BANG OLUFSEN 01 Beoremote Halo Remote Control For Accessing Ausic User Guide

BANG OLUFSEN 01 Beoremote Halo Remote Control For Accessing Ausic User Guide

Important safety instructions

• Read these instructions.
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over
• Refer all servicing to qualified service personnel. Servicing is required whenthe apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Using USB-C chargers of poor quality may trigger false operations during charging.
• WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on the equipment.

The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

This device meets the EU requirements (1999/519/EC) on the limitation of exposure of the general public to electromagnetic fields by way of health protection.

Electrical and electronic equipment, parts and batteries marked withthis symbol must not be disposed of with normal household wastage,it must be collected and disposed of separately to protect theenvironment.

Your Bang & Olufsen retailer will advise you of the correct way of disposal in your country

Important

• Avoid placing the product in direct sunlight or direct artificial light, such as a spotlight.
• Make sure that the product is set up, placed and connected in accordance with the instructions.
• Do not place any items on top of your product.
• The max ambient temperature should not exceed 45 °C.
• WARNING: No naked flame sources, such as lighted candles should be placed on the product. The supplied plug and mains cord are specially designed for the product. Do not change the plug, and if the mains cord is damaged, you must buy a new one from your Bang & Olufsen retailer.
• Do not subject the product to high humidity, rain or sources of heat.
• The product is intended for indoor use in dry, domestic environments only (not applicable to portable products).
• Leave enough space around the product for adequate ventilation.
• Do not attempt to open the product. Leave such operations to qualified service personnel.

FCC Statement

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  a ) This device may not cause harmful interference, and
  b ) This device must accept any interference received, including interference that may
  cause undesired operation.

• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide  reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Warning Statement for UNII devices
Caution:
User should also be advised that

1. the device for operation in the band 5150‐5250 MHz is only for indoor use to reduce the potential for harmful interference to co‐channel mobile satellite systems;
2. the maximum antenna gain permitted for devices in the bands 5250‐5350 MHz and 5470‐5725 MHz shall comply with the e.i.r.p. limit; and
3. the maximum antenna gain permitted for devices in the band 5725‐5825 MHz shall comply with the e.i.r.p. limits specified for point‐to‐point and non point‐to‐point operation as appropriate. High‐power radars are allocated as primary users (i.e. priority users) of the bands 5250‐5350 MHz and 5650‐5850 MHz and that these radars could cause interference and/or damage to LE‐LAN devices

Innovation, Science, and Economic Development Canada (ISED) Notices

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Warning Statement for Antenna limitation (e.i.r.p)
Under Innovation, Science, and Economic Development Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science, and Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent is otropically radiated power (e.i.r.p.) is not more than that necessary for successful communication

Radio Frequency (RF) Exposure Information

The radiated output power of the Wireless Device is below the Innovation, Science,and Economic Development Canada (ISED) radio frequency exposure limits. TheWireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized.

This device has also been evaluated and shown compliant with the ISED RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person’s body)

This table is prepared in accordance with the provisions of SJ/T 11364.
O : Indicates that this hazardous substance contained in all of the homogenous materials for this part is below the limit requirements specified in GB/T 26572.
X : Indicates that this hazardous substance contained in at least one of the homogenous materials for this part is above the limit requirements specified in GB/T 26572

Beoremote Halo
Get started easily
Download the Bang & Olufsen App
Bang & Olufsen App



To set up your product, download the Bang & Olufsen App from the Google Play Store or Apple App Store.

From this app you can set up and get the most out of your Beoremote Halo.

When you first start the Bang & Olufsen App, you will be asked to create a user account.

To set up your Beoremote Halo, click to add a new product. If you already have an account this can be found under settings.

To set up your Beoremote Halo, click to add a new product. If you already have an account this can be found under settings.

Follow the steps in the app to set up WiFi on your Beoremote Halo and update the software.

Once this is finished, your Beoremote Halo is set up and ready to use.

Daily use of Beoremote Halo
Learn how to use your Beoremote Halo for daily operation.

The display of your Beoremote Halo will light up when you approach it due to the built-in proximity sensors.

Use the touch screen to control music on your connected devices.

Simply tap to play and pause the music. Use the arrows to change between next andprevious tracks or radio stations.

Turn the aluminium ring to control volume.

The last used speaker is always displayed when approaching Beoremote Halo.

You can change the speaker you want to control by tapping the speaker name at the top of the screen. This will bring you to a list of all connected speakers. The list scrolls horizontally

You can easily select sources built-in to your connected Bang & Olufsen speakers and play your favourite radio stations by swiping down on the display. The source list will slide down into view.

Adding new products
Use the Bang & Olufsen App to add or remove products to control with your Beoremote Halo.

The products need to be set up in the Bang & Olufsen App as well.

In the Bang & Olufsen App, select your Beoremote Halo to see the products connected to your account. Here you can easily add them to the list of products which can be controlled by your Beoremote Halo.

Favourites
You can quickly access your preferred listening experiences using favourites.

Find the four favourite buttons by swiping up on the display of your Beoremote Halo.

To play a saved favourite, simply press the button.

To save a favourite, long press on your chosen favourite and the current listening experience will be saved to it.

Please note that for voice enabled speakers, favourites can only be saved locally on the speaker.

Sources
By swiping down on the display you can easily change between the sources built into your connected products, such as Deezer, TuneIn or products connected through Line-In.

Here, you also have the option to join in on a listening experience already playing from a speaker set up in your network

Learn more

How to access settings
Access the settings of your Beoremote Halo by selecting Beoremote Halo in the product menu.

Get to the product menu by tapping the speaker name at the top of the screen, which will bring you to a list of all connected products. The list scrolls horizontally.

Here you can control the brightness of the screen.

Factory reset
You can reset your Beoremote Halo to factory settings by long pressing the small button found under the front cover.

After approximately 10 seconds a notification will appear on the screen before it fades out.

Now the Beoremote Halo is ready for first-time setup again.

CMIIT ID: XXXXYZNNNN
Manufacturer: Bang & Olufsen a/s
Factory: PCI Kunshan Electronics Company Limited
Model: Beoremote Halo Wall
Model Number: 3055
Input/Rating: DC 12-30V ⎓ 0.5 A
Made in China

Documents / Resources

| BANG OLUFSEN 01 Beoremote Halo Remote Control For Accessing Ausic [pdf] User Guide
01 Beoremote Halo Remote Control For Accessing Ausic, 01, Beoremote Halo Remote Control For Accessing Ausic, Halo Remote Control For Accessing Ausic, Remote Control For Accessing Ausic, Control For Accessing Ausic, For Accessing Ausic, Accessing Ausic
---|---

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>