Sunnydaze DECOR SL-443 Angel Falls 29 Inch Solar Fountain Instruction Manual
- May 15, 2024
- Sunnydaze DECOR
Table of Contents
- Sunnydaze DECOR SL-443 Angel Falls 29 Inch Solar Fountain
- Product Information
- Product Usage Instructions
- PARTS LIST
- FOUNTAIN ASSEMBLY
- SOLAR PANEL ASSEMBLY
- SOLAR PANEL OPERATION
- PERFORMANCE OF PUMP
- MAINTENANCE OF PUMP
- BATTERY INFORMATION
- TROUBLESHOOTING
- TECHNICAL DATA
- CARE INFORMATION
- WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Sunnydaze DECOR SL-443 Angel Falls 29 Inch Solar Fountain
Product Information
Specifications:
- Product Model: SL-443
- Includes: Angel & Stacked Stone Fountain, Angel Wings, Pump with 5m Cable, LED Light with 5m Cable, Solar Panel, Bracket, Tube, Spike
- Water Capacity: Approximately 2 gallons
- Power Source: Solar Panel (charger sold separately)
Product Usage Instructions
Assembly
Ensure all parts are accounted for before disposing of packaging.
- Attach the pump to the hose from the access panel on the back of the fountain body.
- Place angel wings into the notch on the back of the fountain.
Placement and Setup
- Select a level location to place the fountain. Assemble components on a smooth, clean surface to avoid scratching or damaging the finish.
- Fill the reservoir with water, ensuring the pump is completely submerged during operation.
- Connect the bracket, tube, and spike and attach the solar panel to the bracket as shown.
- Insert the spike into the ground and position the solar panel to face south for optimal sunlight exposure.
Operation
- Connect the pump and LED light cables to the solar panel (charger sold separately).
- The LED light is designed to only illuminate at night.
Solar Panel Operation
Press the [Power on/off] button for different modes:
- Continual ON Mode: Runs continuously until battery power runs out.
- 4-Hour Timer Mode: Runs for 4 hours and stops.
Maintenance
Clean the pump filter and impeller with clean water if the pump loses power or
stops working.
FAQ (Frequently Asked Questions)
-
Q: How do I know when the battery is low?
A: The indicator will show “Battery Low” when the battery pack needs to be charged. -
Q: Can I detach the water tube from the fountain?
A: Detaching the water tube will damage the fountain and void the product warranty. -
Q: How long does the LED light stay on?
A: The LED light is designed to only turn on at night.
Read the instructions carefully & save them for future reference.
PARTS LIST
- (1) Angel & Stacked Stone Fountain
- (1) Angel Wings
- (1) Pump with 5m Cable (inside solar panel box)
- (1) LED Light with 5m Cable (in the fountain)
- (1) Solar Panel, Bracket, Tube, Spike
Ensure all parts are accounted for before disposing of packaging.
FOUNTAIN ASSEMBLY
Select a level location to place the fountain. Assemble components on a smooth, clean surface to avoid scratching or damaging the finish.
NOTE:
The water tubing is built into the fountain. Take care when handling the water
tube; detaching the water tube from the fountain will damage the fountain and
void the product warranty.
- Place angel wings into the notch on the back of the fountain.
- Attach the pump to the hose from the access panel on the back of the fountain body. The LED light is preassembled into the fountain reservoir. The pump and LED light cables should exit out from the access hole, ready for connection to the solar panel.
- Fill the reservoir with water, ensuring the pump is completely submerged during operation; approximately 2 gallons.
SOLAR PANEL ASSEMBLY
- Connect the bracket, tube, and spike and attach the solar panel to the bracket as shown.
- Insert the spike into the ground. Position the solar panel to face south (in the northern hemisphere) to make the most of daylight hours. It is important to angle the solar panel towards the sun when the sun is at its highest point. Ensure trees, shrubs, or buildings do not shade the solar panel.
- Connect the pump and LED light cables to the solar panel (charger sold separately).
- Your new fountain is ready to use. Refer to the Solar Panel Operation information.
NOTE:
The LED light is designed to only illuminate at night.
Over time, the finish may gradually mellow in colour; this is part of the natural aging process.
SOLAR PANEL OPERATION
NOTE: The LED light is designed to only work at nighttime.
-
Continual ON Mode: Press the [Power on/off] button, and the top indicator light [continual on] will be lit — the pump will run continuously until the battery power runs out. The pump will automatically restart when the solar panel battery has been sufficiently charged with sunlight.
-
4-Hour Timer Mode: Press the [Timer modes] button until the second indicator light [4hrs Timer] is lit — the pump will run for 4 hours and stop. The pump will not run again until the solar panel is manually restarted.
-
Daily 4-Hour Timer Mode: Press the [Timer modes] button until the third indicator light [daily 4hrs Timer] is lit — the pump will run for 4 hours and shut down (in standby) for 20 hours; this operation will repeat daily at the same time. You can reset the pump’s daily start-up time by switching it on at a new desired time in this same mode. NOTE: The third indicator light will blink slowly when the pump has reached the 4-hour runtime and be on standby for the following 20 hours. To save battery power, the indicator light will automatically turn off. You can activate the indicator light to check its status with a single push of either button; the indicator light will be on for a while and shut off again.
