JOY MGD-01R Sit and Stand Desk User Manual

May 15, 2024
JOY

JOY MGD-01R Sit and Stand Desk

JOY-MGD-01R-Sit-and-Stand-Desk-PRODUCT

Product Information

Specifications

  • Power Input: 100V-240V
  • Speed: 20 mm/s
  • Motion Noise: 55dB
  • Load Capability: 154 lbs / 70 kg

Component List

  • Top Panel (x1)
  • Back Panel (x1)
  • Middle Panel (x3)
  • Roller Shutters (x2)
  • Tabletop 1 (x1)
  • Tabletop 2 (x1)
  • Crossbar (x1)
  • Side Plate (x2)
  • Left Table Leg (x1)
  • Right Table Leg (x1)
  • Transmission rod (x1)
  • Leg Base (x2)
  • Controller (x1)
  • Power (x1)

Hardware List

  • Allen Key S=2mm (x1)
  • Allen Key S=5mm (x1)
  • Cam Lock (x5)
  • Cam Bolt (x5)
  • Wood Tip (x22)
  • Cable Clip (x2) Spare Parts
  • Rubber Pad (x10)
  • Headphone Hanger (x2)

Product Usage Instructions

Step 1 – Assembly

Follow the provided assembly instructions to assemble all the components using the hardware listed.

Step 2 – Installation

  1. Secure the components using the provided Allen keys and Cam Locks.
  2. Attach the Rubber Pads and Wood Tips as instructed.

Step 3 – Additional Installation Steps

Follow the remaining installation steps to complete the setup.

Using the Controller

  • To save height settings, short-press the corresponding button.
  • To adjust the desk height, use the buttons accordingly.
  • To change display settings, follow the provided instructions.

Protection Mode Error Codes

  • E10: Overheating Protection – Wait for at least 15 minutes before further adjustments.
  • E20: Sensor Malfunction Warning – Check connections and power back on.
  • E02, E32, E31: Overloading Warning – Adjust load and try again.
  • E60: Operation Status Warning – Follow reset instructions if needed.

Frequently Asked Questions (FAQ):

Q: What should I do if the desk stops moving during operation?

  • A: If the desk stops due to vibration, impact, or incline detection, follow the reset instructions before continuing use.

Q: How do I adjust the height settings using the controller?

  • A: Short-press the button to save the current height settings or press the corresponding button to move the desk to a preset height.

COMPONENT LIST

JOY-MGD-01R-Sit-and-Stand-Desk-FIG-1

HARDWARE LIST

INSTALLATION

JOY-MGD-01R-Sit-and-Stand-Desk-FIG-4 JOY-MGD-
01R-Sit-and-Stand-Desk-FIG-5 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-6 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-7 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-8 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-9 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-10 JOY-MGD-01R-Sit-and-Stand-Desk-
FIG-11

Using the Controller

S| Short-press the button S, and the display will flash. Press the 1 2 or 3 buttons to save the current height setting to that button.
---|---
1| Press the button, and the desk will move to the height that was previously set for that button.
2| Press the button, and the desk will move to the height that was previously set for that button.
3| Press the button, and the desk will move to the height that was previously set for that button.
| Press the button to raise the desk continuously until it reaches the highest position of 46.5″ (118cm) or the button is released.
| Press the button to lower the desk continuously until it reaches the lowest position of 28.3” (72cm) or the button is released.

JOY-MGD-01R-Sit-and-Stand-Desk-FIG-14

Protection Mode Error Codes

Hot| Overheating Protection: When the motor has been working continuously for 5 minutes, it will stop operating to prevent damage from overheating. Wait for at least 15 minutes before making any further height adjustments.
E10| Sensor Malfunction Warning: The motor safety sensor can’t be detected. Power off, check the connection between the motor and controller, and power back on again.
E20| Overloading Warning: Max load exceeded. If raising the desk, take the things off the desk and try again. If lowering the desk, power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline is detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, power off the desk, check the connection between power and the controller, and power on again.
E60| Unequal Leg Height Warning: Power off the desk and check whether the left and right legs are at the same height. Adjust if necessary by following the instructions. Power on again.
–| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals