Ingersoll Rand 2135QXPA Air Impact Wrench Instruction Manual
- May 15, 2024
- Ingersoll Rand
Table of Contents
Ingersoll Rand 2135QXPA Air Impact Wrench Instruction Manual
PRODUCT INSTRUCTION
| 1 2 3 | 5 | 6 | 7 | 9 | 10 |
|---|---|---|---|---|---|
| IR # – NPT | IR # – BS | inch (mm) | |||
| NPT | IR # | IR # | IR # | cm 3 | |
| C38341-810 | C383D1-810 | 3/8 (10) | 1/4 | MSCF33 | 10P |
Product Safety Information
Intended Use:
These Air Impact Wrenches are designed to remove and install threaded
fasteners
For additional information, refer to Air Impact Wrench Product Safety
Information Manual Form 04580916.
Manuals can be downloaded from ingersollrand.com
Power Management System
For models that include a power management system, the system allows operator
reduction of maximum output power in the forward direction. The power
management system does not affect the output power in the reverse direction.
To adjust the power, rotate the Power Regulator to the desired level
indicator. The power level indicators are for reference and DO NOT indicate a
specific power. The power output can be further reduced in forward or reverse
by using the variable throttle.
Product Specifications
**Models| ****Style| Drive| ****Impacts per
min.| Recommended Torque Range
---|---|---|---|---
Type| Size| Forward ft-lb (Nm)| Reverse ft-lb
(Nm)
2135QXPA2135QXPA-A| Pistol| Square| 1/2″| 1,250| 700 MAX(949 MAX)| 780
MAX(1057 MAX)
2135QXPA-2| Pistol| Square extended| 1/2″x 2″| 1,250| 700 MAX(949 MAX)| 780
MAX(1057 MAX)
2135PQXPA| Pistol| Square (Pin Retainer)| 1/2″| 1,250| 700 MAX(949 MAX)| 780
MAX(1057 MAX)
****Models| Impacting Sound Level dB(A) (ISO 15744)|
Free Speed Sound Level dB(A) (ISO 15744)|
Vibration (m/s²) (ISO 28927-2)
---|---|---|---
† Pressure (Lap )| ‡ Power (Law )| † Pressure (Lap
)| ‡ Power (Law )| Level**| *K
2135QXPA2135QXPA-A| 90.7| 101.7| 86.0| 97.0| 13.3| 4.6
2135QXPA-2| 90.7| 101.7| 86.0| 97.0| 9.7| 1.8
2135PQXPA| 90.7| 101.7| 86.0| 97.0| 13.3| 4.6
† Ka = 3dB measurement uncertainty
- K = Vibration measurement uncertainty
‡ Kwan = 3dB measurement uncertainty
WARNING
Sound and vibration values were measured in compliance with internationally recognized test standards. The exposure to the user in a specific tool application may vary from these results. Therefore, on site measurements should be used to determine the hazard level in that specific application.
Installation and Lubrication
Size air supply line to ensure tool’s maximum operating pressure (PMAX) at tool inlet. Drain condensate from valve(s) at low point(s) of piping, air filter and compressor tank daily. Install a properly sized Safety Air Fuse upstream of hose and use an anti-whip device across any hose coupling without internal shut-off, to prevent hose whipping if a hose fails or coupling disconnects. See drawing 47132782 and table on page 2. Maintenance frequency is shown in a circular arrow and defined as h=hours, d=days, and m=months of actual use. Items identified as:
- Air filter
- Regulator
- Lubricator
- Emergency shut-off valve
- Hose diameter
- Thread size
- Coupling
- Safety Air Fuse
- Oil
- Grease
Parts and Maintenance
When the life of the tool has expired, it is recommended that the tool be disassembled, degreased and parts be separated by material so that they can be recycled. Original instructions are in English. Other languages are a translation of the original instructions. Tool repair and maintenance should only be carried out by an authorized Service Center. Refer all communications to the nearest Ingersoll Rand office or distributor.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>