CLIM ART 621237 In Channel Incredibly Durable Rain Guards Installation Guide

June 14, 2024
Clim Art

CLIM ART 621237 In Channel Incredibly Durable Rain Guards

CLIM-ART-621237-In-Channel-Incredibly-Durable-Rain-Guards-
product

SIDE WINDOW DEFLECTORS
Before installing the deflectors, please read the manual. Incorrect installation of deflectors can cause damage to deflectors or personal injury.

COMPLETE SET

4 (2) Piece Sets (the product may differ from the illustration in the instructions)

CLIM-ART-621237-In-Channel-Incredibly-Durable-Rain-Guards-fig-
\(1\)

  1. Front Driver Side Window Deflector
  2. Front Passenger Side Window Deflector
  3. Rear Driver Side Window Deflector
  4. Rear Passenger Side Window Deflector
  5. Instruction Manual
  6. Plastic Blade (1 piece)
  7. Alcohol Wipe (2 pieces)
  8. Fastening Bracket (4 pieces)
  9. Metal Bracket (2 pieces)
  10. Transparent protective tape (1 piece)

ATTENTION! Protective film, DO NOT REMOVE!

Parts

  1. Deflector frame
  2. The rear section of the deflector
  3. The front section of deflector

Installation

FRONT DEFLECTORS

CLIM-ART-621237-In-Channel-Incredibly-Durable-Rain-Guards-fig-
\(4\)

  • 1.1 Make sure the car windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.
  • 1.2 Place a small section of the transparent protective tape, included with the complete set, onto the flat surface of the metal bracket as shown in the picture.
  • 1.3 Place the metal bracket onto the lower rubber seal as close to the front window frame as possible.
  • 1.4 Remove the protective liner from the tape on the deflector.
  • 1.5 Lower the front section of the deflector onto the metal bracket as shown in the illustration.
  • 1.6 Shift the deflector forward, fitting the deflector frame into the channel completely. Make sure the deflector is placed above the lower window frame.
  • 1.7 Bending the center part of the deflector outwards, in­sert the rear section of the deflector into the channel, leaving a gap above it.
  • 1.8 Starting with the front section of the deflector, insert it into the window channel.
  • 1.9 Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
  • 1.10 To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, it is strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.
  • 1.11 Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
  • 1.12 Repeat points 1.1 to 1.11 on the opposite side of the vehicle.
REAR DEFLECTORS

CLIM-ART-621237-In-Channel-Incredibly-Durable-Rain-Guards-fig-
\(5\) CLIM-ART-621237-In-
Channel-Incredibly-Durable-Rain-Guards-fig- \(6\)

  • 2.1 Make sure the car windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.
  • 2.2 To position the fixture, bend the edge of the rubber seal from the back frame ofthe window by 2-3 inches by using the provided special plastic blade as shown in the illustration.
  • 2.3 Place the fastening bracket in the channel and return the rubber seal to its original position. 1- Rubber seal; 2- Fastening bracket; 3 – Plastic blade; 4- Metal body frame of the door.
  • 2.4 The illustration demonstrates how to position the fastening bracket. 1 – Rubber seal; 2 – Deflector; 3 – Fastening bracket; 4 – Glass; 5 – Metal body frame of the door.
  • 2.5 Bend the edge of the rubber seal from the front frame of the window by 2-3 inches. Place the fastening bracket in the channel and return the rubber seal to its original position.
  • 2.6 Remove the protective liner from the tape on the deflector.
  • 2.7 The deflector must be installed starting at the rear. To do so, place the rear section of the deflector frame into the channel and move the front section upwards. Position the entire deflector frame into the window channel, placing the frame between the fastening brackets and the rubber seal as is shown in the illustration.
  • 2.8 Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
  • 2.9 To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, it is strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.
  • 2.10 Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
  • 2.11 Repeat points 2.1 to 2.10 on the opposite side ofthe vehicle.

Contact Information

CONGRATULATIONS!
Your unique and durable deflectors are installed for you to enjoy! From this moment on we hope you enjoy their appearance!

  • If you have any questions about warranty, technical aid, or requests for missing (lost) parts, do not hesitate to contact Customer Service: by phone: + 1 888 311 11 25, or by email: customerservice@sparklinesinc.com.
  • We are happy to serve you and your vehicle to produce high-quality products that have an ideal fit, easy installation, and enjoyment with everyday use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals