LapLok 210314 Universal Anti Theft Laptop Lock Instruction Manual
- September 28, 2024
- LapLok
Table of Contents
210314 Universal Anti Theft Laptop Lock
“`html
Product Information
Specifications:
- Retrofitting laptop and tablet security product
- Secures devices to any table or flat surface
- Portable and convenient
- Includes loud alarm feature
Product Usage Instructions
Step 1: Register Your Lock/Unlock Code
-
Visit https://reset.LapLok.com/ or scan the QR code to go to
the registration page. -
Enter your name, email address, phone number, and the 5-Digit
Device Serial Number located at the bottom of your LapLok. -
A 4-Digit Verification Code will be sent to your phone number
and email. -
Input the 4-Digit Verification Code on the LapLok website’s
registration page. -
Choose and enter a 3-5 Digit Lock/Unlock Code as
instructed. -
Write your Lock/Unlock Code inside the lever for
safekeeping.
Step 2: Battery Activation
-
The batteries are pre-installed. Unlock and raise the Top to
locate and activate the switch underneath by turning it to the ‘ON’
position. -
Close the LapLok by releasing the Locking Pins into the Bolt
Catch. -
To test if the Batteries are working, press the Lock Button
once. Two blinks of the RED LED indicate battery activation. -
Under normal use conditions, Batteries last about 5 years. To
replace them in the future, refer to the ‘Replacing the Batteries’
section.
Step 3: Attach Mounting Plate, Arm, Parking Tab, and Laptop
Rubber Feet
-
Select a suitable spot on the laptop bottom for attaching the
Mounting Plate. Ensure it lies flat and does not obstruct any
features. -
Attach the Mounting Plate and Arm securely for easy rotation
and attachment to LapLok.
FAQ
Q: How long does the battery last?
A: Under normal use conditions, batteries should last about 5
years. If replacement is needed, refer to the user manual for
instructions.
Q: Can LapLok be used on all types of tables?
A: LapLok can secure your laptop or tablet to most tables or
flat surfaces. Ensure the surface is sturdy enough to support the
weight of your device.
“`
Thank you for purchasing LapLok, the world’s first convenient, retrofitting laptop and tablet security product, designed for the work-from-anywhere world. LapLok secures your laptop or tablet to any table or flat surface. It’s portable, convenient, and secure, with a loud alarm to drive away potential thieves.
CONTENTS
1 piece LapLok 1 piece Alcohol Wipe 1 piece Protective Bag 1 piece Primer
Ampule 2 pieces 2032 Batteries (installed) 1 piece Arm Mount
1 piece Parking Tab 4 pieces Laptop Rubber Feet 1 piece Carabiner 1 piece LapLok Warning Sticker 1 Adhesive with nozzle
OVERVIEW
HELP AND SUPPORT
Need help? Contact LapLok’s customer service line at 1-855 – 5LAPLOK (1 855
552-7565) or TechnicalSupport@LapLok.com Enjoying your LapLok? Share photos of
yourself using LapLok on social media and tag us!
OTHER MAINTENANCE TIPS
· Put your LapLok in its Protective Bag when not in use.
· Do not expose your LapLok to water or extreme temperatures.
· Do not leave your LapLok unattended for extended periods of time. Although
the LapLok is extremely secure, all anti-theft devices can eventually be
compromised with enough time.
· Care for your LapLok like you would other valuable electronics. It is good
to periodically clean the rubber pads and/or do not use LapLok on extremely
dirty surfaces
· When deciding on your Lock/Unlock Code, choose a 3-5 digit number that is
easy for you to remember and store it somewhere you won’t forget, such as your
laptop, phone and/or the inside of the lever.
· Change your Lock/Unlock Code every so often for better security hygiene.
SAFETY PRECAUTIONS
· Before attaching LapLok, ensure that the table surface is suitable for a
laptop. We do not recommend using LapLok on table linens as the grip is not
sufficient.
· Position LapLok on the table edge, ensuring it avoids walkway obstruction or
tripping hazards.
· Avoid injury by always making sure your fingers are not in the way when
attaching your LapLok to a table.
· Do not ingest Primer and/or Adhesive or let it contact your skin during use.
In case of any accident, immediately rinse the affected area with plenty of
soap & water. If skin irritation, redness, or any other adverse reaction
occurs, seek medical advice.
· Keep Primer and Adhesive away from open flames. These materials are
flammable and should be used and stored in a well-ventilated area, away from
any sources of ignition. If Primer is inhaled accidentally, move to an area
with fresh air and ensure proper ventilation. If respiratory discomfort or
difficulty persists, seek medical attention promptly.
· The included Primer or Adhesive should be just enough to use for the Parking
Tab, Mounting Arm, and laptop Rubber Feet. Discard any remaining primer with
caution. Keep Primer or Adhesive away from children & pets.
· Follow the manufacturer’s instructions for proper LapLok use.
NOTE: Primer may contain chemicals or substances that have properties that can
penetrate the skin and cause skin irritation, allergic reactions, respiratory
discomfort, or other adverse effects.
TM
Instruction Manual
LAPLOK PARTS/LABELS
Red LED
LAPLOK TOP VIEW
1/2 3/4 5/6 7/8 9/0
LAPLOK SIDE VIEW
Lock Button
Bolt Catch
Locking Pins
Green LED Top Upper Pad
Arm Mount
Number Buttons
Alarm
1 pc LapLok 1 pc Carabiner
1 pc Arm Mount
ALCOHOL WIPE
1 pc Alcohol Wipe
1 pc Parking Tab 4 pcs Laptop Rubber Feet
Lower Pad Lower Arm Release Lever Upright
Parking Tab
Mounting Plate
1 pc Primer Ampule
1 pc LapLok Warning Sticker
1 pc Protective Bag
1 pc Adhesive with Nozzle
Laptop Feet
LAPTOP BOTTOM VIEW
Arm
HOW TO USE YOUR LAPLOK
SCAN ME
For complete video instructions scan the QR code
STEP 1: Register Your Lock/Unlock Code
1. Go to https://reset.LapLok.com/ or scan the QR code to bring you to the
registration page.
2. Input your name, e-mail address, phone number, and 5-Digit Device Serial
Number found at the bottom of your LapLok.
3. A 4-Digit Verification Code will be sent to the phone number and e-mail
you entered.
4. Enter the 4-Digit Verification Code into the LapLok website’s registration
page.
5. Choose and enter a 3-5 Digit Lock/Unlock Code you would like to use with
your LapLok per instructions on Step 4.
6. Write your 3-5 Digit Lock/Unlock Code on the inside of the lever. NOTE:
Save your Lock/Unlock Code somewhere safe. See “Other Maintenance Tips” for
details.
STEP 2: Battery Activation
Batteries are already installed in the LapLok you received. 1. Pull back the
Locking Pins to unlock and raise the Top 2. Underneath the Top, locate and
activate the Switch, turning it to the
‘ON’ position. 3. Close the LapLok by pulling back the Locking Pins, then
release
them into the Bolt Catch. 4. To test if the Batteries are working, press the
Lock Button once.
When you see the RED LED blink twice, this indicates that battery is now
activated. NOTE: Under normal use conditions, Batteries should last about 5
years. If you need to replace them in the future, kindly refer to the
‘Replacing the Batteries’ section.
STEP 3: Attach the Mounting Plate, Arm, Parking Tab, and laptop Rubber Feet
1. Decide where on the bottom of your laptop you would like to attach the
Mounting Plate so it would be easy to rotate the 8″ Mounting Arm out to attach
it to your LapLok. The entire Mounting Plate and Arm should lie flat on the
bottom of the laptop and should not be on top of any bumps, ridges, vents, or
compartments. It should not be placed outside the edge of the laptop. If you
aren’t sure about the location, try taping it on as a test first.
Tip: For a right-handed person, it is recommended that you place it on the
lower left side on the bottom of the laptop, so it is easily accessible from
the side.
