EUREKA FORBES 167 Classic Booster

Product Information

• Specifications
  • Model: AG SELECT CLASSIC+ UV BOOSTER
  • Dimension (W X D X H): 313 mm X 167 mm X 423 mm
  • Net weight: 3 kg (Approx.)
  • Purification Technology: UV Sediment cartridge, Carbon BlockTM, Mineral guardTM, Active Copper MaxxTM With Zinc Booster Cartridge, UV- E-boiling, BiotronTM Cartridge

Product Usage Instructions

• Prerequisites for Installation
  • Product installation should be done only by a trained Eureka Forbes Service Technician.
  • The input water must be tested for Total Dissolved Solids (TDS) and Total Hardness.

Multi-Stage Purification Process

dust, mud, and sand from water.
2| Chemi-block – Dust-free Bacteriostatic Activated Carbon that
adsorbs colour, odour, excess chlorine & organic impurities from
incoming water.

FAQs

• Q: Can I install the product myself?
  • A: No, product installation should be done only by a trained Eureka Forbes Service Technician.
• Q: How often should I replace the UV lamp?
  • A: The UV lamp has a life of 8000 burning hours as per the manufacturer’s specifications. It is recommended to replace it after this duration.

PREREQUISITES FOR INSTALLATION

Product installation should be done only by a trained Eureka Forbes Service Technician only

1. Input water must be tested for Total Dissolved Solids ( and Total Hardness
   • Install the product in a dry ventilated place Keep it away from direct sunlight, heating devices or areas below 10 o C
   • The purifier should be placed in an area which is free of ants/insects/other pests
   • Ensure that the input tap water temperature is in the range of 10 o 40 o C Avoid installation to a hot water tap as it can damage the filters
2. The input water pressure to your water purifier should be within the recommended range (refer variant specific technical specifications table) If the input water pressure is more than specified, installation of a PRV (Pressure Regulating Valve is mandatory If the input water pressure is less than specified, installation of an external booster pump is recommended
3. In the case of Aquaguard ® Select Classic with Booster pump, ideally inlet water tube should draw water from an offline water source (like a bucket) The product also be connected to a pressure on line water supply like a loft tank Note Strictly recommended to install Aquaguard ® Select Classic with Booster pump where water pressure does not exceed 1 0 kg/cm 2 if the input water pressure is more then installation of a suitable PRV (Pressure Regulating Valve) is mandatory
4. Ensure that the filters are flushed thoroughly and independently for 3 to 5 minutes to remove fine particles present in the filter, before the installation of the unit
5. After installation, run the purifier for 5 to 10 minutes and drain the water

Input water quality usage limitations

1. If the input water iron content is more than that prescribed in the technical specifications, use of an iron remover** is recommended as a pre treatment
2. If the input water turbidity is more than that prescribed in the technical specifications or comprises colloidal particles, the use of a special filter** is required as a pre-filter
3. If the input water TDS is more than 1 000 ppm (mg/ or input water hardness is more than 300 ppm (mg/ use of a Membrane life enhancer** is recommended (applicable only for RO variants
4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications Available at an extra cost.

LED INDICATION CHART FOR YOUR AQUAGUARD ® SELECT

PURIFICATION PROCESS

MULTI-STAGE PURIFICATION PROCESS

suspended particles such as dirt, dust, mud and sand from water. It removes very fine turbidity from the water
2| Chemi-block| Dust-free Bacteriostatic Activated Carbon block filter cartridge| Adsorbs colour, odour, excess chlorine & organic impurities from the incoming water. Its unique Particle Trap Filter entraps any released microparticles.
3| Mineral GuardTM| Microcontroller-based electronic impulse producer| Generates electronic impulses that prevent scaling/deposition of Calcium and Magnesium on the Quartz Glass tube of the UV reflector chamber, thereby ensuring the best UV Penetration through Quartz Glass into the water column and at the same time keeping essential minerals like Calcium and Magnesium intact in the water
4| UV e-boiling| Germicidal UV Lamp| UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses & protozoa, thereby making it safe to drink.
5| Active Copper Maxx™ With Zinc Booster Cartridge*| A patented technology with a unique combination of naturally occurring vital minerals like Copper and Zinc along with calcium and magnesium| Enhances the taste of the water and increases the level of essential minerals with the add-on goodness of copper and zinc along with calcium and magnesium which helps in improved health and body functions. At the same time, balancing the pH of the water makes it healthy. Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification (Acceptable limit)
6| BiotronTM cartridge| Patented multiple magnetic field (MMF) generating device| Breaks complex water molecules into fine micro-clusters, making water more bio-permeable, so that your body can easily absorb the goodness of water, along with its much-needed nutrients.

