VISUAL COMFORT 700FJWDS Windsor Pendant Instruction Manual
- May 15, 2024
- VISUAL COMFORT
Table of Contents
VISUAL COMFORT 700FJWDS Windsor Pendant
Product Information
Specifications:
- Product Name: Windsor Pendant
- Model Numbers: 700FJWDS_, 920FJWNDSR 1.0
- Usage: Indoor dry locations above the finished floor
- Cable Length: Adjustable
- Lamp Types: Incandescent (MAX 35 Watt MR16 Halogen) or LED (MAX 8 Watt LED MR16 Bi-Pin)
Product Usage Instructions
Adjusting the Fixture Height:
- Back out the set screw on the tip of the connector using the provided Allen wrench.
- Back out the set screw on the conical connector with the provided Allen wrench.
- Pull out the coaxial cable and cut it to the desired length.
- Twist the end of the coaxial cable gently.
- Tap the conical connector on a hard surface to secure the plate inside.
- Feed and push the coaxial cable into the conical connector until it stops.
- Tighten the set screw on the conical connector firmly.
- Continue pushing the coaxial cable into the connector while rotating to ease feeding the inner wire.
Replacing the Lamp:
- Disconnect power to the fixture before replacing the lamp.
- Lift the shade to access the socket.
- For incandescent versions, use a MAX 35 Watt MR16 Halogen lamp. For LED versions, use a MAX 8 Watt LED MR16 Bi-Pin Lamp.
- Remove the old lamp and insert the new lamp pins into the socket.
- Lower the shade back in place.
FAQ:
-
Q: Can this product be used outdoors?
A: No, this product is only suitable for indoor dry locations. -
Q: What should I do if the lamp is not turning on?
A: Make sure the power is connected, and if using an LED lamp, check that it is inserted correctly into the socket. -
Q: How do I clean the fixture?
A: Use a soft, dry cloth to gently wipe down the fixture. Avoid using harsh chemicals or abrasive materials.
GENERAL PRODUCT INFORMATION
This product is ETL listed and suitable only for indoor dry locations and approved for use at any height above the finished floor.
Adjust The Fixture Height
- Back out (do not remove) the set screw on tip of the connector with the provided Allen wrench.
- Back out (do not remove) the set screw on the conical connector with the provided Allen wrench.
- Pull the coaxial cable out.
- Cut the coaxial cable to the desired length.
- Gently twist the end of the coaxial cable between thumb and forefinger.
- Tap the conical connector on a hard surface with the set screw facing down, so the plate inside drops into place.
- Feed and push the coaxial cable into the conical connector. The coaxial cable will come to a stop point after being inserted 3/4″ into the conical connector.
- Keep pushing the coaxial cable into the connector while rotating the connector to ease feeding the inner wire into the tip of the connector. The outer wrapped wire will start wrinkling while being inserted another 1/2″ into the connector.
- Look into the sight hole on the top of the connector to make sure that the inner wire is contacting the end of the connector.
- Hold the coaxial cable in place and tighten the set screw on tip of the connector with the provided Allen wrench. Make sure this set screw connection is tight.
- Firmly tighten the set screw on the conical connector.
- Pull the coaxial cable toward the fixture to smooth the wrinkles.
Replacing the Lamp
CAUTION: To reduce the risk of a burn or electric shock during relamping, disconnect the power to the fixture.
- Lift the shade up to expose the socket.
- For incandescent versions, use MAX 35 Watt MR16 Front Cover Halogen lamp.
- For LED versions, use provided MAX 8 Watt LED MR16 Bi-Pin Lamp.
- Remove the old lamp.
- Push the new lamp pins completely into the socket.
- Lower the shade back on top of the stopper.
SAVE THESE INSTRUCTIONS!
Visual Comfort & Co.
7400 Linder Ave, Skokie, IL 160077
800.969.3347
www.visualcomfort.com
©2023 Visual Comfort & Co.. All rights reserved. The Visual Comfort & Co. logo
is a registered trademark of Visual Comfort & Co. Visual Comfort & Co.
reserves the right to change specifications for product improvements without
notification
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>