2. Use the included Alcohol Wipe to clean the location where you would like
to place the Mounting Plate.
3. Squeeze the Primer Ampule tube on the black circle that say `CRUSH’ until
the glass on the inside breaks and use an applicator to cover the area for
Mounting Plate installation. Wait 30 seconds for it to dry.
Warning: Do not touch Primer with your skin. Do not ingest it. See “Safety
Precautions” for details. You will also use the Alcohol Wipe and Primer for
the Parking Tab.
4. Peel the paper backing off the Mounting Plate then stick onto the primed
location, pressing down firmly for 30 seconds. Then wait 24 hours for the
adhesive to dry. A complete cure takes 3 days.
NOTE: You can use your laptop during the curing period, but do not apply force
on the Mounting Arm until fully dry.
Warning: The adhesive is permanent, so try to place it in the correct location
the first time.
5. Determine where the Parking Tab will hold the end of 8″ Mounting Arm,
clean the area with an Alcohol Wipe, use the Primer and let it dry, remove
paper tape, and glue Parking Tab to the laptop to prevent it from rotating
when not in use. Press down on it firmly.
6. To install the provided Rubber Feet, clean the 4 corners of the laptop
with the included Alcohol Wipe then apply the Primer to the area. Remove the
paper backing of the sticker from the Rubber Feet, apply small amount of the
included Adhesive, and press down firmly on the primed location for 30
seconds.
NOTE: This step is optional but adding the Rubber Feet will prevent laptop
wobble.
7. During the drying period of the attached components, we recommend to
consider affixing the LapLok Warning Sticker as a theft deterrent warning to
the lower right or left-hand corner of your laptop.
STEP 4: Initial Lock/Unlock Code Setting
The default Lock/Unlock Code is preset to 1-1-1 1. To change the default
Lock/Unlock Code to your newly registered
LapLok, press the Lock Button then press 1-1-1. When the Green LED blinks 5
times, this indicates that the LapLok is unlocked. 2. Press and hold the Lock
Button for 3 seconds. When you see that the Green LED blink twice, this
indicates that the Lock/Unlock Code can be changed. 3. Within 10 seconds,
enter your new registered Lock/Unlock Code, then press the Lock Button. 4.
Green LED blinks 3 times for successful Lock/Unlock code change. NOTE: Red LED
will blink 5 times indicating your LapLok is locked. Additionally, the user
has 10 seconds to enter their Lock/Unlock Code. If the Lock/Unlock Code is not
entered in that time frame or is incorrect, Red & Green LEDs will blink
alternately indicating the error.
STEP 5: Lock Your LapLok to a Table
LapLok works on tables up to 2″ thick 1. Press the Release Lever and move the
Lower Arm downward on the
Upright until there is enough room between the Upper and Lower Pads to slide
it over the edge of the table. 2. Pull back the Locking Pins to unlock and
raise the Top. 3. Slide your LapLok over the edge of the table. 4. Slide the
Mounting Arm into the mouth of the Upper Pad. 5. Move the Lower Arm upwards on
the Upright until the Lower Pad is tight against the bottom of the table and
the Upright is firmly against the edge of the table. NOTE: This step is
critical to your LapLok being effective in preventing theft.
6. Close the LapLok while pulling back the Locking Pins, then release the
Locking Pins into the Bolt Catch.
7. Arm your LapLok by pressing the Lock Button and enter your Lock/Unlock
Code and the Red LED will blink indicating it is armed.
NOTE: Once LapLok has been secured to the table, you can use the provided
Carabiner to fasten your bags onto the hole located at the end of the Upright.
NOTE: If LapLok removal is attempted while locked, a 30-second alarm will be triggered & both LEDs will blink. Entering your Lock/Unlock Code will turn off the alarm and unlock your LapLok.
NOTE: When the LapLok is locked, entering unique device-specific code also
unlocks the device. 6. You can now create a new Lock/Unlock Code using the
instructions
in the “Changing the Lock/Unlock Code” section.
