TKO 9050 Functional Trainer Instructions
- May 15, 2024
- TKO
Table of Contents
TKO 9050 Functional Trainer
Product Diagram
Exploded Diagram
Parts List
| No. | Description | QTY | No. | Description | QTY |
|---|---|---|---|---|---|
| 1 | Left Upright Frame | 1 | 36 | Bearing 61800ZZ | 12 |
| 2 | Right Upright Frame | 1 | 37 | Bearing 61804ZZ | 4 |
| 3 | Rear Lower Support Frame | 1 | 38 | Pulley Φ95*24 | 4 |
| 4 | Top Support Frame | 1 | 39 | End Cap PT 501003 | 6 |
| 5 | Left Slide Frame | 1 | 40 | Foam Grip Ø243345mm | 2 |
| 6 | Right Slide Frame | 1 | 41 | Foam Grip Ø243160mm | 2 |
| 7 | Front Wheel Bracket | 2 | 42 | Foam Grip Ø243290mm | 2 |
| 8 | Pulley Frame | 2 | 43 | Hex Socket Head Bolt M10*50 | 10 |
| 9 | Adjusting Square Tube F40*2 | 2 | 44 | Hex Socket Head Bolt M10*65 | 6 |
| 10 | Guide Rod Ø20*1763 | 4 | 45 | Hex Socket Head Bolt M10*45 | 4 |
| 11 | Cleat for Shroud 86254 | 16 | 46 | Hex Socket Head Bolt M10*25 | 12 |
| 12 | Guide Rod Bush Φ30Φ20.230 | 4 | 47 | Hex Socket Head Bolt M8*15 | 18 |
| 13 | Pulley Bushing Φ18*14 | 8 | 48 | Nut M10 | 30 |
| 14 | Weight Stack 26010025.4 | 40 | 49 | Hex Socket Head Bolt M10*75 | 6 |
| 15 | Top Weight Plate 2476525.4 | 1 | 50 | Hex Sunk Screw M8*20 | 8 |
| 16 | Selector Rod Ø25*595 | 2 | 51 | Hex Socket Head Bolt M6*15 | 36 |
| 17 | Bearing Washer Ø25Ø211 | 2 | 52 | Flat Washer Ø11Ø202 | 64 |
| 18 | Curl Cover 107.6623 | 2 | 53 | Big Washer Ø8.6Ø222 | 16 |
| 19 | Bushing Ø10.2Ø12.75.5 | 12 | 54 | Rubber Washer Ø7Ø23T | 16 |
| 20 | Pin Ø18Ø12118*M10 | 2 | 55 | Hex Socket Head Bolt M5*10 | 10 |
| 21 | Spring Ø14Ø1.555 | 2 | 56 | Hex Socket Head Bolt M10*70 | 4 |
| 22 | Roller Ø54*49 | 6 | 57 | Limited Cushion 307020 | 2 |
| 23 | Knob Ø45*66 | 2 | 58 | Cross Pan Screw M6*12 | 4 |
| 24 | Ring Ø33*10 | 6 | 59 | Small Rubber Sleeve Φ15Φ618 | 4 |
| 25 | Magnetic Pin Φ10*98 | 2 | 60 | Cross Sunk Screw M5*10 | 8 |
| 26 | Cable Ø5*7600 | 2 | 61 | O-Ring Ø19*1.8 | 4 |
| 27 | Pulley Ø115*27.5 | 14 | 62 | Hex Cone Set Screw M6*4 | 10 |
| 28 | PVC Foot Pad 16912916 | 4 | 63 | Hex Cone Set Screw M6*6 | 12 |
| 29 | Cushion Ø80*25 | 4 | 64 | Hex Socket Head Bolt M10*40 | 2 |
| 30 | Shroud 17006004 | 2 | 65 | Flat Nut M12 | 2 |
| 31 | Sleeve Ø12*55 | 6 | 66 | Big Washer Ø9Ø242 | 2 |
| 32 | Rubber Bumper 60506 | 2 | 67 | Right Top Weight Plate | 1 |
| 33 | Rear Top Support Frame | 1 | 68 | End Cap Ø34.5Ø6.525 | 8 |
| 34 | T-Shaft Ø25*102 | 2 | 69 | Hex Socket Head Bolt M6*20 | 8 |
| 35 | Limited Plate 653080*4 | 2 |
| 70 | Long Bar | 1 |
|---|---|---|
| 71 | Short Handle | 1 |
| 72 | Tricep Rope | 1 |
| 73 | Ankle Strap | 1 |
| 74 | Chains | 2 |
| 75 | Hand Grips | 2 |
| 76 | Safety Hooks | 6 |
Assembly
Note: Before starting assembly remove all parts and hardware from the carton, ensure you have everything according to the list.
Step 1
Install Rear Lower Support Frame (3), Rear Top Support Frame (33) and Rear Top Support Frame (4) onto Left Frame (2) and Right Frame (1), using Hex Bolt M1025 (46) and Flat Washer Φ11Φ20*2 (52).
Step 2
Loosen and remove 2 Guide Rod Bush (12) from the Guide Rod (10); Then remove the Top Weight Plate (15) and The Selector Rod assembly from the Guide Rods.
Step 3
Re-Insert both Guide Rod (10) into the holes on the bottom of the Main Frame; Make sure the Rubber Bumpers are at the bottom of the Guide Rods.
Step 4
Install 20 Weight Stack (14) onto the Guide Rod (10); Re-install the Top Weight Plate (15) and Selector Rod assembly onto the top of the Weight Stack; Make Sure the holes of the Weight Stack for the Magnetic Lock Pin are the same direction.
Step 5
First Re-install the Guide Rod Bush (12) that was removed in STEP 2; Then
tighten both Hex Screw M 6*4 (62) with a wrench;
Repeat the same procedure for the other side.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>