TILTA WLC-T05-HWC Nucleus Nano II Wireless Lens Instruction Manual

HVIN:WLC-T05 /WLC-T05-HWC)
TILTA WIRELESS LENS CONTROL SYSTEM

WLC-T05-HWC Nucleus Nano II Wireless Lens

DISCLAIMER
Thank you for purchasing a TILTA product.
Before using this product, please carefully read this document to ensure that the product has been set up correctly. The final interpretation of this document and all related documents for this product belongs to TILTA. For updates, please visit the official website at www.tilta.com for the latest product information. TILTA reserves the right to modify any information in this manual at any time without prior notice and without assuming any responsibility.
By using this product, you are deemed to have carefully read the disclaimer and warnings, understood, agreed, and accepted all the terms and content of this statement. You promise to take full responsibility for the use of this product and any consequences that may arise.
You commit to using this product only for legitimate purposes and agree to this term as well as any related regulations, policies, and guidelines set by TILTA.
TILTA is not responsible for any damages, injuries, or legal liabilities caused directly or indirectly by the use of this product. Users should follow all safety guidelines mentioned in this document, including but not limited to those mentioned. Despite the above provisions, consumer rights are still protected by local laws and regulations and are not affected by this disclaimer.
TILTA is a trademark of Shenzhen TILTA Technology Co., Ltd. and its affiliated companies. Product names, brands, and other trademarks appearing in this document are trademarks or registered trademarks of their respective companies.

WARNING & PRECAUTION

Before using this product, please strictly follow the instructions below. Our company assumes no responsibility for any consequences caused by improper operation or misuse.

ACCESSORY REQUIREMENTS

Charging at temperatures higher than 40°C (104°F) or lower than 5°C (41°F) may result in decreased battery performance, swelling, leakage, overheating, and other damage.
Do not store the battery in an environment exceeding 60°C (140°F). The ideal storage temperature is 22°C (71.6°F) to 28°C (82.4°F).
The battery must be charged with the charging equipment provided by TILTA. TILTA will not be responsible for any consequences resulting from charging with non-TILTA official equipment.

OPERATING ENVIRONMENT

This device contains strong magnets. To avoid magnetic interference, please keep it away from magnetic cards, IC cards, implantable medical devices (such as pacemakers), hard drives, RAM chips, and other devices that may be affected.
Use the battery in an environment with a temperature between -20°C (-4°F) and 45°C (113°F). Excessive temperatures can cause the battery to swell abnormally, catch fire, or even explode. Before using the device in a low- temperature environment, it is recommended to fully charge the battery at room temperature to extend its service life.
Do not place the device near flammable or combustible materials (such as carpets and wooden products) while charging. Always pay attention to the charging process to prevent accidents.
Store the device in a dry environment, with an ideal storage humidity not exceeding 40%.

BATTERY SAFETY

[Warning] This device is equipped with a non-removable built-in battery. please do not attempt to replace the battery yourself, as this may damage the battery or the device.

• Do not use the battery in environments with strong electrostatic or magnetic fields, as this may cause internal circuit failures in the device.
• Do not expose the battery to high temperatures or place it near heat-generating devices, such as sunlight, heaters, microwaves, ovens, or water heaters. Overheating the battery may cause it to explode.
• Do not disassemble or modify the battery, insert foreign objects, or immerse in water or other liquids, as this may cause the battery to leak, overheat, catch fire, or explode.
• The electrolyte inside the battery is highly corrosive. If it accidentally comes into contact with your skin or eyes, rinse immediately with clean water for at least 15 minutes and seek medical attention.
• Do not throw the battery into fire, as this can cause it to catch fire and explode.
• Do not drop, squeeze, or puncture the battery. Avoid subjecting the battery to external pressure, which may cause internal short circuits and overheating.
• Do not use damaged batteries.
• Do not store the battery for an extended period after it has been completely discharged, to avoid entering a deep discharge state that can cause damage to the battery cells, rendering it unable to be used again.
• Be sure to fully discharge the battery before disposing of it in a designated battery recycling bin. Batteries are hazardous chemicals and must not be disposed of in regular trash bins. For details, please follow the local laws and regulations regarding battery  ecycling and disposal.
• If the battery cannot be fully discharged, do not dispose of it directly in a battery recycling bin; instead, contact a professional battery recycling company for further processing.

