FEZIBO 40 Electric Standing Desk Instruction Manual

FEZIBO 40 Electric Standing Desk

PACKAGE LIST

• **Left Leg

**

• **Right Leg

**

• **Leg Base

**

• **Drive Rod

**

• **Hand Controller

**

• **Power Supply

**

• **Side Plate

**

• **Beam

**

• **Board

**

• **Board

**

• Screws M6×8mm
  

• **Screws M5×15mm

**

• **Screws M6×35mm

**

• **Screws M6×12mm

**

• **Wrench

**

• **Wrench

**

• **Cable Clip

**

• **Wooden Pin x6 (48″ 120cm)

**

• Desk **connection Plate

**

• **Cable Hole Cover

**

• **Desk Connection Hook

**

• **Screwdriver

**

SPARE PARTS

• **Screw M6×8mm

**

• **Screws M5×15mm

**

• **Screw M6×35mm

**

• **Screw M6×12mm

**

• **Wooden Pin

**

INSTALLATION INSTRUCTIONS

Note: Ensure that all bolts are 100% locked.

Please read the installation instructions carefully before installation.

Step 1

Use Wrench F, install Beam 8 to the Left Leg 1 and Right Leg 2 with Screws A*6.

Step 2

Use a Screwdriver L and use Screws D4 to mount the Side Plate 72 to Left Leg 1 and Right Leg 2 respectively.

Step 3

Using Wrench F, install Leg Base 32 to the Left Leg 1 and Right Leg 2 respectively with Screws C8.

Step 4

1. Loosen the knob

2. Insert the drive rod into the hex hole and turn the transmission rod clockwise until the Right leg goes to the lowest position.

3. Insert the other end of transmission rod to the slot on the leg(You may rotate the rod slightly for better installation).
   Use a small hex wrench to tighten the pre-installed set screws to secure the drive rod to the slot

4. Tighten the knob

Step 5

First, fix Boards (9a&9b) and the Wooden Pin H4 (40”), and then fix the Wooden Pin H6 (48”).

Step 6

Use Screwdriver L with Screws B10, install Desk Connection Plate I 3 to the middle of the Boards , and Desk Connection Hook K*2 to both sides of the Boards .

Step 7

With a Screwdriver L, fix the legs to the Board (9a & 9b) with Screws B*10.

Step 8

With a Screwdriver L, fix the Hand Controller 5 to the edge of the Board (9a & 9b) with Screw B*2.

Step 9

Connect Power Supply 6 and Hand Controller 5 and fix it with Cable Clip G*2.

Step 10

Insert Cable Hole Cover J*2 into the hole in the Board 9a.

NOTE: Ensure that all bolts are 100% locked.

Using the Controller

LED Display: Press any key once to wake up the display.

Press the [1] or [2] or [3] button, the desk will move to the height that was previously set for that button.

Long press the button to raise the desk continually, and desk will stop when the button was released
or at the max height (118cm)

Long press the button to lower the desk continually, and desk will stop when the button was released or at the lowest height (72cm)

Memory button setting: Adjust desk to the height you prefer, then long press the button [1] or [2] or [3] until LED display shows H1 or H2 or H3 and flashes for about 3 seconds. Once the LED display shows the height you already set, the height memory setting is done.

Reset Press and hold the button for 5 seconds, and the screen will show’ RES.’ Continue holding until the desk goes down to its lowest level and comes back up slightly.

Protection Mode Error Codes

Hot| Overheat protection: When the motor operates continuously, it will stop running to prevent damage caused by overheating. Wait for a period of time (15-20minutes) before making any further height adjustments.
E10| Sensor malfunction warning: Motor safety sensor cannot be detected. Please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
E20| Overloading Warning: Over the max of loading weight. Power off, take the things off the desk, power back on, and try again.
E02| Operation Status Warning: The desk stops moving if vibration, impact, or incline is detected. If this detection is incorrect, follow the reset instructions before continuing use.
E32| Overvoltage Protection: Input voltage too high. If the correct AC adapter is being used, please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
E31| Undervoltage Protection: Input voltage too low. If the correct AC adapter is being used, please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.
–| Cable Disconnection Warning: Please power off, unplug the cables of the controller, wait for 5 minutes, then plug in the cables and connect the power again, and perform RES settings again.

Customer Support

Technical Support

(909)637-7665 | (909)637-7593

Thank you for choosing this product. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

Other Info nan@upgradedecorshop.com

nan@upgradedecorshop.com

(909)637-7665 | (909)637-7593

EST 9:00AM–17:00PM

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>