lock and into the window sash (FIG. 9B). NOTE: Before driving the screws, use a drill to drill 5 holes through the holes in the frame lock and frame extensions into the windows sash as shown ( FIG. 9B).

7. (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself.

8.  Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11).
   

9. Check that air conditioner is tilted back about 1/4″ to 1/2″ (tilted about 2º to 4° downward to the outside, see FIG. 12A & FIG. 12B). After proper installation, condensate should not drain from the overflow drain hole durin. normal use, correct the slope otherwise.

10. In order to minimize air leaks between the room air conditioner and the window opening, suitable weather stripping(trim the provided weather stripping into suitable size) should be applied in case of any gaps found at the location as indicated by the arrows in Fig. 13.
    

Removing the air conditioner From Window

• Turn the air conditioner off, and disconnect power cord.
• Remove sash seal from between windows, and unscrew sash lock.
• Remove screws installed through frame and framelock.
• Close (slide) side panels into frame.
• Keeping a firm grip on air conditioner, raise sash and carefully remove.
• Be careful not to spill any condensate water while lifting unit from window. Store parts WITH air conditioner.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>