FINLUX FCH-1820 BG LED Glass Panel Heater Silent Energy Saving Compact Wall Mount Heater Instruction Manual

FINLUX FCH-1820 BG LED Glass Panel Heater Silent Energy Saving Compact

Wall Mount Heater

TECHNICAL DATA

• Model: FCH-1820 BG
• RATED VOLTAGE:   AC220-240V/50/60Hz
• POWER: 2000-2300W

GENERAL DIRECTIONS

1.  Remove the packaging and make sure that the appliance is intact. If in doubt, do not use it and contact our Technical Assistance Centre. Packaging materials (plastic bags, polystyrene, staples etc.) must be kept out of the reach of children as they could be hazardous.
   Caution:

   • The appliance must only be used by responsible adults;
   • For their own safety, children and persons with reduced mental capacities must not use the appliance unless under the supervision of responsible adults;

2.  Before connecting the appliance, check that the appliance rating corresponds to the mains rating.

3.  If the power cable is damaged, it must be replaced by the manufacturer or otherwise by a qualified person in order to prevent any risk.

4.  This appliance must only be used for the purpose for which it has been manufactured, i.e. for additional electrical heating in rooms. Any other use is considered improper and therefore dangerous. The manufacturer is not responsible for any damage caused by improper, incorrect or unreasonable use.

5.  Before cleaning or carrying out maintenance on the appliance, disconnect it from the electrical mains by removing the plug from the electrical outlet or by switching off the system switch.

6.  If the appliance is faulty and/or operating incorrectly, switch it off without tampering with it. If the above is disregarded, the safety of the appliance may be compromised.

7.  Switch off the appliance and remove the plug from the electrical outlet when not in use.

8.  The use of any electrical appliance calls for the awareness of some basic rules, such as:

   • do not use the appliance near sources of water such as baths, showers or swimming pools
   • do not touch the appliance with wet or damp hands or feet
   • do not leave the appliance exposed to atmospheric agents

9.  Do not use the appliance in the presence of potentially flammable or explosive liquids or gases.

IMPORTANT

1.  In order to avoid overheating, it is advisable to unwind the entire length of the power cord.
2.  Check that the electric capacity of the system and the power outlets are adequate for the maximum power stated on the plate. If in doubt, please contact a qualified professional.
3.  Do not leave the appliance plugged in when not required. Unplug the appliance from the mains after having switched it off when not in use.
4.  Do not obstruct the ventilation or heat dispersion openings.
5. 5. The power cord on this appliance must not be replaced by the user. If the cord is damaged or requires replacement, contact qualified personnel only.
6.  Avoid the hot contact, checking that the cord is not placed in front of the hot air outlet grille.
7.  Do not use near bathtubs, showers or basins (minimum distance 1 metre).
8.  Use in an upright position.
9.  Keep the suction grille clean.
10. Do not use the appliance immediately below a fixed power outlet.

WARNING: In order to avoid overheating, do not cover the heater.

CAUTION

1.  Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
2.  The heater must not be located immediately below a socket-outlet.
3.  Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
4.  Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised.
5.  Keep the appliance and its cord out of reach for the children less than 8 years.
6.  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
7.  Children of less than 3 years should be kept away unless continuously supervised.
8.  Children aged from 3 years and less than 8 years shall only switch on/off the appliance which provided that it has been placed or installed in its intended normal operating position, and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
9.  Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

PRODUCT FEATURES

1.  Aluminum shell, high thermal efficiency
2.  heating element: quick heating with higher energy savings.
3.  LCD display function information .
4.  Timer from 1 to 24 hours to turn the convector heater on or off at the desired time.
5.  Digital display with automatic room temperature display.
6.  Free standing with tripod.

FOOT ASSEMBLY

Before using the heater， the feet（supplied separately in the cartoon）， must be fitted to the unit. These are to be attached to the base of the heater using the 4 self-tapping screws provided, taking care to ensure that they are located correctly in the bottom ends of the heater side moldings.

Note: It is normal when the heaters are turned on for the first time or when they are turned on after having been used for a long period of time the heaters may emit some smell and fumes .This will disappear when the heater has been on a short while.

Operation panel function introduction

1. Selected heating level display

2. “Fan” symbol

3. “Frost protection” symbol

4. Selected unit of measurement display

5. Fan button

6. Increase temperature

7. Reduce temperature

8. Timer button

9. Running time display

10. Set temperature display

11. Measured temperature display

12. On/Off button

13. Infrared receiver for remote control

14. Wi-Fi button

15. Button for selecting the heat setting

16. Wi-Fi indicator lamp

17.  On/Off button

18.  Fan button

19.  Wi-Fi button

20.  Increase temperature

21.  Timer button

22.  Button for selecting the heat setting

23.  Reduce temperature

Key function introduction

POWER function
Insert the plug in a suitable power socket. After turn on the main switch (on the right side),the computer board emits a “click” sound,the screen displays the current room temperature,and turn on the panel control switch ,to enter the standby state and display the current room temperature and set temperature at the same time .In the meantime, other displays are not displayed. Then press the button for selecting the heat setting ,you can select the 1000/1300/2300W/Anti-frost four modes . When you select the 1000W or 1300W or 2300W .The heater will be heated according to your setting.

