LASER TREE LT-80W-AA-PRO High Power Laser Module User Manual

LASER TREE LT-80W-AA-PRO High Power Laser Module

LASER MODULE INTRODUCTION

Parameters

Outline dimension (Unit: mm)

Standard configuration

Air pump suggestion:
• Air pressure and capacity: ≥Q.027kPa, 27L/min

LASER MODULE CONNECTION DESCRIPTION

PIN Definition

Built-in driver board

| Yellow: PWM
---|---
| Black: GND
| Red: Power (+12V/24V)

Driver adapter

① Output A: 3PIN connector
② Output B: 3PIN connector
③ Input A: 4PIN connector
④ Input B: 4PIN connector
⑤ Input C: 3PIN connector
⑥ Input D: 2PIN connector
⑦ DC Input: 12V or 24V power adapter
⑧ Power Switch: EXT->External power supply
INT->lnternal power supply
⑨ Power indicator: It is red when the power cable is connected correctly.
⑩ TTL/PWM indicator: It is green when the TTL/PWM cable is connected correctly.

Connection

Please check whether the laser module is compatible with your engraving machine before connection.

A. Check the voltage parameter of your engraving machine.
Please ensure that your engraving machine voltage and laser module are matched.

B. Check the pin definition of the main board on your engraving machine.
Please ensure your engraving machine main board has “PWM”,” GND” and “DC” ports.

“A” &”B”are both compatible.
Connect the laser module to the main board of your engraving machine directly.

Reference picture

Only voltage is not matched.

The voltage parameter of your machine are not matched to the module.

connector on P-DA-01.
---|---
| Connect the cable of the laser module to the Output A connector on P-DA-01 .
| Connect the 24V power adapter to the DC Input connector on P-DA-01 . Push the switch to EXT position and the power is provided by external power adapter.

Reference picture

Only control board pin definition is not matched.

Situation 1: The definition of connector on the engraving machine main board is not pin-to-pin.

Please rearrange the wire sequence of the cable to make each wire is well matched with the pin definition on the main board.

Reference picture

Situation 2: Please use P-DA-01 if the main board of your engraving machine is not 3pin, such as 2pin.

Laser Module

|

Machine

|

Solutions

---|---|---

3PIN

|

2PIN

|

Driver Adapter

Other pins

|

Driver Adapter

| Connect the cable of the your engraving machine to the corresponding input connector on P-DA-01 .
---|---
| Connect the cable of the laser module to the Output A connector on P-DA-01 .

Reference picture

LASER MODULE REFERENCE SETTINGS

For cutting

The focal length of the L T-80W-AA-PRO laser module is 45mm.

When cutting, you only need to make the focus located a bit lower than the surface of materials.

Reference settings for cutting

For engraving

When engraving, please ensure that the focus is located on the material surface.

Reference settings for engraving

PRECAUTIONS AND MAINTENANCE

Precautions

| Please wear laser goggles to protect your eyes when you use this laser module.
---|---
| Please ensure that the air pump is turned on before you start cutting. If not, the smoke will contaminate the lens.
| This laser module doesn’t support hot plug, hot plug may cause damage to the laser module.

Maintenance

| When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.
---|---
| When you replace the air nozzle, please ensure that your operation will not pollut the lens. Finger prints or dust on the lens will weaken the output power of the laser module, or even damage the lens.
| When you find the cutting ability decreases, the lens might be not clean. Please use a clean alcohol swab to clean it according to the following figure.

• For more information about maintenance, please contact us atlasertree@micost-optotech.com.

SAFETY ORECAUTION

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>