CLIM ART ART Deflettori Auto Wind For Compatible with Nissan Instruction Manual

May 15, 2024
Clim Art

Instruction Manual

ART Deflettori Auto Wind For Compatible with Nissan

CLIM ART ART Deflettori Auto Wind For Compatible with
Nissan

SIDE WINDOW DEFLECTORS
Before installing the deflectors, please read the manual. Incorrect installation of deflectors can cause damage or injury.

COMPLETE SET

4 Piece Set (2 Piece Set) (the product may differ from the illustration in the instructions)CLIM ART ART Deflettori Auto Wind For Compatible with Nissan -
Fig 1

1 Front driver side window deflector
2 Front passenger side window deflector
3 Rear driver side window deflector
4 Rear passenger side window deflector
5 Instruction manual
6 Plastic blade (1 piece)
7 Alcohol wipe (2 pieces)
8 Fastening bracket (4 pieces)

ATTENTION! Protective film, DO NOT REMOVE!

THE TERMS USED IN THIS INSTRUCTION MANUAL

CLIM ART ART Deflettori Auto Wind For Compatible with Nissan - Fig
3 FRONT DEFLECTORS

  1. Deflector frame
  2. Rear section of deflector
  3. Front section of deflector

CLIM ART ART Deflettori Auto Wind For Compatible with Nissan - Fig
4

SET 1 REAR DEFLECTORS CLIM ART ART Deflettori Auto Wind For Compatible
with Nissan - Fig 5

SET 2  REAR DEFLECTORSCLIM ART ART Deflettori Auto Wind For Compatible
with Nissan - Fig 6

ATTENTION! IMPORTANT INFORMATION!
ATTENTION! Read the installation instructions carefully and follow ALL POINTS in the text!
Incorrectly installed deflectors can be dangerous. If in doubt, please contact Customer Service.

  • If the safety features of the vehicle do notallow you o close the window, deactivatethem (check the vehicle’s nstruction manual).
  • After instaling the deflectors, leave the car windows closed for 72 hours. If the temperature s below 62.5°/17°C, leave closed an additional 24 hours or longer, if possible.
  • We strongly recommend installing the deflectors at temperatures between 59°F/15°C and 77°F/25°C.
  • IMPORTANT INFORMATION! Clean the grease off the installation surface with a supplied alcohol wipe. If the deflector installation process is not followed, the manufacturer does not guarantee the secure instalation of the product.

FRONT DEFLECTORS

ATTENTION! Clean the installation surface with a supplied alcohol wipe. If the deflector installation process is not followed, the manufacturer does not guarantee the secure installation of the product.

1.1| Make sure the car windows are clean and dry. Next, lower the side windows completely and clean the grease offthe inner surface of the window channel with an alcohol wipe.| 1.2|  Remove the protectiveliner from the tape on the deflector.
---|---|---|---
1.3|  Place the front section of the deflector on the lower frame of the window as shown in the llustration.| 1.4| Shift the deflectorforward, fitting the deflector frame into the channel completely. Make sure the deflector is placed above the lower window frame.
1.5| Bending the center partof the deflector outwards, inert the vear section ofthe deflectornto the channel, leaving a gap above it.| 1.6| Starting with the front section of the deflector, insert it into the window channel.
1.7| Immediately after installing the deflector, adjust it position by carefuly pulling it outwards.| 1.8| To ensure the best nstallation of the deflector and the best adhesion between the tape and the surface of the rubber seal, itis strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflctor.
1.9| Raise the window until it touches the deflector. Carefully pulling the deflector outwards,roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.| 1.10| Repeat ponts 1110 1.9 on the apposit side of the vehicle

SET 1 REAR DEFLECTORS (FoRr FOUR-DOOR VEHICLES)

2.1| Make sure the car windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.| 2.2| To position the fixture, bend the edge of the rubber seal from the back frame of the window by 2-3 inches by using the provided special plastic blade as shown in the illustration.
---|---|---|---
2.3| Place the fastening bracket in the channel and return the rubber seal to its original position. 1- Rubber seal; 2 – Fastening bracket; 3 – Plastic blade; 4 – Metal body frame of the door.| 2.4| The illustration demonstrates how to position the fastening bracket. 1 – Rubber seal; 2 – Deflector; 3 – Fastening bracket; 4 – Glass; 5 – Metal body frame of the door.
2.5| Bend the edge of the rubber seal from the front frame of the window by 2-3 inches (5-7cm). Place the fastening bracket in the channel and return the rubber seal to its original position.| 2.6| Remove the protective liner from the tape on the deflector.
2.7| The deflector must be installed starting at the rear. To do so, place the rear section of the deflector frame into the channel and move the front section upwards. Position the entire deflector frame into the window channel, placing the frame between the fastening brackets and the rubber seal as is shown in the illustration 2.4.| 2.8| Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
2.9| To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, it is strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.| 2.10| Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
2.11| Repeat points 2.1 to 2.10 on the opposite side of the vehicle.| |

SET 2 REAR DEFLECTORS (FOR FOUR-DOOR VEHICLES)

2.1| Make sure the vehicle windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.| 2.2| Remove the protective liner from the tape on the deflector.
---|---|---|---
2.3| The deflector must be installed starting at the back. To do so, place the back part of the deflector frame into the channel and move the front part upwards. Position the entire deflector frame into the window channel.| 2.4| Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
2.5| To ensure the best installation of the deflector and the adhesion between the tape and the surface of the rubber seal, itis strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.| 2.6| Raise the window until it touches the deflector. Care- fully pulling the deflector outwards, roll the window up with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
2.7| Repeat points 2.1 to 2.6 on the opposite side of the vehicle.| |

CONGRATULATIONS!
Your unique and durable deflectors are installed for you to enjoy! From this moment on we hope you enjoy their appearance!

  • If you have any questions about warranty, technical aid, or requests for missing (lost) parts, do not hesitate to contact Customer Service: by phone: +1-929-999-41 89, by email: customerservice@sparklinesinc.com.
  • Weare happy to serve you and your vehicle to produce high-quality products that have an ideal it easy installation, and enjoyment with everyday use.

  +1-929-999-41-89
customerservice@sparklinesinc.com
301121.778

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals