TKO 701IP Unilateral Plate Loaded Converging Incline Chest Press Instruction Manual

TKO 701IP Unilateral Plate Loaded Converging Incline Chest Press

Product Information

Specifications

• Model: 701IP
• Maximum Weight Limit: 150 KG / 330 lbs
• Manufacturer Website: www.tkostrength.com

Product Usage Instructions

Safety Precautions
Before using the Incline Chest Press, please read the owner’s manual carefully.

Follow these safety precautions:

• Consult your personal physician before starting any exercise program.
• Rest adequately between workouts to allow muscles to tone and develop.
• Exercise equipment is not recommended for small children without adult supervision.

Assembly Instructions
Tools Required: Not specified in the provided text.

Parts List

Assembly Steps

Step 1: Assemble the following parts:
Note: Hand-tighten bolts and nylon lock nuts during assembly.

FAQ

• What is the maximum weight limit for the Incline Chest Press?
  The maximum weight limit for the Incline Chest Press is 150 KG / 330 lbs.

• How can I contact customer service for assistance?
  You can contact customer service at 866-856-3488 or 713-895-9270 during Monday-Friday from 8:30am to 4:30pm CT. You can also email them at sales@tkostrength.com.

Website: www.tkostrength.com

Safety

Read this owner’s manual carefully before assembling or using TKO equipment. WARNING: Serious injury could occur if these safety precautions are not observed Safety Precautions

• Before beginning any exercise program, consult your personal physician.
• Evaluate appropriate for your particular age and condition.
• If you experience any pain or tightness in your chest, irregular heartbeats, shortness or breath, faintness or other unusual discomfort while exercising, stop and consult your physician before continuing.
• Make sure that the equipment(s) are set up and operated on a solid level surface.
• DO NOT install or use the equipment on an uneven surface.
• Exercise equipment has moving parts. In the interest of safety, keep others, especially children, at a safe distance while exercising.
• Make sure there are enough room for access and operate the equipment(s) safely. inspect and maintain the equipment(s) regularly.
• Replace the worn or damaged parts / components immediately to ensure safety. Use a spotter.
• Back support cushion may drop when knob is pulled. Hold the back support cushion when adjusting it.
• Make sure the pull pin is fully engaged before use.
• Lower the back support cushion to the lowest position when not in use.
• Warm up 5 to 10 minutes before each workout and cool down 5 to 10 minutes afterward.
• Never hold your breath while exercising.
• Remove all jewelry, including rings, chains and pins before commencing exercise.
• Always wear suitable clothing and footwear during exercise.
• DO NOT wear loose machine.
• Rest adequately between workouts.
• Muscles tone and develop during these rest periods.
• Most exercise equipment is not recommended for small children.
• Children should not use the machine unless they are under adult supervision.

If you have any question or need assistance please contact us at,

• Customer Service: 866-856-3488 or 713-895-9270
• e mail: sales@tkostrength.com
• Hours: Monday-Friday 8:30am to 4:30pm CT
• © Copyright 2017, TKO Strength & Performance Inc. All rights reserved. TKO Strength & Performance Inc. 6387 Windfern Road, Houston, TX 77040
• Phone: + 713-895-9270
• Fax: + 713-934-8495
• Website: www.tkostrength.com

Product Diagram

Maximum Weight Limit: 150 KG / 330 lbs.

Instructions
Before beginning assembly please take the time to read instructions thoroughly. Please use the various lists in this manual to make sure that all parts have been included in your shipment. When ordering, use part number and description from the lists. Use only our replacement part when servicing. Failure to do so will void your warranty and could result in personal injury. The equipment is designed to provide the smoothest, most effective exercise motion possible. After assembly, you should check all functions to ensure correct operation. If you experience problems, first recheck the assembly instructions to locate any possible errors made during assembly. If you are unable to correct the problem, call your authorized dealer. Be sure to have your serial number and this manual when calling. When all parts have been accounted for, continue on.

Tools Required

Exploded Diagram

Parts List

NOTE: SOME OF THESE PARTS MAY COME PRE-INSTALLED

ITEM NO.| DESCRIPTION| QTY| ITEM NO.| DESCRIPTION| QTY
---|---|---|---|---|---
1| Bottom Frame| 1| 32| Upper Handle Cover Assembly| 1
2| Right Upright Frame| 1| 33| Bottom Handle Cover| 1
3| Left Upright Frame| 1| 34| Safety Cover φ4735.3| 2
4| Middle Upright Frame| 1| 35| Safety Bushing Assembly| 3
5| Right Arm Frame| 1| 36| Adjustable Foot| 1
6| Left Arm Frame| 1| 37| Inner Bumper| 2
7| Middle Upright Frame| 1| 38| Plug PT60120| 4
8| Weight Horn| 2| 39| Plug φ48| 8
9| Adjustbale Handle Assembly| 1| 40| Bumper| 6
10| Weight Plate Storage| 6| 41| Ball Bearing| 4
11| Arm Frame Pivot Shaft| 2| 42| Button Head Cap Screw 3/8″-1638| 1
12| Seat Pad Support Frame| 1| 43| Flat Head Cap Screw M1235| 2
13| Pivot Shaft| 2| 44| Flat Head Cap Screw M1230| 4
14| Handle Pivot Shaft| 1| 45| Socket Head Cap Screw M1230| 20
15| Middle Pivot Shaft| 1| 46| Socket Head Cap Screw M1030| 4
16| Torsion Spring| 1| 47| Socket Head Cap Screw M1025| 4
17| Gap Spring Assembly| 1| 48| Socket Head Cap Screw M1020| 2
18| Snap Spring| 2| 49| Button Head Cap Screw M870| 2
19| Aluminium Cap φ32| 2| 50| Socket Set Screw M86| 4
20| Aluminum End Cap φ7617.6| 2| 51| Flat Head Cap Screw M616| 2
21| Aluminum End Cap φ60φ12.510.6| 4| 52| Philip Screw ST4.260| 8
22| Seat Pad| 1| 54| Cross Recess Head Screw M410| 2
23| Back Pad| 1| 55| Flat Washer φ13φ241.5| 20
24| Plug φ25| 2| 56| Flat Washer φ11φ202| 10
25| Grip| 2| 57| Spring Washer φ10| 2
26| Idler Wheel| 3| 58| Flat Washer φ9φ161.6| 2
27| Inner Slide| 1| 59| Nylon lock Nut M8| 4
28| Outer Slide| 1| 60| External Retaining Ring φ12| 2
29| Plastic Sleeve| 2| 61| External Retaining Ring φ15| 4
30| Plug RT50100| 1| 62| lock Nut 20134.5φ3.5| 8
31| Rubber Foot| 3| 63| Flat Head Cap Screw M630| 2

Measurement Guide

Assembly Instruction

Assembly of the equipment takes professional installers about 2 hours. If this is the first time you have assembled this type of equipment, plan to spend more time. It is strongly recommended to assemble the equipment by professional installers. You may find it quicker, safer, easier to assemble this equipment with the help of a friend, as some of components may be large, heavy or awkward to handle alone. It is important that you assemble your product in a clean, clear, uncluttered area. This will enable you to move around the product while you are fitting components and reduce the possibility of injury during assembly.
NOTE
As with any assembled part, proper alignment and adjustment is critical. While tightening the fasteners, be sure to leave room for adjustments. Do not fully tighten the fasteners until instructed to do so. Be careful to assemble the components in t he sequence presented in this guide.

Assembly
STEP 1

Note: Hand Tighten Bolts and Nylon Lock Nuts.

STEP 2

Note: Hand Tighten Bolts and Nylon Lock Nuts.

STEP 3

Note: Hand Tighten Bolts and Nylon Lock Nuts.

STEP 4

Note: Hand Tighten Bolts and Nylon Lock Nuts.