TROUBLESHOOTING & CARE OF YOUR LAPLOK
STEP 6: Unlock Your LapLok from the Table
1. To unlock your LapLok, press the Lock Button, enter your Lock/ Unlock Code
and the Green LED will blink showing it is unlocked.
NOTE: If the user enters the Lock/Unlock code incorrectly, Red & Green LEDs
will blink alternately indicating the error. After 20 failed unlock attempts,
the alarm will sound for 30 seconds. 2. Pull back the Locking Pin and lift the
Top. 3. Press the Release Lever and pull the Lower Arm down. 4. Pull the
Mounting Arm out of the mouth of the Upper Pad.
Your laptop and LapLok are now free from the table.
HOW TO ADJUST THE SETTINGS
ADJUSTING THE ALARM VOLUME
A key LapLok feature is to detect movement and sound the alarm to deter theft
when someone tries to move it. Setting the alarm is an optional setting. 1.
Press the Lock Button then press and hold the (1) Button for 3
seconds. When you see the Green LED blink twice, this indicates that you can
now adjust the alarm volume. 2. Within 10 seconds, press both (1/2) Buttons
for high, both (3/4) Buttons for medium, both (5/6) Buttons for low, or both
(7/8) Buttons for no sound. 3. Green LED will blink twice when successfully
changed.
CHANGING THE LOCK/UNLOCK CODE
1. First, ensure your LapLok is unarmed, as the Lock/Unlock Code can only be
changed when unarmed.
2. Press and hold the Lock Button. When you see the Green LED blink twice,
this indicates that the Lock/Unlock Code can be changed.
3. Within 10 seconds, enter your new Lock/Unlock Code, then press the Lock
Button.
4. Green LED will blink 3 times for successful Lock/Unlock Code change. If
the change is unsuccessful, the Red LED will blink 3 times.
5. Register your new Lock/Unlock Code at https://reset.techlok.com/.
NOTE: Make sure to save your new Lock/Unlock Code. See “Other Maintenance
Tips” for details.
REMOVING THE MOUNTING PLATE AND ARM
1. To remove the Mounting Plate and Arm, use a butter knife, single-edge
razor blade, or similar tool as a lever to pry them off. This design is
intended to prevent theft.
2. Do the same to remove the Parking Tab.
FORGOTTEN LAPLOK’S LOCK/UNLOCK CODE
1. Go to https://reset.LapLok.com/ or scan the QR code in Step 1 to get to
the registration page.
2. Log in to your LapLok profile. NOTE: Unregistered users must first
register to log in to their profile. 3. After logging in, you will receive a
unique device-specific code to your
registered e-mail address or phone number. NOTE: For unregistered users, there
will be a 15-minute delay between sending and receiving the device-specific
code to reduce the chance of fraud. 4. On your LapLok, enter the unique
device-specific code you just
received. 5. If the unique device-specific code you entered into your LapLok
matches the code stored at the factory, your LapLok’s Lock/Unlock Code will
reset to 1-1-1. When you see the Green LED blink 3 times, that means a
successful Lock/Unlock Code reset.
REPLACING THE BATTERIES
LapLok uses two CR 2032 Batteries that should last about five years in normal
use conditions. We estimate normal usage to be three hours per week with the
siren sounding 2 times a year. The usage of LapLok will determine the
longevity of the Battery life. When your LapLok needs new Batteries, the Red
LED will blink 5 times. The Batteries will last about two weeks before they
become too weak to arm your LapLok.
1. To replace the Batteries, unscrew the four Screws on the top, lift the
Top, and unscrew the Screw on the bottom near the Switch at the bottom.
2. Open the Top and carefully remove the old Batteries and put in new ones.
3. Put the Top back to the LapLok and re-insert all the Screws. 4. To test if
the batteries are working, reactivate your LapLok by
activating the Switch on then press the Lock Button once. The Red LED will
blink twice if the battery replacement was succesful. 5. If they are not,
ensure that the new Batteries were correctly inserted.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>