TECHNICAL SPECIFICATIONS

| TECHNICAL PARAMETER| SPECIFICATION

---|---|---
| Model| AG SELECT CLASSIC+ UV
PRODUCT SPECIFICATION
1| Dimension (W X D X H)| 313 mm X 167 mm X 423 mm
2| Net weight| 3 kg (Approx.)
3| Purification Technology| UV
4| Standard Purification supplied| Sediment cartridge, Carbon BlockTM, Mineral guardTM, Active Copper Maxx™ With Zinc Booster Cartridge, UV- E-boiling, BiotronTM Cartridge
ELECTRICAL SPECIFICATIONS
1| Power Rating| 20 Watts (Max.)
2| Power Supply| Input 230V AC, 50Hz.
3| UV LAMP| 11 Watts
4| UV Lamp life| 8000 burning hours (as per UV lamp manufacturer spec.)
5| Operating Voltage Range| 150 to 280 V AC, 50 Hz
RECOMMENDED INPUT WATER PARAMETERS
1| Input water pressure range**| 0.3 to 2 kg/cm2
2| Input Iron content (Max.)| 0.1 mg/L
3| Input Chlorine content (Max.)| 0.2 mg/L
4| Input water turbidity (Max.)| 5 NTU
5| Total Dissolved Solids (TDS)| Up to 200 mg/L
6| Input Water Temperature range| 10°C to 40°C

Technical Specifications are subject to change without prior notice.
Note:

• The performance data presented in the table is applicable under standard laboratory conditions Actual performance may vary depending on the input water quality, water pressure and condition of filters.
• If the pressure is higher than the maximum specified, the use of a pressure reducing valve is mandatory, If the pressure is lower than the minimum specified, use an external booster pump recommended The above accessories are available with our company at an additional cost.
• Warranty Void if the product is not installed as per recommendations.

Standard Test Conditions:

• Feed Water Quality TDS Max: 200 mg/L

Pressure:

• 1 kg/cm 2, Turbidity: 1 NTU (Max.), Temperature: 25 C,
• Chlorine: below 0.2 mg/L, Iron: below 0.1 mg/L
• Life: 6000 Liters Actual performance may vary based on input water conditions Turbidity& Pressure

| TECHNICAL PARAMETER| SPECIFICATION

---|---|---
| Model| AG SELECTED THE CLASSIC+ UV BOOSTER
PRODUCT SPECIFICATION
1| Dimension (W X D X H)| 313 mm X 167 mm X 423 mm
2| Net weight| 3.5 kg (Approx.)
3| Purification Technology| UV BOOSTER
4| Standard Purification supplied| Sediment cartridge, Carbon BlockTM, Mineral guardTM, Active Copper Maxx™ With Zinc Booster Cartridge, UV- E-boiling, BiotronTM Cartridge
ELECTRICAL SPECIFICATIONS
1| Power Rating| 43 Watts (Max.)
2| Power Supply| Input 230V AC, 50Hz.
3| UV LAMP| 11 Watts
4| UV Lamp life| 8000 burning hours (as per UV lamp

manufacturer spec.)

5| Operating Voltage Range| 150 to 280 V AC, 50 Hz
RECOMMENDED INPUT WATER PARAMETERS
1| Input water pressure range**| 1.0 kg/cm2
2| Input Iron content (Max.)| 0.1 mg/L
3| Input Chlorine content (Max.)| 0.2 mg/L
4| Input water turbidity (Max.)| 5 NTU
5| Total Dissolved Solids (TDS)| Up to 200 mg/L
6| Input Water Temperature range| 10°C to 40°C

Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table applies to understanding laboratory conditions Actual performance may vary depending on the input water quality, water pressure and condition of filters. If the pressure is higher than the maximum specified, the use of a pressure reducing valve is mandatory, If the pressure is lower than the minimum specified, use an external booster pump recommended The above accessories are available with our company at an additional cost.

1. If water is to be drawn from a low height loft tank then please ensure that the minimum pressure available is at least 0.2 to 0.3 kg/cm 2. Also, ensure that the maximum water pressure should not exceed 1.0 kg/cm 2
2. If water is to be drawn from bucket the please ensure that the height of the unit from the bucket is not more than 1.5m, input water pressure in this case is not applicable. Warranty Void if the product is not installed as per recommendations.

Standard Test Conditions:

• Feed Water Quality TDS Max: 200 mg/L
• Pressure: 1 kg/cm 2 , Turbidity: 1 NTU (Max.), Temperature: 25 C,
• Chlorine: below 0.2 mg/L, Iron: below 0.1 mg/L
• Life: 6000 Liters Actual performance may vary based on input water conditions Turbidity& Pressure

LIFE OF CONSUMABLE CARTRIDGES

• Note: Please refer to Standard Test Conditions for filter life As per manufacturer’s spec.