Maintenance Schedule

ROUTINE| COMMERCIAL MAINTENANCE| HOME MAINTENANCE| LATEST DATE ENTRY
---|---|---|---
Inspect;
Links, Pull Pins, Snap Locks, Swivels, Weight Stack Pins| DAILY| WEEKLY| | | | | | |
Clean; Upholstery| DAILY| WEEKLY| | | | | | |
Inspect;
Cables or Belts and their tension| DAILY| WEEKLY| | | | | | |
Inspect;
Accessory Bars, and Handles| WEEKLY| 3 MONTHS| | | | | | |
Inspect; All Decals| WEEKLY| 3 MONTHS| | | | | | |
Inspect;
All Nuts and Bolts, Tighten if needed| WEEKLY| 3 MONTHS| | | | | | |
Inspect;
Anti-Skid Surface| WEEKLY| 3 MONTHS| | | | | | |
Clean & Lubricate;
Guide Rods with a Teflon (PTFE) based lubricant (Superlube)| MONTHLY| 3 MONTHS| | | | | | |
Lubricate;
Seat Sleeves, Turcite Bushings, Linear Bearing| MONTHLY| 3 MONTHS| | | | | | |
Clean and Wax; All Glossy Finishes| 6 MONTHS| YEARLY| | | | | | |
Repack with Grease; Linear Bearings| 6 MONTHS| YEARLY| | | | | | |
Replace;
Cables, Belts and Connecting Parts| YEARLY| **** 3 YEARS| | | | | | |

Your equipment comes with a commercial maintenance decal. For personal, in home use, please follow the home maintenance schedule listed above.

General Maintenance Information

Links, Pull-Pins, Snap Hooks, Swivels, Weight Stack Pins:

• Check all pieces for signs of visible wear or damage.
• Check springs in snap hooks and pull-pins for proper tension and alignment.
• If the spring sticks or has lost its rigidity. replace it immediately.

Upholstery:

• To ensure prolonged upholstery life and proper hygiene, all upholstered pads should be wiped down with a damp cloth after every workout.
• Periodically take the time to use a mild soap or an approved vinyl upholstery cleaner to deter the onset of cracking or drying. Avoid using any abrasive cleaners or cleaners not intended for use on vinyl.
• Replace ripped or warn upholstery immediately.
• Keep sharp or pointed objects clear of all upholstery.

Decals:

• Inspect and familiarize yourself with any safety warnings or other user information posted on each decal.

Nuts and Bolts:

• Inspect all nuts and bolts for any loosening and t ighten if needed.
• Go through a re-tightening sequence periodically to ensure that all hardware is tensioned proper.

Anti- Skid Surfaces:

• These surfaces are designed to supply secure footing and need to be replaced if they appear worn or become slippery.

Belts and Cables:

We uses only high quality belt, and mil-spec cables.

• Visually inspect the belts and cables for fraying, cracking, peeling or discoloration.
• While the machine is not in use, carefully run your fingers along the belt or cable to feel for thinning or bulging areas.
• Replace belts and cables immediately at the first signs of damage or wear.Do not use equipment until belts or cables have been replaced.

Belt and Cable Tension:

• Referring to the Owners Manual, when belts or cables are used check all bolts attachments to be sure they are properly attached.
• Check slack in cables and re-adjust cable tension if needed.

Seat Sleeves, Guide Rods:

• Wipe down adj usting tubes with a dust free rag before applying lubricant.
• Lubricate seat sleeves and Guide Rods with a Silicon or Teflon based lubricant spray.

Linear Bearings:

• Referring to the Owners Manual carefully disassemble the bearing from its housing and place a finger full of light grease lithium, super lube, etc.) into the inside of the bearing. Using your finger, press the grease into the ball-bearings and their t racks. repeat until the ball-bearing tracks are full of grease. Insert the shaft back into t he bearing and wipe off excess grease.

PLEASE KEEP THIS FOR YOUR RECORDS

References

• TKO Strength & Performance

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>