MOUNTUP B1MV3KZ Single Monitor Wall Mount Instruction Manual

MOUNTUP B1MV3KZ Single Monitor Wall Mount

Product Information

• Product Name: YZ2231_US2.0
• Compatibility: Designed for use in wood studs or solid concrete walls
• Maximum Weight Capacity: Each Monitor – 4.4 to 17.6 lbs (2 to 8 kg)
• Product Dimensions:
  • Wall Plate: 1.65″ / 42mm
  • Lower Arm Length: 6.65″ / 169mm
  • Upper Arm Length: 5.2″ / 132mm
  • Decorative Cover (Long): 5″ / 127mm
  • Decorative Cover (Short): 3.54″ / 90mm
  • Cable Cover: 0.89″ / 22.5mm
  • VESA Plate: 6.8″ / 173mm x 6.81″ / 173mm
  • Mounting Hole Pattern: 1927~.62~8101mm, 58mm, 324..9.9545//1/1710540mmmmmm, 2.95/75mm, 3.94/100mm, 4.5/114mm
  • Allen Key Sizes: 3mm, 6mm
  • Lag Bolt Size: W-A (ST6.3x60mm)
  • Concrete Wall Anchor Size: W-B (10x50mm)

Product Usage Instructions

1. Ensure that you have read the installation instructions and understand them fully.
2. Verify the compatibility of your wall construction. This product is suitable for use in wood studs or solid concrete walls. DO NOT install into drywall alone.
3. Check the weight capacity of your monitor. Each monitor should weigh between 4.4 to 17.6 lbs (2 to 8 kg). DO NOT exceed the maximum weight indicated.
4. Inspect all the supplied parts and hardware. Ensure that all parts are included and undamaged before starting assembly. If any parts are missing or damaged, do not return them to the dealer. Contact our customer service team for assistance.
5. Follow the provided dimensions and measurements to position the wall plate and mark the mounting holes on the wall.
6. If installing wood stud walls, use the supplied lag bolts (W-A) to secure the wall plate. If installing solid concrete walls, use the supplied concrete wall anchors (W-B).
7. Attach the lower arm (A) and upper arm (B) to the wall plate using the provided bolts (F) and Allen key (3mm).
8. Attach the VESA plate (E) to the back of your monitor using appropriate screws (not included).
9. Hang the monitor onto the arms and adjust the tilt and swivel as desired.
10. Attach the decorative covers (C1 and C2) and cable cover (D) for a clean and organized appearance.

Note: Always ensure that the installation is secure and that the wall can support five times the weight of the monitor and mount combined. Incorrect installation may result in product damage, property damage, or personal injury. If you have any questions or concerns, please contact our customer support before proceeding.

Safety Caution

Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

• This product is designed for use in wood studs or solid concrete walls.
  • DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the monitor and mount combined.
• Incorrect installation may result in product damage/property damage or body injury.
• We shall bear no responsibility for any damage or injury resulting from incorrect installation, incorrect assembly or misuse.

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!

Before Getting Started

Must Check Before Getting Started

• Verify Your Monitor Specifications:
• Verify Your Wall Construction:
  • CAUTION: Avoid potential personal injuries and property damage! Drywall covering the wall must not exceed 5/8 in (16 mm). Minimum wood stud size: nominal 2 x 4 in (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm).
  • CAUTION: Avoid potential personal injuries and property damage! Mount the wall plate assembly directly onto the concrete surface (no surface covering).
  • CAUTION: DO NOT install into drywall alone.

ATTENTION: Tension adjustment should be done only after monitor installation

WARNING: Gas Spring Arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury.

Product Dimensions

Parts and Hardware

Supplied Parts and Hardware

NOTE: Not all parts and hardware included will be used.

Extra Tools

Extra Tools You Need (Not Supplied)

INSTALLATION

Attach a VESA Plate to Monitor

1. Select Correct Monitor Screw Length

Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate screws and spacers for your monitor.

• Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.

Attach Arm to Wall

OPTION A: Wood Stud Installation

• Locate your studs. Verify and mark the center of the stud by finding the stud edges using awl and stud finder.

• Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the pilot hole locations.

• Drill pilot holes using a Ф3/16 in (Ф4.5mm) diameter drill bit.

IMPORTANT:

• Do not drill holes into where water pipes or electrical wires are located. Be sure to drill into the center of the stud.

Install wall plate using lag bolts with Socket Wrench, NO Electrodrill. No anchors when installed onto the wood studs.

CAUTION:

• To avoid potential personal injury or property damage:
  • All 3 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly.
  • Ensure the wall plate assembly is securely fastened to the wall before continuing to the next step.

Attach Arm to Wall

OPTION B: Solid Concrete Wall Installation

• Drill pilot holes using a Ф3/8 in (Ф10mm) diameter drill bit.

IMPORTANT:

• Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks.
• Use the hammer to knock anchors into the concrete wall. Be sure the anchors are seated flush with the concrete surface. Install wall plate using lag bolts and anchors with Socket Wrench, NO Electrodrill.

CAUTION:

• To avoid potential personal injury or property damage:
  • All 3 lag bolts MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly.
  • Ensure the wall plate assembly is securely fastened to the wall before continuing to the next step.

Hang Monitor

Install the Upper Arm (B) to the Lower Arm (A). Secure the arm by tightening the inside screw using 3mm Allen key (G). Attach Decorative Covers (C) to wall plate.

Slide the monitor onto the head of swivel arm, install the security bolt (F). Make sure the security bolt is installed before you rotate the monitor.

Adjustments (If necessary)
Tilt Adjustment

1. Loosen the tilting bolt.
2. Adjust monitor to your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.

Tension Adjustment

The gas spring is pre-set for a load-bearing range of 8.8 lbs -13.2 lbs. For the intended functioning of the mount, you will need to adjust the tension of the Arm under your monitor weight by 6mm Allen Key (H).

Note: Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount.

Situation 1: Arm falls down Upper Arm with monitor falls and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise (“+” direction) to increase gas spring tension until the arm can stay as intended.

Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.

Solution:
Turn the inside screw clockwise (“-” direction) to decrease gas spring tension until the arm can stay as intended.

Cable Management

Lower Arm
Remove the cable cover, run cables through the cable cover, then install the cable cover again.

Adjust monitor position and rotation.

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help. If you have any questions, please feel free to contact our customer support before returning. YZ2231_US2.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>