TKO 713SP Leg Press Owner’s Manual

TKO 713SP Leg Press

Read this owner’s manual carefully before assembling or using TKO equipment. WARNING: Serious injury could occur if these safety precautions are not observed

Safety Precautions

• Before beginning any exercise program, consult your physician. Evaluate appropriate for your particular age and condition.
• If you experience any pain or tightness in your chest, irregular heartbeats, shortness of breath, faintness, or other unusual discomfort while exercising, stop and consult your physician before continuing.
• Make sure that the equipment(s) are set up and operated on a solid-level surface. DO NOT install or use the equipment on an uneven surface.
• Exercise equipment has moving parts. In the interest of safety, keep others, especially children, at a safe distance while exercising.
• Make sure there is enough room for access and operate the equipment(s) safely. inspect and maintain the equipment(s) regularly.
• Replace the worn or damaged parts/components immediately to ensure safety. Use a spotter.
• The back support cushion may drop when the knob is pulled. Hold the back support cushion when adjusting it.
• Make sure the pull pin is fully engaged before use.
• Lower the back support cushion to the lowest position when not in use.
• Warm-up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward. Never hold your breath while exercising.
• Remove all jewelry, including rings, chains, and pins before commencing the exercise. Always wear suitable clothing and footwear during exercise. DO NOT wear a loose machine.
• Rest adequately between workouts. Muscles tone and develop during these rest periods.
• Most exercise equipment is not recommended for small children. Children should not use the machine unless they are under adult supervision.

If you have any questions or need assistance please contact us at,
Customer Service: 866-856-3488 or 713-895-9270 e-mail: sales@tkostrength.com
Hours: Monday-Friday 8:30 am to 4:30 pm CT
© Copyright 2017, TKO Strength & Performance Inc. All rights reserved. TKO Strength & Performance Inc. 6387 Windfern Road, Houston, TX 77040 Phone + 713-895-9270 Fax + 713-934-8495 www.tkostrength.com

Product Diagram

Maximum Weight Limit: 200 KG / 440 lbs.

Instructions

Before beginning assembly please take the time to read instructions thoroughly. Please use the various lists in this manual to make sure that all parts have been included in your shipment. When ordering, use part number and description from the lists. Use only our replacement part when servicing. Failure to do so will void your warranty and could result in personal injury. The equipment is designed to provide the smoothest, most effective exercise motion possible. After assembly, you should check all functions to ensure correct operation. If you experience problems, first recheck the assembly instructions to locate any possible errors made during assembly. If you are unable to correct the problem, call your authorized dealer. Be sure to have your serial number and this manual when calling. When all parts have been accounted for, continue on.

Tools Required

Exploded Diagram

Parts List

NOTE : SOME OF THESE PARTS MAY COME PRE-INSTALLED

Measurement Guide

Assembly Instruction

Assembly of the equipment takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recommended to assemble the equipment by professional installers. You may find it quicker, safer, and easier to assemble this equipment with the help of a friend, as some of the components may be large, heavy or awkward to handle alone. You must assemble your product in a clean, clear, uncluttered area. This will enable you to move around the product while you are fitting components and reduce the possibility of injury during assembly.

NOTE
As with any assembled part, proper alignment and adjustment is critical. While tightening the fasteners, be sure to leave room for adjustments. Do not fully tighten the fasteners until instructed to do so. Be careful to assemble the components in the sequence presented in this guide.

Assembly
STEP 1Note：Hand Tighten Bolts and Nylon Lock Nuts.

STEP 2

Note: Hand Tighten Bolts and Nylon Lock Nuts.

STEP 3

Note: Hand Tighten Bolts and Nylon Lock Nuts.

STEP 4

Note: Hand Tighten Bolts and Nylon Lock Nuts.

Maintenance Schedule

Your equipment comes with a commercial/ maintenance decal. For personal, in- home use, please follow the home maintenance schedule listed above.

General Maintenance Information

Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:

• Check all pieces for signs of visible wear Or damage.
• Check springs in snap hooks and pull-pins for proper tension and alignment.
• If the spring sticks or has lost its rigidity, replace it immediately.

Upholstery:

• To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
• Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any abrasive cleaners or cleaners not intended for use on vinyl.
• Replace ripped or worn upholstery immediately.
• Keep sharp or pointed objects clear of all upholstery.

Decals:

• Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.

Nuts and Bolts:

• Inspect all nuts and bolts for any loosening and tighten if needed.
• Go through a re-tightening sequence periodically to ensure that all hardware is tensioned properly.

Anti-Skid Surfaces:

• “These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.

Belts and Cables:

• We use only high-quality belts and mil-spec cables.
• Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
• ‘While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
• Replace belts and cables immediately at the first signs of damage or wear. Do not use equipment until belts or cables have been replaced.

Seat Sleeves and guide Rods:

• Wipe down adjusting tubes with a dust-free rag before applying lubricant.
• Lubricate seat sleeves and Guide Rods with a Silicon or Teflon-based lubricant spray.

Linear Bearings:

• Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease (lithium, super lube, etc.) into the inside Of the bearing. Using your finger, press the grease into the ball-bearings and their tracks. repeat until the ball-bearing tracks are full of grease. Insert the shaft back into the bearing and wipe off excess grease.

PLEASE KEEP THIS FOR YOUR RECORDS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>