Barricade S6 Running Boards Instruction Manual
- June 1, 2024
- BARRICADE
Table of Contents
Barricade S6 Running Boards
INSTRUCTION MANUAL
2019-2024 CHEVY SILVERADO/GMC SIERRA 1500 CREW CAB
(Incl. Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra
1500 Limited)
2020-2024 CHEVY SILVERADO/GMC SIERRA 2500/3500 CREW CAB
(Incl. Diesel models with DEF tanks)
PART#WB-CS171BD/WB-CS171SD
2019-2024 CHEVY SILVERADO/GMC SIERRA 1500 CREW CAB
(INCLUDES DIESEL MODELS W/DEF, 2022 SILVERADO 1500 LTD AND 2022 SIERRA 1500
LIMITED)
2020-2024 CHEVY SILVERADO/GMC SIERRA 2500/3500 CREW CAB (INCLUDES DIESEL
MODELS W/DEF)
PARTS LIST:
| 1 | Driver/left side Running Board | 16 | 8-1.25mm x 30mm Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right side Running Board | 16 | 8mm Lock Washers |
| 4 | Driver/left side Mounting Brackets | 32 | 8mm x 24mm x 2mm Flat Washers |
| 4 | Passenger/right side Mounting Brackets | 16 | 8mm Nylon Lock Nuts |
| 8 | 8mm x 35mm Double Bolt Plates |
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
1. Start the installation under the driver side of the vehicle. Locate the 6
plugs along the bottom edge of the body. Mounting Brackets will bolt to the
1st, 3rd, 4th and 6th threaded mounting holes, (Figures 1—6). Remove the
plastic plugs from each mounting location. Directly above each threaded insert
is a top mounting location on the side of the body panel. Hold a Bracket up in
place to help determine the correct mounting holes to use along the body.
NOTE: Thread an 8mm Hex Bolt into the threaded inserts to clear paint as
required.
2. Select (1) Driver/left side Mounting Bracket. Starting at the front of the
driver/left side, bolt the Mounting Bracket to the factory threaded holes with
(2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figure 7).
Do not tighten hardware at this time.
3. Repeat Steps 1 & 2 to install (3) Driver/left side Mounting Brackets on
the remaining mounting locations along the body panel.
4. Select the Driver/left side Running Board. Use the illustration above to
help determine the correct Running Board. NOTE: The front stepping pad is
closer to the front end of the Running Board. Place the Running Board on top
of the Brackets.
IMPORTANT: Do not slide, (front to back), the Running Board on the Brackets or damage to the finish may result.
5. Locate the channel opening in the bottom of the Running Board. Select (3)
8mm Double Bolt Plates,(Figure 8). Insert the Bolt Plates into the channel in
the bottom of the Running Board closest to the Brackets, (Figure 9). Lift the
Running Board up and guide the studs through the Brackets.
6. Attach the Running Board to the Brackets with (8) 8mm Flat Washers and (8)
8mm Nylon Lock Nuts,(Figures 10—12).
7. Level and adjust the Running Board and fully tighten all hardware.
8. Repeat Steps 1—7 to install the Passenger/right side Running Board.
9. Do periodic inspections to the installation to make sure that all hardware
is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Running Board.
Driver/left side Installation Pictured
Driver/left side Installation Pictured
Driver/left side Installation Pictured
Product Specifications:
-
Fits: 2019-2024 Chevy Silverado/GMC Sierra 1500 Crew Cab (incl.
Diesel models with DEF tanks, 2022 Silverado 1500 LTD and 2022 Sierra 1500 Limited), 2020-2024 Chevy Silverado/GMC Sierra 2500/3500 Crew Cab (incl. Diesel models with DEF tanks) -
Part Numbers: WB-CS171BD/WB-CS171SD
-
Includes: 1 Driver/left side Running Board, 1 Passenger/right side Running Board, Mounting Brackets, Bolts, Washers, Nuts
Frequently Asked Questions (FAQ):
Q: Do I need any special tools for the installation?
A: You may need a socket wrench set and a torque wrench for proper installation.
Q: Can these running boards be installed on a different vehicle model?
A: These running boards are specifically designed for the mentioned Chevy Silverado/GMC Sierra models and may not fit other vehicles.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>