MAINTENANCE & CARE

• Please keep the device clean and free of sand, dust, and other foreign objects. Use a clean, dry cloth to promptly clean any debris on the product.
• Do not subject the device and its accessories to strong impacts or vibrations, as this may damage them and cause device failure.
• If the device collides with a hard object or the screen is broken due to a strong external impact, do not touch or attempt to remove thebroken parts. Instead, immediately stop using the device and promptly contact TILTA customer service.

NOTE: The device will generate slight heat during operation, which is normal.

INTRODUCING NUCLEUS NII HAND UNIT

1. 1.6=inch Circular Touch Screen
   Lens & Camera Data/Parameter Display

2. [REC] Button
   01 Single Press: REC Run/Stop Function
   02 Long Press 3s: Power On/Off
   Long Press 8s: Force Power Off

3. Control Rocker
   Control the Assigned Motor

4. [FUNC] Button
   01 Set Marks
   02 Hold to Calibrate Lens

5. Rotation Limit Switch
   Switch TF/OF Mode (TF Mode: Compatible with TILTA Wireless Follow Focus Systems;
   DF Mode: Compatible with DJJ Fallow Focus Systems )
   Switch Up to TF Mode ( Limits Focus Knob Rotation to 360 Degrees )
   Switch Down to DF Mode ( Focus Knob can Rotate Freely )

6. NATO Mount
   For Mounting the Hand Unit

7. Contact Pins
   Communicates with DJERS2/RS3 Pro

8.  Safety Pin
   Prevents Accidental Disconnection

9. Tie Down
   Lock to Secure the NATO Accessory

10. USB-C Port
    For Charging/Firmware Updating

11. Hand Wheel
    Rotate to control the Assigned Motor

FEATURES

| Circular Touch Screen
Dynamic Interaction/350ppi
---|---
| USB-C
Supports PD Fast Charging
| Built-in High Capacity
Battery with Extended Life
Continuous Operation for Over 7 Hours & Smart Standby

TECHNICAL DATA

• Material: Aluminum Alloy+Plastic
• Dimensions: 737253mm
• Weight: 175g
• Color: Black

BATTERY USAGE GUIDELINE

Built-in Battery Capacity 3.7V 1800mAh 6.66Wh

1. Operating Temperature: Charging: 0°Cto 45°C (32°F to 113°F); Discharging: -10°Cto 60°C (14°F to 140°F)
2. Storage Temperature: -5°C to 45°C (23°F to 113°F)
3. Operating Humidity: 45+20% (Recommended)
4. Warranty Period: 12 months and less than 500 charge cycles

INTRODUCING NUCLEUS NII MOTOR

TECHNICAL DATA

• Material: Aluminum Alloy+Plastic
• Dimensions: 83463imm
• Weight:80g Color: Black

INDICATOR LIGHT

White: Motor is not assigned to any function
After pairing is complete, the motor will display the following colors according to the handwheel settings to distinguish which motor corresponds to which hand unit control option.
Purple: Focus Green: Iris Blue: Zoom Yellow: Other

ATTACHING MOTOR TO LENS

(1) Attaching Lens Gears
Attach part (1) lens gear to the lens, following the indicated direction, Secure part (2) to complete the assembly,
NOTE The adjustable lens gear included in the kit or the TILTA Seamless Focus Gear Ring (sold separately) enables lens adaptation to the follow focus ring system with a 0.8 pitch gear.
Note: If the lens comes with a 0.8 module gear ring, skip this step.
(2) Attaching Rod Holder & 15mm Rod
Attach the (3) rod holder to the 1/4″ thread on the cage side arm, and tighten the screw, Then, secure the 15mm rod (4) to the rod holder, which will be used to attach the motor,
(3) Attaching Motor
Mount the (5) motor onto the 15mm rod, adjust the motor angle, and then engage the M0.8 gear with the adjustable lens gear and then tighten the tie down (6) to complete the assembly.
Note : Rey The kit includes a 15mm Rod Holder to 1/4″-20 Adapter (side-mounted) and a 15mm rod. If needed, you can purchase additional TILTA Rod Holder
Accessories for motor attaching, as shown in the image on the left.

POWERING MOTORS & CABLING

You can use TILTA’s Universal Power Bank Holder or F970 Battery Plate V2 (sold separately) for supporting various power options, in order to supply power to the focus motor via the USB-C port (PD protocol).
Attaching the Universal Power Bank Holder (TA-UPBH-B)
Attach the Universal Power Bank Holder to a 1/4″-20 thread, Tighten the screw and then secure the power supply equipment (such as a power bank). Attaching the F970 Battery Plate V2 (TA-BTP2-F970-B)
Attach the F970 Battery Plate to a 1/4″=20 thread.
Tighten the screw and then secure the power supply equipment (such as an F970/F550 battery).
POWERING MULTIPLE MOTORS
When using multiple motors simultaneously, you can connect them in series using the USB-C (PD protocol) port for a synchronized power supply. When connecting multiple motors in series, use Port 2 input to Port 1 output; for the last motor, use Port 1 input to Port 2 output, connect the Run/Stop Cable to control the camera.
CONNECTING 2 MOTORS:
CONNECTING MULTIPLE MOTORS (23):
RUN/STOP CABLE:
Connect one end of the Run/Stop Cable to the motor’s USB-C port 2, and the other end to the camera. You can then control the camera’s recording functions and settings using the hand unit.

INTRODUCING THE MAIN UI

The Nucleus-N Il hand unit Ul consists of Three Main Screens and Four Settings Menus.
The Three Main Screens include the Camera Control Interface, Motor Parameter Interface, and Focus Distance Interface.
The Four Settings Menus are Connect Settings, Function Settings, System Settings, and Motor Settings.
After turning on the device, the hand unit will enter the Motor Parameter Interface. In this interface, swipe left or right on the screen to switch between the Three Main Screens. Swipe up from the bottom of the screen to access the Four Settings Menus. Swipe left or right to select the desired settings menu and tap the center icon to enter the detailed settings interface.
Swipe up from the bottom Camera Control Interface- REC
Motor Parameter Interface

1. WiFi Status

2. Wireless Channel Indicator
   A: Auto Search M: Manual Search ;
   Number : Channel No,

3. Motor Parameter (0-999)

4. Motor Indicator
   Focus Indicator/lris Indicator/Zoom Indicator

5. Additional Settings (Swipe Up)

6. AF/MF Switch Button

7. Battery Information

8. Bluetooth Status

9. REC/STBY Indicator

10. Focus Knob Range Indicator

11. Set Mark Button (A/B)

12. Touch Screen Lock Button
    Camera Control Interface- STBY****

13. Camera Settings Lock Button

14. REC/STBY Indicator

15. Iris Info

16. IS0 Info

17. Communication Protocol Info

18. Recording Run Time

19. Shutter Speed Info

20. Color Temperature Info

21. Resolution/Date Rate/Frome Rate
    Focus Distance Interface
    

22. Focus Distance

23. Lens Manufacturer

24. Lens Model

25. Kris info

26. Focal Range Info

27. Set Mark Button

USE THE HAND UNIT

USE INDEPENDENTLY
The Nucleus-N Il hand unit can be used independently.
The focus motor can be controlled by rotating the handwheel or using the control rocker.
Some camera settings can be controlled through the touch screen.
ATTAGH TO OTHER ACCESSORIES
The Nucleus-N II hand unit features a standard NATO quick-release mount, allowing it to be attached to any NATO rail. (such as NATO rail on the side of a camera cage/DJI RS2, RS3 Pro gimbal/rear operating handle for DJI Ronin/ monitor cage, etc..)
Note: When assembling and disassembling, pay attention to the contact pins on the back of the hand unit to prevent damage from external force.
USE WITH THE NUCLEUS NANO II CONTROL HANDLE (as shown below)
Attach the hand unit to the Control handle using the NATO mount, lock the tie down to secure.

IC CAUTION
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

To maintain compliance with RSS-102 RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body. Use only the supplied antenna.

FCC WARNING

This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body. Use only the supplied antenna.

NUGLEUS NANO II WIRELESS LENS CONTROL SYSTEM
For more instructions, please scan the QR code in the image.
Enter the model number WLC-T05 to obtain the electronic version of the product manual.

|

WWW.TILTA.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>