-
BATTERY LOW [RED INDICATOR LIGHT BLINKING]:
Battery power is low, and the pump will stop running soon to protect the battery. The red indicator light will turn off after the solar panel receives enough sunlight for the battery to be recharged. -
PLEASE NOTE: This model allows for the battery pack to be charged with an original electric charger (sold separately). Only use the original battery charger as alternatives may damage the battery and will void the warranty. See contact information under WARRANTY to order the compatible charger.
PERFORMANCE OF PUMP
The performance of the pump depends on the orientation of the solar panel toward the sun and sunlight strength; pump performance is not guaranteed when the solar panel is in the shade or poor weather conditions. Max. Data is obtained during optimal conditions (refer to Technical Data); solar panel performance cannot be guaranteed if placed in the shade or during poor weather conditions. The performance of the pump also depends on the battery power level; the pump cannot operate if the battery power is low.
MAINTENANCE OF PUMP
This solar pump is designed to last for years if it is properly cleaned and maintained. If the pump starts losing power or stops working, clean the pump filter and impeller with clean water.
- Front Case
- Filter
- Impeller Cover
- Impeller
- Pump
BATTERY INFORMATION
The Li-ion backup battery pack, like all rechargeable batteries, has a limited life span and becomes less efficient with repeated charge/discharge cycles. As the capacity of the battery reduces over time, you may not achieve the full hours of operation.
If you find that the battery appears less efficient, try to “boost charge” it by turning the power off for 1 to 2 sunny days to allow the battery to achieve a maximum charge. Occasional “boost charges” will help prolong the battery life. If your battery pack still does not perform to expectations after a boost charge, replace it with a new pack.
BATTERY REPLACEMENT
IMPORTANT:
Only use original backup battery packs; alternatives may be incompatible,
which may damage the system and will void the warranty. See contact
information under WARRANTY (page 4) to order the compatible replacement
battery pack.
- Remove the screws (part 1) from the control panel cover (part 2) using a Phillips-head screwdriver.
- Disconnect the battery pack connector (part 3), and remove the battery pack (part 4) from the control panel base (part 5).
- Connect the new battery pack connector to the control panel base and insert the battery.
- Replace the panel cover and tighten the screws.
Dispose of the batteries by local laws and regulations.
TROUBLESHOOTING
- Check all solar panels, pumps, and LED light connections. Make sure connections are secure and the cables are plugged into the correct ports on the control panel.
- Ensure the solar panel is correctly positioned in a full-sun location and is not shaded by trees, shrubs or buildings; refer to page 2.
- Check the control panel and confirm it is set to the preferred operation setting; refer to page 3.
- If the [Battery Low] light is blinking, the battery pack power is critically low and requires charging. Switch off the pump and leave the solar panel in direct sunlight for at least 6 hours to recharge the battery pack.
- Check the water level to make sure the pump is fully submerged.
- Check the fountain tubing for kinks and obstructions. Also, check to make sure the tubing is tightly connected to the pump.
- Check the pump to make sure it is not blocked by or clogged with debris.
- The pump may be “air locked” from water levels getting too low or additional water being added. Turn the pump on/off several times to clear any air that may be trapped inside the pump.
TECHNICAL DATA
- MAX. PUMP WATER FLOW: 250LPH
- MAX. PUMP WATER LIFT: 90 cm
- PUMP WORKING VOLTAGE: DC8.4V~DC6.5V
- PUMP WORKING POWER: 1.2W~0.6W
- PROTECTION GRADE OF PUMP: IP68
- SOLAR PANEL: 2.5W-9V-0.277A
- SOLAR PANEL SIZE: 190 x 150 x 18 mm
- PROTECTION GRADE OF PANEL: IP44
- LI-ION BATTERY PACK: 7.4V/1.5Ah
- PROTECTION GRADE OF BATTERY BOX: IP44
- LED LIGHT WORKING VOLTAGE: DC7.4V
- LED LIGHT WORKING POWER: 0.15W
- PROTECTION GRADE OF LED LIGHT: IP68
CARE INFORMATION
- Check the water level frequently to ensure the pump remains submerged; never allow the pump to run dry as it will burn out the motor.
- Clean the fountain, pump, and solar panel regularly. Do not use abrasive materials or harsh chemicals, such as bleach or chlorine, to clean the fountain.
- Always shut off the power supply before cleaning and maintaining the fountain and the pump.
- During freezing weather, drain the fountain, disconnect the pump, cables and solar panel, and store it indoors; allowing ice to form inside the fountain will damage the fountain and void the warranty.
- The optimal temperature for lithium batteries is 10°C to 45°C, do not use the product beyond this temperature range.
IMPORTANT!
Fully charge the battery before storing. Over time, battery power discharges,
so if it is stored at no charge, there is a chance it won’t accept a charge
again. To avoid this problem, disconnect the pump and leave the solar panel in
direct sunlight for 1 or 2 days to ensure the battery has been recharged.
WARRANTY
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with the date of purchase as well as photos of the merchandise defect, must be provided. Photos are used to determine the cause of defects and for future quality control. Register your warranty at https://tiny.cc/SunnydazeWarranty.
If you have any questions, comments or concerns, feel free to contact us by phone at 833-982-1977, email: customerservice@sunnydazedecor.com, or via our Contact Us page at https://tiny.cc/SunnydazeContact.
- Purchase Date:
- Order/Customer Ref. Number:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>