WARRANTY TERMS & CONDITIONS

1. The Products are warranted against manufacturing defects for twelve (12) months from the date of the original purchase
2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized agent adequate opportunity to inspect test and remedy them for which the Customer will deposit the goods at its own expense, if so, required by the Company with the Company’s Office/Service Centre along with the original invoice in the city where they are sold.
3. The Inspection and Test Report of the company’s office/service centre will be final and binding under the warranty for determining defects, repairs/alterations required or carried out or certifying work of the goods thereafter.
4. AQUAGUARD ® may require initial setting, and post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the company’s service centre.
5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty.
6. Notwithstanding anything to the contrary contained or implied by this warranty:
   • a) The company’s liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the customer.
   • b) The company’s liability under this warranty shall be limited only to defects in the goods that occur under the conditions of normal operation of the goods and their proper and prescribed use. The warranty does not cover or extend to defects that are determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse, misuse, faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or damage caused by lightening or other electrical disturbances or interruptions, dismantling or re-installation at a different location.
   • c) The company’s liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorized agency at the location specified in the invoice and such installation is undertaken by the company or its authorized agent or franchisee.
   • d) Consumable items mentioned in the consumables table are subject to normal wear and tear and are not covered by this warranty. Please refer model specific components given in the user manual under the table “consumable cartridges”.
   • e) Reverse Osmosis Membrane warranty is for 1 year (or) 6,000 liters (whichever is earlier) from the date of installation, on the condition that the input water is as per the standard test conditions for RO variants (provided in the section “Technical specifications table”), mentioned in the user manual. If the RO membrane gets clogged within the warranty period, it will be cleaned/repaired/replaced free of charge as deemed fit by the company-authorized service person/centre after inspection. (At applicable for RO models only.)
   • f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or according to this warranty in respect of death or injury to the customer or any other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than per the user manual or by due to any other cause or circumstances beyond the control of the company.
   • g) The company’s liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the customer to the company for the goods stated in the invoice.

General
For this warranty, the following expressions shall have the following meanings respectively:

1. The ‘Goods’ shall mean the goods described in the Order Form.
2. The ‘Customer’ shall mean the original purchaser of goods from the company.
3. The ‘Company’ shall mean EUREKA FORBES LIMITED.
4. Aquaguard means and includes AQUAGUARD ®, AQUAGUARD ® Select and Sure from AQUAGUARD ®.
5. General Terms & Conditions shall mean the terms and conditions agreed upon by the customer and the company printed on the Order Form.
6. Invoice’ shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the total purchase price thereof and name of the customer.
7. User Manual shall mean the instructions for Installation, use and maintenance provided through a QR code along with the Product supplied by the company.
8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time to time without any prior notice.
9. Any disputes are subject to Mumbai Jurisdiction only.

Post warranty

1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms
2. In case the customer does not wish to enter the Service Contract, he has the option of calling the company’s service centre to have his AQUAGUARD ® services on an actual basis, i.e., by paying the labour cost and spares needed to attend to that service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places where the company has its service centres.
3. If during such servicing the company must replace or repair defective components or parts, the customer shall be required to pay for the same as per the company’s prevailing price list.
4. Eureka Forbes Limited reserves the right to offer an annual maintenance contract/ensure the availability of spares only up to 7 years from the date of invoice. *Conditions apply.

ENVIRONMENT PROTECTION

• “Protection” has always been our motto and guiding principle. We care for the environment.
• We urge you to recycle the packaging material or take it to the nearest recycling facility rather than dispose of it with the rest of your waste.
• Your product has been designed to work for many years, however, should you wish to upgrade or replace your old product, remember to help protect the environment by disposing of it at your local e-waste disposal centre.
• Should you have any queries, the nearest authorized service centre of Eureka Forbes will be able to guide you.
• Allow us to become your environment partner; together we can make the world a cleaner place.

HEALTH PROTECT TM

For your safety the specially designed and electronically authenticated purification cartridges of Aquaguard ® ensure our promise of ‘pure & healthy water or no water’ always. In the unlikely usage of a ‘non genuine’ purification cartridge that could potentially deliver unsafe water an indication light will draw your attention. For your complete protection, it even shuts down the purification process. Not just this, it also alerts you in advance when the Aquaguard ® purification cartridges are reaching the end of their usable life (6000 litres). So that you can contact the authorized Eureka Forbes Service Centre for your required ‘ genuine ‘ purification cartridge replacement. ^ Sediment Cartridge, Chemi block TM, Active Copper Maxx TM with Zinc Booster Cartridge, Alkaline Cartridge. Not including premature chocking of the purification cartridges due to poor water conditions. vis. silt etc. Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specific copper and Zinc as compared to earlier products of Aquaguard with only Copper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>