Timer and temperature setting

Timer
Press the timer button, each time the time is increased by 1 hour, when the timer time is 24:00, press the timer button, then the function is turned off, when the timer function is set, the timer countdown starts in 5 seconds, and after the timer is over, it enters standby mode;

Temperature
Press the temperature shift key to change the temperature display mode. The default is Celsius degree. Press 1 time, degree to Fahrenheit and 2 times conversions. Press “+” or “-” key to set the temperature (set temperature must be greater than the current temperature) . For Celsius, cycle through Internal temperature (room temperature) is displayed every time the appliance is started up. The temperature can be set when the appliance is in stand-by or heating. When the room temperature reaches the set level, the heater stops to work ;When room temperature is 1 degrees over the set temperature, the heater also will stop tor work .The heater will begin operating again only when temperature decreases 1 degrees with respect to the set temperature. The temperature regulation
range is 5°C-37°C.

Mode
Press “4-mode” to regulate 1000W /1300W/2300W/ANTI-FROST temperature power.

FAN
Press the fan to open the key, you can open the fan or turn off the fan (on the screen fan icon is light fan, Figure off the wind organ); In anti-frost mode: In the standby mode, the room temperature is lower than 5°C, and automatically enters the high-grade (2300W) heating mode. When the room temperature reaches 9°C, the heating is turned off to standby, followed by cycling.

Operating sound
The appliance emits a beep upon each operation setting.

LCD room temperature display: the appliance will stop when the temperature exceeds 1 degrees with respect to the set temperature.

Memory
The appliance can hold the last temperature setting in its memory. This temperature will be shown at each start-up.

CONNECTING THE APPLIANCE TO WIFI

DOWNLOAD THE APP TO YOUR PHONE Download the ”TUYA SMART” app, from your chosen app store, using the QR codes below, or by searching for the app in your chosen store.

MODE FOR SETUP

The heater has one setup mode, AP (Access Point). The AP connection uses a direct local WiFi connection between your phone and the heater to upload the network details. When first turned on using the main switch on the right side of the unit, the WiFi will be turned off. To turn on the WiFi, press and hold the Wi-Fi button for 3 seconds. The WiFi indicator will flash quickly to indicate the unit is in AP connection mode. Please ensure your device is in the correct WiFi connection mode for the connection type you are attempting, the flashing WiFi indicator on your heater will indicate this.

TURNING THE WIFI OFF
To turn the WiFi off, the appliance can be turned off using the main switch on the right side or press and hold the Wi-Fi button for 5 seconds . When the unit is turned back on it will start with the WiFi turned off, until reactivated following the steps above.

REGISTER THE APP

SETTING UP YOUR HOME WITHIN THE APP
TUYA is designed so it can work with a large number of compatible smart devices within your home. It can also be set up to work with multiple devices within different houses as such during the setup process the app requires that different areas are created and named to allow easy management of all your devices. When new devices are added, they are assigned to one of the rooms you have created.

CREATING ROOMS

CONNECTING USING APP MODE ALTERNATIVE METHOD
Before initiating the connection, make sure the unit is in standby mode(Power switch ON, but unit turned off), with the WiFi Light Indicator flashing once per second. Also ensure your phone is connected to the WiFi network. (We advise turning mobile data off during setup.

CONTROLLING YOUR APPLIANCE THROUGH THE APP

THE HOME SCREEN

Each device has its own entry on the home screen to allow the user to either quickly turn the unit on or off, or to enter the device screen to make other changes.

DEVICE SCREEN
The device screen is the main control screen for the heater, providing access to the controls to amend the functions and settings.

SMART SCENES
Smart Scenes is a powerful tool providing the option to customize the operation of the air heater based both on conditions within the room and outside influences. This gives the user the option of specifying much more intelligent actions. These are split into two categories Scene and Automation.

SCENE
Scene allows for a one-touch button to be added to the Home Screen. The button can be used to change a number of settings in one go and can change all the settings within the unit. A number of scenes can easily be set up, allowing the user to easily change between a number of preset configurations. Below is an example of how to set up a scene:

AUTOMATION
Automation allows an automatic action to be set up for the device. This can be triggered by the Time, and a range of other influences, depending on what other TUYA enabled devices you have on the network.

CONNECTION TROUBLESHOOTING

1.  Check whether the device is powered on and is in the correct WiFi connection mode, if not please refer to the CHANGING BETWEEN CONNECTION MODES section.
2.  Ensure the WiFi password has been entered into the app correctly (Case sensitive)
3.  Check that the phone is connected to the WiFi you are connecting the device to.
4.  Ensure the network you are connecting it to is 2.4Ghz (5Ghz WiFi networks are not supported), and that there is a strong WiFi signal to the item.
5.  If your router is dual band, ensure that the 2.4ghz network has a different network name (SSID). Further advice on changing router settings will be available from your Internet service provider / Router manufacturer.
6.  Check the settings on the router. Encryption should be WPA2-PSK and authorisation type should be set to AES

MAINTENANCE

Before carrying out routine cleaning, switch off the product and disconnect main power. Use a soft, damp cloth only and do not use abrasive substances.
Note: Do not submerge any part of the product in the water.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>